Installation Instructions

- 2 - ACMCB220 Series Installation Guide
Overview:
Altronix ACMCB220 Series units distribute and switch power to access control systems and accessories. They
convert a 220VAC (working range 198VAC - 256VAC), 50/60Hz input into eight (8) independently controlled
12VDC or 24VDC PTC protected outputs. Outputs are activated by an open collector sink or normally open (NO) dry
trigger input from an Access Control System, Card Reader, Keypad, Push Button, PIR, etc. Units will route power
to a variety of access control hardware devices including: Mag Locks, Electric Strikes, Magnetic Door Holders, etc.
Outputs will operate in both Fail-Safe and/or Fail-Secure modes. The FACP Interface enables Emergency Egress,
Alarm Monitoring, or may be used to trigger other auxiliary devices. The fire alarm disconnect feature is individually
selectable for any or all of the eight (8) outputs.
ACMCB220 Series Configuration Reference Chart:
Altronix
Model Number
12VDC
Total
Output
Current
24VDC
Total
Output
Current
PTC
Outputs
(auto-
resettable)
Individual
Output
Rating
220VAC
50/60Hz
Input
Current
Draw
Power
Supply
Board
Input
Fuse
Rating
Power
Supply
Board
Battery
Fuse
Rating
AL400ACMCB220
4A 3A
8 2.5A
1.2A
5A/250V
15A/32V
AL600ACMCB220
6A 6A 1.5A –
AL1012ACMCB220
10A – 2.2A
15A/32V
AL1024ACMCB220
– 10A 3A
Specifications:
Input:
• Power supply input options:
a) One (1) common power input for ACM8CB
and lock power (factory installed).
b) Two (2) isolated power inputs - One (1) to power
the ACM8CB and one (1) for lock accessory
power (external power supply is required).
Current is determined by the power supply
connected, not to exceed a maximum of 10A total.
• Eight (8) Access Control System trigger inputs.
Input options:
a) Eight (8) normally open (NO) inputs.
b) Eight (8) open collector inputs.
c) Any combination of the above.
Output:
• 12VDC or 24VDC outputs.
• Power-limited outputs.
• Eight (8) independently controlled
Fail-Safe and/or Fail-Secure power outputs.
• Eight (8) auxiliary power outputs (unswitched)
• Output PTCs are rated @ 2.5A.
• Filtered and electronically regulated outputs
(built-in power supply).
Visual Indicators:
• Red LEDs indicate outputs are triggered
(relays energized).
• Green LED indicates FACP disconnect is triggered.
• AC input and DC output LED indicators.
Battery Backup:
• Built-in charger for sealed lead acid or
gel type batteries.
• AL400XB2V, AL600XB220, and AL1012XB220
(Power Supply Board) maximum charge current
0.7A. AL1024XB2V (Power Supply Board)
maximum charge current 3.6A.
• Automatic switch over to stand-by battery when
AC fails.
• AC input and DC output LED indicators.
• Zero voltage drop when unit switches over to
battery backup (AC failure condition).
• Battery fail and battery presence supervision
(form “C” contact).
Features:
• Fire Alarm disconnect (latching or non-latching)
is individually selectable for any or all of the
eight (8) outputs.
• Fire Alarm disconnect input options:
a) Normally open (NO) or normally closed (NC)
dry contact input.
b) Polarity reversal input from FACP
signaling circuit.
• Alarm output relay indicates that FACP input is
triggered (form “C” contact rated @ 1A 28VDC).
• Short circuit and thermal overload protection.
Enclosure Dimensions (H x W x D approx.):
• 15.5” x 12” x 4.5”
(393.7mm x 304.8mm x 114.3mm).
• Enclosure accommodates up to two (2)
12AH batteries.