Data Sheet

ManualsBrandsAltronix Manualselectrical connectionAL1024ULM

Input:

• Input 115VAC, 60Hz, 4.2 amp.

• Input fuse rated @ 3.5 amp/250V.

• Fire Alarm Panel or Access Control System trigger

inputs. N.O. or N.C. supervised trigger input and

polarity reversal trigger input.

Output:

• 24VDC outputs.

• 10 amp supply current.

• Five (5) PTC protected Class 2 Rated power-limited

outputs, rated @ 2 amp.

• Output relay energizes when unit is triggered

(form “C” contact rated 1 amp @ 28VDC).

• Filtered and electronically regulated output.

• Short circuit and thermal overload protection.

Battery Backup:

• Built-in charger for sealed lead acid or

gel type batteries.

• Automatic switch over to stand-by battery

when AC fails.

• Maximum charge current 0.7 amp.

Supervision:

• AC fail supervision (form “C” contacts).

- Notification trigger is selectable for

30 seconds (factory set) or 6 hours.

• Low battery supervision (form “C” contacts).

• Battery presence supervision (form “C” contacts).

• Power fail supervision relay (form “C” contacts).

Visual Indicators:

• AC input and DC output LED indicators

(power supply board).

• Red LEDs indicate condition of power outputs

(multi-output board).

• Power and input trigger LEDs (multi-output board).

Electrical:

• Operating temperature: 0º C to 49º C ambient.

• 122.84 BTU/Hr.

• System AC input VA requirement: 483VA.

Mechanical:

• Enclosure Dimensions (H x W x D approx.):

15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm)

- Accommodates up to two (2) 12VDC/12AH batteries.

• Product weight (approx.): 10.8 lbs. (4.90 kg).

• Shipping weight (approx.): 11.8 lbs. (5.35 kg).

Specifications

AL1024ULM

Multi-Output Power Supply/Charger

Rev. DSAL1024ULM _05212015

AL1024ULM multi-output access control power supply/charger is specifically

designed for use with access control systems and accessories. This unit con-

verts a 115VAC, 60Hz input into five (5) individually protected Class 2 Rated

power-limited 24VDC outputs. Each output will route power to a variety of ac-

cess control hardware devices including Mag Locks, Electric Strikes, Magnetic

Door Holders, etc. These outputs will operate in both Fail-Safe and Fail-Secure

modes. Controlled trigger input is achieved through normally open (N.O.) or

normally closed (N.C.) supervised input or the polarity reversal from an FACP

(Fire Alarm Control Panel). A form “C” dry output relay enables HVAC Shut-

down, Elevator Recall or it may be used to trigger auxiliary devices.

Overview

AL1024ULM

Agency Approvals

UL 294 UL Listed for Access Control

System Units.

UL 1481 UL Listed Standard for Safety for

Fire Protective Signaling Systems.

CUL Listed - CSA Standard C22.2

No.205-M1983, Signal Equipment.

Altronix Corp.

140 58th St. Brooklyn, NY

CSFM - California State Fire

Marshal Approved.

Summary of content (2 pages)

PAGE 1
AL1024ULM Multi-Output Power Supply/Charger Rev. DSAL1024ULM _05212015 Overview AL1024ULM AL1024ULM multi-output access control power supply/charger is specifically designed for use with access control systems and accessories. This unit converts a 115VAC, 60Hz input into five (5) individually protected Class 2 Rated power-limited 24VDC outputs. Each output will route power to a variety of access control hardware devices including Mag Locks, Electric Strikes, Magnetic Door Holders, etc.
PAGE 2
Enclosure Dimensions (H x W x D approximate): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.