User`s manual

- MIXER
Interfacing to a Mixing Console
The VERB can accept mono or stereo sends at all system levels. The input circuitry of the VERB can easily
accept professional levels while having enough input and output gain to interface with the low signal levels of
home recording systems.
MONO IN, STEREO OUT. Again set manually the MONO ON/OFF switch to position ON. Connect one audio cable
to the from a mono source, and now two other audio cables from the OUTPUT 1 and OUTPUT 2 of theINPUT 2
VERB to a stereo amplification system or two mixer inputs.
MONO. Set manually the MONO ON/OFF switch to position ON. Connect one audio cable to the of theINPUT 2
VERB from a mono source, and one or two other audio cables from the OUTPUT 1 and OUTPUT 2 of the
VERB to a mono/stereo amplification system or one/two mixer inputs.
To Amplifier or Mixing Console
OUTPUT 1
From Instrument or Effects Send
INPUT 2
OUTPUT 2
To Amplifier or Mixing Console
OUTPUT 1
From Instrument or Effects Send
INPUT 2
OUTPUT 2INPUT 1
To Amplifier or Mixing Console
OUTPUT 1
From Instrument or Effects Send
INPUT 2
DIGITAL MIX
ON / OFF
UTILEDITESCENTER
DOWN
UP
ON
OFF
POWER
24 32 BIT
DIGITAL EFFECTS
VERB
SAVING
PRESET
PROCESS
OVERFLOW
PROCESS
OVERFLOW
R
LTO
OUTPUT LEVEL
INPUT LEVEL MIX
10
OFFWETDRY
10
OFF
DIGITAL MIX
ON / OFF
UTILEDITESCENTER
DOWN
UP
ON
OFF
POWER
24 32 BIT
DIGITAL EFFECTS
VERB
SAVING
PRESET
PROCESS
OVERFLOW
PROCESS
OVERFLOW
R
LTO
OUTPUT LEVEL
INPUT LEVEL MIX
10
OFFWETDRY
10
OFF
DIGITAL MIX
ON / OFF
UTILEDITESCENTER
DOWN
UP
ON
OFF
POWER
24 32 BIT
DIGITAL EFFECTS
VERB
SAVING
PRESET
PROCESS
OVERFLOW
PROCESS
OVERFLOW
R
LTO
OUTPUT LEVEL
INPUT LEVEL MIX
10
OFFWETDRY
10
OFF
-18
-24
-30
-6
-12
CLIP
-18
-24
-30
-6
-12
CLIP
-18
-24
-30
-6
-12
CLIP
7
MIXING CONSOLE
Aux
Return
Aux
Send
DIGITALMIX
ON / OFF
UTILEDITESCENTER
DOWN
UP
ON
OFF
POWER
24 32 BIT
DIGITAL EFFECTS
VERB
SAVING
PRESET
PROCESS
OVERFLOW
PROCESS
OVERFLOW
R
LTO
OUTPUT LEVEL
INPUT LEVEL MIX
10
OFFWETDRY
10
OFF
-18
-24
-30
-6
-12
CLIP
STEREO. Set manually the MONO ON/OFF switch to position OFF. Connect two audio cables to the INPUT 1
and INPUT 2 of the VERB from a stereo source, and two other audio cables from the OUTPUT 1 and
OUTPUT 2 of the VERB to a stereo amplification system or two mixer inputs.
The VERB may be connected to a mixing console using Aux sends and returns. Another way of interfacing the
VERB to a mixer or recording console would be in-line between the output of your mixing console and the
input of a tape deck or power amplifier. This last setup would be used only if you wanted to effect the entire mix.
Using Aux Sends and Returns
Generally, on mixing consoles are available two types of auxiliary sends: pre-fader sends (headphone or monitor),
and post-fader sends for effects units. Typically, if a mixer has more than two sends per channel (4, 6 or 8, per-
haps), the first two sends are reserved for the pre-fader sends, while the remaining sends are used to send the
signal to be effected to devices as the VERB. Connect the VERB using post-fader sends, so fading a channel
out, its effects will fade also.
Using a mixer's aux sends allows each channel to have its own level control going to the aux output. It is possible
to mix all the channels we want to be sent to the effects by using the individual channels' aux send levels on the
mixer. Most consoles also have aux master controls, which set the overall level of each aux output.