Heated Display Cases ® Full Service or Self Service Models: ED2-48; ED2SYS-48 ED2-48/P; ED2SYS-48/P EU2SYS-48; EU2SYS-48/P ED2-48 ED2-72; ED2SYS-72 ED2-72/P; ED2SYS-72/P ED2-72/PL; ED2SYS-72/PL ED2-72/PR; ED2SYS-72/PR EU2SYS-72; EU2SYS-72/P EU2SYS-72/PL EU2SYS-72/PR ED2-72 ED2-96; ED2SYS-96 ED2-96/PL; ED2SYS-96/PL ED2-96/PR; ED2SYS-96/PR EU2SYS-96; EU2SYS-96/P EU2SYS-96/PL EU2SYS-96/PR ED2-96 • INSTALLATION • OPERATION • MAINTENANCE W 1 6 4 N 9 2 2 1 W a t e r S t r e e t • P.O.
® D E L I V E RY U N PA C K I N G This Alto-Shaam appliance has been thoroughly tested and inspected to insure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See Transportation Damage and Claims section located in this manual. This appliance, complete with unattached items and accessories, may have been delivered in one or more packages.
SAFETY PROCEDURES AND PRECAUTIONS Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols may be used throughout this manual. Used to indicate the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the warning included with this symbol is ignored.
I N S TA L L AT I O N METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. IMPROPER INSTALLATION, ALTERATION, ADJUSTMENT, SERVICE OR MAINTENANCE COULD RESULT IN SEVERE INJURY, DEATH OR CAUSE PROPERTY DAMAGE. TO PREVENT PERSONAL INJURY, USE CAUTION WHEN MOVING OR LEVELING THIS APPLIANCE.
I N S TA L L AT I O N S I T E I N S TA L L AT I O N 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER 32-15/16" (837mm) 34-1/4" (870mm) 44-5/16" (1125mm) ED2 PROFILE 47-11/16" (1212mm) 27-3/16" (691mm) 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER 26-7/16" (672mm) ED2SYS-72 ELECTRICAL PANEL ELECTRICAL OUTLET 47-11/16" (1212mm) 20-3/16" (513mm) 26-1/8" (664mm) 48" (1219mm) 47-1/8" (1196mm) 72" (1829mm) ED2SYS-96 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER ELECTRICAL PANEL ELECTRICAL OUTLET 47-11/16" (1212m
I N S TA L L AT I O N S I T E I N S TA L L AT I O N EU2SYS SERIES 5-1/2" (140mm) Swivel Caster 57" (1448mm) 30-1/2" (775mm) ELECTRICAL PANEL ELECTRICAL OUTLET 57" (1448mm) 30-1/2" (775mm) 26-1/2" (673mm) 44-5/16" (1125mm) Swivel Caster 5-1/2" (140mm) EU2SYS-48 48" (1219mm) 32-1/2" (824mm) 5-1/2" (140mm) ELECTRICAL PANEL ELECTRICAL OUTLET 57" (1448mm) 30-1/2" (775mm) 26-1/2" (673mm) EU2SYS PROFILE Swivel Caster EU2SYS-72 Rigid Caster Swivel Caster 5-1/2" (140mm) Swivel Caster Rigid Ca
I N S TA L L AT I O N ELECTRICAL CONNECTION The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes. To avoid electrical shock, this appliance MUST be adequately grounded in accordance with local electrical codes or, in the absence of local codes, with the current edition of the National Electrical Code ANSI/NFPA No. 70.
I N S TA L L AT I O N ED2 & ED2SYS & EU2SYS SERIES — OPTIONS & ACCESSORIES DESCRIPTION ED2-48 — — ED2-72, ED2-72/P — 5004182 — ED2-72/PL — 5004183 — ED2-72/PR — 5004184 — ED2-96 — — 5004185 ED2-96/PL — — 5004186 ED2-96/PR — — 5004187 5001143 5001143 5001143 STAINLESS STEEL 5001281 5001282 5001283 CUSTOM COLOR P148 P152 P153 5001293 5001295 5001297 P154 P155 P156 5001287 5001289 5001291 P157 P158 P159 1001990 1001991 — RIGHT- HAND 5001307 5001307 50013
O P E R AT I N G I N S T R U C T I O N S U S E R S A F E T Y I N F O R M AT I O N METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. The Alto-Shaam heated display case is intended for use in commercial establishments by qualified operating personnel where all operators are familiar with the purpose, limitations, and associated hazards of this appliance.
O P E R AT I N G I N S T R U C T I O N S O P E R AT I N G P R O C E D U R E S 1. DO NOT ADD WATER TO DISPLAY CASE Halo Heat display cases maintain a constant but gentle temperature and eliminate much of the moisture loss associated with conventional display cases. Because of this gentle heat, it is not necessary to add water to the display case. As a matter of fact, adding water is not recommended since water will accelerate the deterioration of the product, and may damage the unit voiding the warranty. 2.
O P E R AT I N G I N S T R U C T I O N S Indicator Lights LI-3027 Light Switch SW-33896 Cutting Board Bracket Thermostats TT-3498 BT-2342 Operator/Control side with cutting board Electrical Cord CD-3291 Plug Thermostat TT-3498 PG-3267 Cutting Board ED2-48, ED2SYS-48 – 4016 (1) ED2-72, ED2SYS-72 – 4017 (1) ED2-96, ED2SYS-96 – 4016 (2) #868 • ED2 & EU2 Series Operation & Care Manual • 10
O P E R AT I N G I N S T R U C T I O N S PAN CONFIGURATIONS • HEATED DISPLAY CASES ED2-72 ED2-96 ED2-48 GN 1/2 STANDARD PAN SIZES FULL-SIZE PAN 12" x 20" x 2-1/2" (325mm x 530mm x 65mm) GN1/1 ONE-HALF SIZE PAN 12" x 10" x 2-1/2" (325mm x 265mm x 65mm) GN1/2 TWO-THIRDS SIZE PAN 12" x 14" x 2-1/2" (325mm x 352mm x 65mm) GN2/3 ONE -THIRD SIZE PAN 12" x 6" x 2-1/2" (325mm x 176mm x 65mm) GN1/3 One (1) FULL-SIZE PAN and one (1) ONE-THIRD SIZE PAN per pan zone.
O P E R AT I N G I N S T R U C T I O N S PAN CONFIGURATIONS • SELF-SERVE HOT DISPLAY CASES PAN LAYOUT ➔ ED2SYS-72/PL & ED2SYS-72/PR ➔ DIAGRAM ED2SYS-96/PL ED2SYS-96/PR 5 P AN ZONE S 3 P AN ZONE S ONE-THIRD ONE-HALF SIZE PAN SELF-SERVE PAN ZONE SIZE PAN TWO-THIRDS SIZE PAN ONE-THIRD SIZE PAN FULL-SIZE PAN ONE-HALF SIZE PAN PAN SIZE: ITEM #1000521 21-5/8" x 26-3/8 x 2" (549mm x 670 mm x 51mm) ONE-THIRD ONE-THIRD SIZE PAN SIZE PAN ONE-THIRD SIZE PAN SIZE PAN Two (2) ONE -HALF SIZE PANS and
O P E R AT I N G I N S T R U C T I O N S 1002585 1000544 1002619 Part No.
O P E R AT I N G I N S T R U C T I O N S GENERAL HOLDING GUIDELINES Chefs, cooks and other specialized food service personnel employ varied methods of cooking. Proper holding temperatures for a specific food product must be based on the moisture content of the product, product density, volume, and proper serving temperatures. Safe holding temperatures must also be correlated with palatability in determining the length of holding time for a specific product.
CARE AND CLEANING CLEANING AND PREVENTIVE MAINTENANCE PROTECTING STAINLESS STEEL SURFACES CLEANING AGENTS It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, or inappropriate chemicals can completely destroy the protective surface layer of stainless steel. Abrasive pads, steel wool, or metal implements will abrade surfaces causing damage to this protective coating and will eventually result in areas of corrosion.
CARE AND CLEANING EQUIPMENT CARE Under normal circumstances, this appliance should provide you with long and trouble free service. There is no preventative maintenance required, however, the following Equipment Care Guide will maximize the potential life and trouble free operation of this appliance. The cleanliness and appearance of this equipment will contribute considerably to operating efficiency and savory, appetizing food. Good equipment that is kept clean works better and lasts longer.
S A N I TAT I O N Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor. Cleanliness, top operating efficiency, and appearance of equipment contribute considerably to savory, appetizing foods. Good equipment that is kept clean, works better and lasts longer. Most food imparts its own particular aroma and many foods also absorb existing odors.
SERVICE ED2 Series - Service Views Control Panel Access Switch Thermostat SW-33896 TT-3498 Fuses Switch Thermostat FU-3775 SW-33896 TT-3498 Cutting Board Bracket Indicator Light LI-3027 BT-2342 Indicator Light LI-3027 Control Panel for Model ED2-48 Cable Wrap: Access by removal of bottom panel CB-3045 #868 • ED2 & EU2 Series Operation & Care Manual • 18
SERVICE ED2 Series - Service Views Inside the top - lights Bulb Receptacles LP-3384 (230V) LP-33592 (120/208-240V) RP-3955 (230V) RP-3952 (120/208-240V) The performance of this unit has been optimized using the factory provided bulbs. These bulbs should be replaced with an exact replacement or with a factory recommended replacement. These bulbs have been treated to resist breakage and must be replaced with similarly treated bulbs in order to maintain compliance with NSF standards.
SERVICE ED2 Series - Service Views Lower Door Track ED2SYS-48 - TK-26751 ED2SYS-72 - TK-26753 ED2SYS-96 - TK-26755 Glass Clamp Door Assembly RIGHT-HAND DR-25423 MIDDLE DR-25424 LEFT-HAND DR-25422 ED2SYS-48 - CM-26919 ED2SYS-72 - CM-26920 ED2SYS-96 - CM-26921 End Glass LEFT OR RIGHT GL-25762 End Panel 1005367 Front Glass Handle Bumper Track Bumper BM-24082 ED2SYS-48 - 11088 ED2SYS-72 - 11089 ED2SYS-96 - 11090 ED2SYS-48 - 1001656 ED2SYS-72 - 1001657 ED2SYS-96 - 1001658 #868 • ED2 & EU2 Series Oper
SERVICE Cable Replacement Kits ED2-48 Series Cable Replacement Kit Cable Heating Service Kit No. 4880 includes: CB-3045 Cable Heating Element . . . . . . . . . . . .134 feet CR-3226 Ring Connector . . . . . . . . . . . . . . . . . . . . . . . .4 IN-3488 Insulation Corner . . . . . . . . . . . . . . . . . .1 foot BU-3105 Shoulder Bushing . . . . . . . . . . . . . . . . . . . . . .4 BU-3106 Cup Bushing . . . . . . . . . . . . . . . . . . . . . . . . . .4 SL-3063 Insulating Sleeve . . . . . . . . .
1. BULBS BULBS, 230V RECEPTACLE, BULB RECEPTACLE, BULB, 230V 48 S- SED ED 2S Y Y 2S 48 2ED 2ED Alto-Shaam Part No. Part Description 48 /P 48 /P ED2-48 Series LP-33592 LP-3384 RP-3952 RP-3955 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 2. BUMPER BUMPER END CAP BUMPER TRACK BM-22039 BM-22722 11088 1 2 1 1 2 1 1 2 1 1 2 1 3.
R L ED ED 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 2. BUMPER BUMPER END CAP BUMPER TRACK BM-22039 BM-22722 11089 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 3. CLAMP, GLASS CM-26766 1 1 1 1 1 1 1 1 1001252 1 1 1 1 1 1 1 1 CD-3557 CD-33490 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6.
14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 2. BUMPER BUMPER END CAP BUMPER TRACK BM-22039 BM-22722 11090 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 1 2 1 3.
SERVICE Casters, Plate 1002149 Front Panel 1002681 EU2SYS-48 Front View ED2-48 on BU2-48 Cart with optional casters End Panel 1002016 (2) Shelf, optional 5001430 EU2SYS-48 Rear View ED2-48 on BU2-48 Cart with shelf #868 • ED2 & EU2 Series Operation & Care Manual • 25
Y 2S EU 2S EU Alto-Shaam Part No. BU-3011 1 1 2. BUSHING, SNAP BU-3378 1 1 3. CASTERS, PLATE 1002149 4 4 CD-3607 1 1 5. END PANEL 1002016 2 2 6. FRONT PANEL 1002681 1 1 7. TERMINAL BLOCK 1000623 1 1 L /P /P 72 Y Y Y S- S- 72 ED EU ED 2S 2S 72 SY 2S EU Alto-Shaam Part No. Part Description 72 /P EU2-72 Series S- 4. CORD, 6ft (1828mm) R 1. BUSHING, STRAIN RELIEF 2S Part Description Y S- S- 48 48 /P EU2-48 Series BU-3011 1 1 1 1 2.
#868 • ED2 & EU2 Series Operation & Care Manual • 27
#868 • ED2 & EU2 Series Operation & Care Manual • 28
#868 • ED2 & EU2 Series Operation & Care Manual • 29
#868 • ED2 & EU2 Series Operation & Care Manual • 30
#868 • ED2 & EU2 Series Operation & Care Manual • 31
#868 • ED2 & EU2 Series Operation & Care Manual • 32
#868 • ED2 & EU2 Series Operation & Care Manual • 33
#868 • ED2 & EU2 Series Operation & Care Manual • 34
#868 • ED2 & EU2 Series Operation & Care Manual • 35
T R A N S P O RTAT I O N DAMAGE and CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be established on the part of the shipper. 1. 2.
