Installation Manual

ManualsBrandsAltronix ManualsAccessories for electricalAL600ULXD

Overview:

Altronix AL600ULXD power supply/charger converts a 115VAC 60Hz or 230VAC 50/60Hz input into a non

power-limited 12VDC or 24VDC output (see specifications).

Specifications:

AL600ULXD

Power Supply/Charger

Agency Listings:

• UL 294* Safety Access Control System Units,

UL 1481 Power Supplies for Fire-Protective

Signaling Systems.

• CE European Conformity.

Input:

• 115VAC, 60Hz, 1.9A or 230VAC, 50/60Hz, 0.95A.

Output:

• 12VDC or 24VDC selectable output.

• 12VDC or 24VDC @ 6A supply current.

• Filtered and electronically regulated output.

• Short circuit and thermal overload protection.

Battery Backup:

• Built-in charger for sealed lead acid or

gel type batteries.

• Automatic switch over to stand-by battery

when AC fails.

• Maximum charge current 0.7A.

Supervision:

• AC fail supervision (form “C” contacts).

• Low battery supervision (form “C” contacts).

Visual Indicators:

• AC input and DC output LED indicators.

Features:

• Low battery disconnect.

• Unit is complete with transformers, power supply,

grey enclosure, and cam lock.

• Battery leads included.

Enclosure Dimensions (H x W x D approx.):

15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm).

Accommodates up to two 12VDC/12AH batteries.

AL600ULXD: Grey Enclosure.

AL600ULXDR: Red Enclosure.

*Access Control Performance Levels: Destructive Attack - I; Endurance - IV; Line Security - I; Stand-by Power - IV.

Power Supply Output Selection:

Output

Switch Position

12VDC SW1 ON

24VDC SW1 OFF

Stand-by Specifications:

Output

4 hr. of Stand-by and

5 min. of Alarm

24 hr. of Stand-by and

5 min. of Alarm

60 hr. of Stand-by and

5 min. of Alarm

12VDC / 40AH Battery

Stand-By = 6.0A

Alarm = 6.0A

Stand-By = 1.0A

Alarm = 6.0A

Stand-By = 300 mA

Alarm = 6.0A

24VDC / 12AH Battery –

Stand-By = 200 mA

Alarm = 6.0A

–

24VAC / 40AH Battery

Stand-By = 6.0A

Alarm = 6.0A

Stand-By = 1.0A

Alarm = 6.0A

Stand-By = 300 mA

Alarm = 6.0A

Summary of content (4 pages)

PAGE 1
AL600ULXD Power Supply/Charger Overview: Altronix AL600ULXD power supply/charger converts a 115VAC 60Hz or 230VAC 50/60Hz input into a non power-limited 12VDC or 24VDC output (see specifications). Specifications: Agency Listings: • UL 294* UL 1481 • CE Safety Access Control System Units, Power Supplies for Fire-Protective Signaling Systems. European Conformity. Input: Supervision: • AC fail supervision (form “C” contacts). • Low battery supervision (form “C” contacts).
PAGE 2
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding.
PAGE 3
BAT FAIL AC FAIL NC C NO NC C NO Class 2 power-limited Fig. 1 ON OFF = 24V SW1 ON = 12V AL600ULB DC AC + DC - + BAT - AC AC non power-limited Input 115VAC 60Hz, 1.9A or 230VAC 50/60Hz, 0.95A 3 2 1 WHITE 4 BLUE 5 YELLOW 1 WHITE 2 NEUTRAL LINE 115VAC Input AL600ULXD 3 BLUE YELLOW 4 BLACK 5 Fig. 3 - 230VAC Input BLACK Fig.
PAGE 4
Enclosure Dimensions (H x W x D approximate): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) 1.5” (38.1mm) 4.615” (117.2mm) 4.615” (117.2mm) 1.5” (38.1mm) 1.75” (44.5mm) 1.25” (31.8mm) 4.5” (114.3mm) 1.1” (27.9mm) 12.23” (310.6mm) 4.5” (114.3mm) 1.1” (27.9mm) 1.375” (34.9mm) 1.5” (38.1mm) 1.25” (31.8mm) 1.5” (38.1mm) 0.91” (23.1mm) 0.91” (23.1mm) 1.125” (28.6mm) 15.5” (393.7mm) 2.0” (50.8mm) 2.0” (50.8mm) 5.0” (127.0mm) 0.79” (20.1mm) 5.0” (127.0mm) 1.25” (31.8mm) 1.25” (31.8mm) 1.