User`s manual

DSP
TO MAIN
DSP
TO MON
PRESETS
DSP
PRESETS:
VARIATIONS
CLIP
MUTE
DSP
MUTE
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
8
FOOT
SW.
14 REVERB DELAY
16 REVERB CHORUS
15 REVERB FLANGER
5 LARGE ROOM
13 CHORUS
12 FLANGER
11 STEREO DELAY
10 MONO DELAY
9 SPRING REVERB
8 TAPE REVERB
7 PLATE
6 SMALL ROOM
4 SMALL HALL
3 LARGE HALL
2 VOCAL 2
1 VOCAL 1
-
+10dB
8
-
+10dB
11
12
SP
OTLIG
HT
4. CONTROL ELEMENTS
This switch is used to activate/deactivate the effect
facility. For convenient operation, you can also use the
following FOOT SW jack.
DSP MUTE Switch
This LED lights up when the input signal is too strong or
in case of the digital effect module being muted.
CLIP/MUTE LED
This control is used to control the volume of effect signal
sent to monitor mix, which can be varied from - to
+10dB.
DSP TO MON Control
Adjust this knob to select the effect you wish to
perform. There are 16 options available: several kinds
of reverb, mono and stereo delay, modulation effects,
and versatile two-effect combination.
PRESETS Control
4.4 DSP Section
PBM8.350 UM features 256 position effects, for
details, please refer to following content.
VARIATIONS Control
Since you have selected the needed effect, please go
ahead with the fine consideration, there are also 16
variations for each preset, and each variation has been
designed modifying several parameters.
To this 1/4" jack, you can connect an external footswitch to turn on/off the
onboard effect module.
FOOT SW. Jack
This control is used to control the volume of effect signal sent to main mix bus,
which can be varied from - to +10dB.
DSP TO MAIN Control
SPOTLIG
HT
4. CONTROL ELEMENTS
4.5 Rear Panel
This switch is used to turn the main power ON and OFF.
POWER ON/OFF Switch
Use it to connect your PBM8.350 UM to the main AC with the supplied AC
cord. Please check the voltage available in your country and how the voltage for
your PBM8.350 UM is configured before attempting to connect your
PBM8.350 UM to the main AC.
AC Inlet with FUSE Holder
These jacks are used to connect speakers. They are configured with 4-way
speakon connectors and 1/4" phone jacks. You can determine the signal that is
output to these jacks according to the setting of AMPLIFIER MODE select
switch.
Note: In order to avoid damaging your PBM8.350 UM built-in amplifier, please
pay more attention to the speaker impedance . Lower load impedances are not
permitted.
SPEAKERS Jacks
AC Select SwitchAC Select Switch
This switch has two choices for voltage, 115 VAC or 230 VAC.
Note: If you want to switch the voltage, remove the cover plate with a
screwdriver and set the switch to the 115 VAC or 230VAC as the actual
requirement. Refer to the specification page 20 for instructions of replacing
fuse.
29
26
33
26
36
34
35
28
27
30
31
32
11
11
11
11
11
11
11
26
27
28
29
30
31
32
11
11
11
11
33
34
35
36
CAUTION:
REPLACE WITH THE SAME TYPE FUSE AND RATING
DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE
WARNING: SHOCK HAZARD - DO NOT OPEN
AVIS: RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR
STEREO MODE: 2 350 W @ 4 OHM
2 180 W @ 8 OHM
(4 OHM MIN. LOAD).
BRIDGE MODE: 700 W @ 8 OHM
(8 OHM MIN. LOAD).
CLASS 2 WIRING MAY BE USED
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
POWERED MIXER
MODEL: PBM8.350 UM
VOLTAGE SELECTOR
OUTPUT 2
1+ 1-
POS NEG
LEFT/MONO MAIN/
Apparaten skall anslutas
till jordat uttag nar den
ansluts till ett natverk
RIGHT/MONITOR/
OUTPUT 1
1+ 1-
POS NEG
BRIDGE
2+ 1+
POS NEG
BRIDGE MODE
OUTPUT 2
OUTPUT 1
MODEL
SERIAL
DESIGNED IN ITALY
T10AH 250V
CLASS 2 WIRING
CLASS 2 WIRING
ON OFF
POWER
AC INPUT
RATED POWER CONSUMPTION:880W
220 - 240V~50Hz
100 - 120V~60Hz
FUSE:
220-240V: T5AH 250V
100-120V: