Specifications

DUAL STEREO MULTIEFFECTS DSP
With 56-bit internal DSP and 24-bit Delta-Sigma conversion, the
two internal effects (160 programs each) provide high performance
digital audio processing combined with extremely easy operation.
26 ➤ 2-Line (E1 and E2) Liquid Crystal Display. Shows the numbers
and the names of the currently selected program.
27 ➤ E1/E2 BUTTON: it allows operating on E1 or E2 lines on the
LCD (E1 and E2 are the two groups of effects).
28 ➤ PROGRAMS selection knob: allows selecting one of the 160
programs available for each of the two effects (E1 and E2).
29 ➤ LOAD BUTTON: allows loading and activating the program
selected with the PROGRAMS knob.
= shows that the selected program has been loaded.
= shows that the selected program has not been loaded yet.
30 ➤ INPUT LEVEL: 5-segment input level LED indicator.
A good setting of the effect sends (E1 and E2) on each channel will
produce continuous lighting of the green LED segments, while the
red segment must ash only occasionally.
☞ If the red LED is continuously lighted it indicates signal overload
and it is necessary to reduce the effect send volumes (E1 and E2)
on individual channels.
31 ➤ TONE control: turning this control clockwise produces a gra-
dual decrease in high frequencies. Fully anticlockwise the response
is at.
32 ➤ A / B / C / D / E / F: monitor sends (pre-fader). They allow to
adjust the level of the stereo effect in the monitor outputs.
33 ➤ BAL: balance. Allows to adjust the level of the stereo signal
in the L and R master outputs.
34 ➤ ON: effect on/off button, with green LED indicator.
35 ➤ VOLUME faders. They control the effect's volume on master
outputs.
● connections:
36 ➤ EFF FT/SW - MUTE: jack sockets for connection of remote
footswitches. They allow remote control enabling/disabling of the
built-in effect processors. This is possible only when the "ON"
buttons are pushed. The red LED indicators light when the effects
are 'off' (muted).
12
CONTROLS AND CONNECTIONS
EXTERNAL EFFECTS SENDS AND RETURNS
37 ➤ 1 / 2 EXT. EFF. SEND: level controls for the external effects
sends. They adjust the level of the signals at the 'EFF SEND 1' and
'EFF SEND 2' jack outputs. These signals are the mix of the E1 and
E2 controls of all input channels.
Each one of the two STEREO RETURNS features:
38 ➤ VOL: adjusts the volume of the return signal sent to the
master L/R outputs.
39 ➤ BAL: stereo balance of the external effect. Allows to adjust
the level of the stereo signal of the effect in the L and R master
outputs.
40 ➤ A / B / C / D / E / F: monitor sends controls.
They set the level of the external effect return in the two monitor
outputs.They depend on the volume control (38).
● connections:
41 ➤ EFF SEND 1/2: jack output socket for the external effects
sends.
42 ➤ STEREO EFF RET 1/2: jack inputs for the stereo external
effect return.
• The EFF RET L and R inputs are standard stereo line inputs. You can thus
use them to connect any line signal (such as the L/R outputs of a second
mixer, instruments, expanders…)
■ Connect the inputs of the external effects to the EFF SEND 1/2
sockets.
■ Connect the L and R outputs of the external effects to the
L and R EFF RET 1 and EFF RET 2 inputs of the effects return.
• For a mono effect connect its 'only effect' output to the 'L / mono' socket.
■ Use the E1 and the E2 controls on each channel to adjust the
quantity of channel signal to be sent to the external effects, the
EFF SEND 1 and EFF SEND 2 controls (37) to adjust the quantity
of signal to be sent to the EFF SEND 1 and EFF SEND 2 outputs.
Use the A, B, C, D, E, F, VOL and BAL controls (40, 38, 39) to adjust
the effect return level in the monitor 'A', 'B', 'C', 'D', 'E', 'F' outputs
and in the master 'L' and 'R' outputs.
On the channels where the external effect is not desired turn the
effect send (E1 or E2) knob fully anticlockwise.
☛ see g. 5 page 24
ENGLISH