Heated Display Cases ® Full Service or Self Service Models: ED2SYS-48 ED2-48; ED2SYS-48 ED2-48/P; ED2SYS-48/P EU2SYS-48; EU2SYS-48/P ED2-48 ED2-72; ED2SYS-72 ED2-72/P; ED2SYS-72/P ED2-72/PL; ED2SYS-72/PL ED2-72/PR; ED2SYS-72/PR ED2SYS-72 EU2SYS-72; EU2SYS-72/P EU2SYS-72/PL EU2SYS-72/PR ED2-96; ED2SYS-96 ED2-96/PL; ED2SYS-96/PL ED2-96/PR; ED2SYS-96/PR ED2SYS-96 EU2SYS-96; EU2SYS-96/P EU2SYS-96/PL EU2SYS-96/PR • INSTALLATION • OPERATION ED2-96 • MAINTENANCE W 1 6 4 N 9 2 2 1 W a t e r S t r e e
® D E L I V E RY U N PA C K I N G This Alto-Shaam appliance has been thoroughly tested and inspected to insure only the highest quality unit is provided. Upon receipt, check for any possible shipping damage and report it at once to the delivering carrier. See Transportation Damage and Claims section located in this manual. This appliance, complete with unattached items and accessories, may have been delivered in one or more packages.
SAFETY PROCEDURES AND PRECAUTIONS Knowledge of proper procedures is essential to the safe operation of electrically and/or gas energized equipment. In accordance with generally accepted product safety labeling guidelines for potential hazards, the following signal words and symbols may be used throughout this manual. Used to indicate the presence of a hazard that will cause severe personal injury, death, or substantial property damage if the warning included with this symbol is ignored.
I N S TA L L AT I O N METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN OPERATION. TO AVOID BURNS, ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. TO PREVENT PERSONAL INJURY, USE CAUTION WHEN MOVING OR LEVELING THIS APPLIANCE. S I T E I N S TA L L AT I O N In order to maintain established National Sanitation Foundation standards, all stationary floor models must be sealed to the floor with a R.T.V. or silastic meeting N.S.F.
I N S TA L L AT I O N S I T E I N S TA L L AT I O N 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER 32-15/16" (837mm) 34-1/4" (870mm) 44-5/16" (1125mm) ED2 PROFILE 27-3/16" (691mm) 26-7/16" (672mm) 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER 47-11/16" (1212mm) ED2SYS-72 ELECTRICAL PANEL ELECTRICAL OUTLET 47-11/16" (1212mm) 20-3/16" (513mm) 26-1/8" (664mm) 48" (1219mm) 47-1/8" (1196mm) 72" (1829mm) ED2SYS-96 3" (76mm) ADJUSTABLE PEGS IN EACH CORNER ELECTRICAL PANEL ELECTRICAL OUTLET 47-11/16" (1212m
I N S TA L L AT I O N S I T E I N S TA L L AT I O N EU2SYS SERIES 5-1/2" (140mm) Swivel Caster 5-1/2" (140mm) EU2SYS-48 32-1/2" (824mm) 48" (1219mm) 5-1/2" (140mm) Rigid Caster Swivel Caster Swivel Caster OPENING HEIGHT (Shown with optional shelf) 28-5/16" (719mm) ELECTRICAL OUTLET OPENING WIDTH OPENING (Shown with optional shelf) 26-1/4" (666mm) 13-5/8" (346mm) OPENING WIDTH OPENING 26-1/4" (666mm) 13-5/8" (346mm) ELECTRICAL PANEL 58-3/16" (1477mm) 31-5/8" (804mm) 26-1/2" (673mm)
I N S TA L L AT I O N ELECTRICAL CONNECTION The appliance must be installed by a qualified service technician. The oven must be properly grounded in accordance with the National Electrical Code and applicable local codes. Plug the unit into a properly grounded receptacle ONLY, positioning the unit so that the plug is easily accessible in case of an emergency. Arcing will occur when connecting or disconnecting the unit unless all controls are in the “ OFF ” position.
I N S TA L L AT I O N ED2 & E D2SYS & EU 2SYS SERIES — OPTIONS & AC CESSORIES DESCRIPTION ED2-48 SERIES ED2-72 SERIES ED2-96 SERIES 5001874 — — ED2-48, -48/P AVAILABLE — — ED2-72, -72/P — 5004182 — ED2-72/PR — 5004183 — ED2-72/PL — 5004184 — ED2-96 — — 5004185 ED2-96/PR — — 5004186 ED2-96/PL — — 5004187 5001143 5001143 5001143 5001281 5001282 5001283 P148 P152 P153 5001293 5001295 5001297 P154 P155 P156 BRUSHED STAINLESS STEEL 5005787 5005789 5005791 CUS
O P E R AT I N G I N S T R U C T I O N S U S E R S A F E T Y I N F O R M AT I O N METAL PARTS OF THIS EQUIPMENT BECOME EXTREMELY HOT WHEN IN TO AVOID BURNS, OPERATION. ALWAYS USE HAND PROTECTION WHEN OPERATING THIS APPLIANCE. The Alto-Shaam heated display case is intended for use in commercial establishments by qualified operating personnel where all operators are familiar with the purpose, limitations, and associated hazards of this appliance.
O P E R AT I N G I N S T R U C T I O N S O P E R AT I N G P R O C E D U R E S 1. DO NOT ADD WATER TO DISPLAY CASE Halo Heat display cases maintain a constant but gentle temperature and eliminate much of the moisture loss associated with conventional display cases. Because of this gentle heat, it is not necessary to add water to the display case. As a matter of fact, adding water is not recommended since water will accelerate the deterioration of the product, and may damage the unit voiding the warranty. 2.
O P E R AT I N G I N S T R U C T I O N S Indicator Lights LI-3027 OR LI-3951 Light Switch SW-33896 Cutting Board Bracket Thermostats TT-3498 BT-2342 Operator/Control side with cutting board Electrical Cord CD-3291 or CD-3557 Thermostat TT-3498 Cutting Board ED2-48, ED2SYS-48 – 4016 (1) ED2-72, ED2SYS-72 – 4017 (1) ED2-96, ED2SYS-96 – 4016 (2) #868 • E D 2 & E U 2 Series Operation & Care Manual • 10 Plug ED2-48 – PG-3337 ED2-72, -96 – PG-3267
O P E R AT I N G I N S T R U C T I O N S PAN CONFIGURATIONS • HEATED DISPLAY CASES 48 Models 5 PAN ZONES 3 PAN ZONES ONE-HALF SIZE PAN FULL-SIZE PAN GN 1/1 GN 1/2 ONE-HALF SIZE PAN GN 1/2 ONE-THIRD SIZE PAN ONE-THIRD SIZE PAN GN 1/3 96 Models 72 Models TWO-THIRDS SIZE PAN 7 PAN ZONES ONE-THIRD SIZE PAN GN 2/3 ONE-THIRD SIZE PAN ONE-THIRD SIZE PAN ONE-THIRD SIZE PAN ONE-THIRD SIZE PAN ONE-THIRD SIZE PAN Four (4) ONE-THIRD SIZE PAN per pan zone.
O P E R AT I N G I N S T R U C T I O N S PAN CONFIGURATIONS • SELF-SERVE HOT DISPLAY CASES ➔ 72 Models (-72/PL & -72/PR) 96 Models (-96/PL & -96/PR) ➔ PAN LAYOUT DIAGRAM 3 PAN ZONES ONE-HALF SIZE PAN ONE-THIRD SIZE PAN TWO-THIRDS SIZE PAN ONE-THIRD SIZE PAN FULL-SIZE PAN ONE-HALF SIZE PAN STANDARD PAN SIZES ➔ Four (4) ONE-THIRD SIZE PANS per pan zone.
O P E R AT I N G I N S T R U C T I O N S 1002585 1000544 1002619 Part No.
O P E R AT I N G I N S T R U C T I O N S GENERAL HOLDING GUIDELINES Chefs, cooks and other specialized food service personnel employ varied methods of cooking. Proper holding temperatures for a specific food product must be based on the moisture content of the product, product density, volume, and proper serving temperatures. Safe holding temperatures must also be correlated with palatability in determining the length of holding time for a specific product.
CARE AND CLEANING C CLEANING AND PREVENTIVE MAINTENANCE PROTECTING STAINLESS STEEL SURFACES CLEANING AGENTS It is important to guard against corrosion in the care of stainless steel surfaces. Harsh, corrosive, or inappropriate chemicals can completely destroy the protective surface layer of stainless steel. Abrasive pads, steel wool, or metal implements will abrade surfaces causing damage to this protective coating and will eventually result in areas of corrosion.
CARE AND CLEANING EQUIPMENT CARE Under normal circumstances, this appliance should provide you with long and trouble free service. There is no preventative maintenance required, however, the following Equipment Care Guide will maximize the potential life and trouble free operation of this appliance. The cleanliness and appearance of this equipment will contribute considerably to operating efficiency and savory, appetizing food. Good equipment that is kept clean works better and lasts longer.
S A N I TAT I O N Food flavor and aroma are usually so closely related that it is difficult, if not impossible, to separate them. There is also an important, inseparable relationship between cleanliness and food flavor. Cleanliness, top operating efficiency, and appearance of equipment contribute considerably to savory, appetizing foods. Good equipment that is kept clean, works better and lasts longer.
SERVICE ED2 Series - Service Views Control Panel Access Switch SW-33896 Thermostat TT-3498 Indicator Light LI-3027 OR LI-3951 Fuses FU-3775 Switch SW-33896 Thermostat TT-3498 Cutting Board Bracket Indicator Light LI-3027 Control Panel for Model ED2-48 OR BT-2342 LI-3951 Cable Wrap: Access by removal of bottom panel 4880 (ED2-48 Series) 4881 (ED2-72 Series) 14228 (ED2-96 Series) #868 • E D 2 & E U 2 Series Operation & Care Manual • 18
SERVICE ED2 Series - Service Views Inside the top - lights Bulb Receptacles LP-33783 (230V) LP-33592 (120/208-240V) RP-3955 (230V) RP-3952 (120/208-240V) The performance of this unit has been optimized using the factory provided bulbs. These bulbs should be replaced with an exact replacement or with a factory recommended replacement. These bulbs have been treated to resist breakage and must be replaced with similarly treated bulbs in order to maintain compliance with NSF standards.
SERVICE ED2 Series - Service Views Upper Door Track ED2SYS-48 - TK-26752 ED2SYS-72 - TK-26754 ED2SYS-96 - TK-26756 Glass Clamp Door Assembly Lower Door Track RIGHT- HAND MIDDLE LEFT- HAND DR-25424 DR-25423 DR-25422 ED2SYS-48 - TK-26751 ED2SYS-72 - TK-26753 ED2SYS-96 - TK-26755 ED2SYS-48 - CM-26765 ED2SYS-72 - CM-26766 ED2SYS-96 - CM-26767 End Glass LEFT OR RIGHT GL-25762 End Panel 1005367 Front Glass, Full Service Handle Bumper Track Bumper BM-24082 ED2SYS-48 - 11088 ED2SYS-72 - 11089 ED2SYS-
SERVICE Cable Replacement Kits ED 2- 48 Series Cab le Rep laceme nt Kit includes: CB-3045 Cable Heating Service Kit No. 4880 Cable Heating Element . . . . . . . . . . . .134 feet CR-3226 Ring Connector . . . . . . . . . . . . . . . . . . . . . . . .4 BU-3105 Shoulder Bushing . . . . . . . . . . . . . . . . . . . . . .4 IN-3488 BU-3106 SL-3063 Insulation Corner . . . . . . . . . . . . . . . . . .1 foot Cup Bushing . . . . . . . . . . . . . . . . . . . . . . . . . .4 Insulating Sleeve . . . . . . .
1. CLAMP, GLASS 5. CORD; 7ft (2133mm) 6. 7. 8. 9. 10. 11. 12.
PART DESCRIPTION 1. PART NO. 120V 230V 120V 230V LP-33592 10 10 10 10 10 10 10 10 LP-33783 10 10 10 10 10 10 10 10 RP-3952 10 10 10 10 10 10 10 10 RP-3955 10 10 10 10 10 10 10 10 GLASS BM-22039 1 1 1 1 1 1 1 1 END CAP BM-22722 2 2 2 2 2 2 2 2 TRACK 11088 1 1 1 1 1 1 1 1 CM-26766 1 1 1 1 1 1 1 1 BULBS RECEPTACLE, BULB 2. BUMPER 3. 4. 5. CLAMP, GLASS 6. CUTTING BOARD 7. 8. 9. 10.
1. BULBS RECEPTACLE, BULB 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12.
SERVICE Casters, Plate 1002149 Front Panel EU2SYS-48 Front View ED2-48 on BU2-48 Cart with optional casters End Panel 1002016 (2) 1002681 Shelf, optional 5005786 EU2SYS-48 Rear View ED2-48 on BU2-48 Cart with shelf #868 • ED 2 & E U 2 S eri es Operation & Care Manual • 25
1 1 BUSHING, SNAP 1 1 CASTERS, PLATE 1002149 4 4 CORD, CD-3607 1 1 FA-3568 1 1 CD-33338 1 1 PANELS 1006857 4 4 TERMINAL BLOCK BK-3023 2 2 FAN FAN CORD 1 1 1 BUSHING, SNAP BU-3378 1 1 1 1 CASTERS, PLATE 1002149 6 6 6 6 CORD, CD-3607 1 1 1 1 1 1 1 1 1 1 1 1 PANELS 1006857 4 4 4 4 TERMINAL BLOCK BK-3023 2 2 2 2 BU-3011 1 1 1 1 BUSHING, SNAP BU-3378 1 1 1 1 CASTERS, PLATE 1002149 6 6 6 6 CORD, CD-3607 1 1 1 1 FA-3568 1
#868 • ED 2 & E U 2 Series Operation & Care Manual • 27
#868 • E D 2 & E U 2 Series Operation & Care Manual • 28
#868 • ED 2 & E U 2 Series Operation & Care Manual • 29
#868 • E D 2 & E U 2 Series Operation & Care Manual • 30
#868 • ED 2 & E U 2 Series Operation & Care Manual • 31
#868 • E D 2 & E U 2 Series Operation & Care Manual • 32
#868 • ED 2 & E U 2 Series Operation & Care Manual • 33
#868 • E D 2 & E U 2 Series Operation & Care Manual • 34
#868 • ED 2 & E U 2 Series Operation & Care Manual • 35
#868 • E D 2 & E U 2 Series Operation & Care Manual • 36
#868 • ED 2 & E U 2 Series Operation & Care Manual • 37
#868 • E D 2 & E U 2 Series Operation & Care Manual • 38
T R A N S P O RTAT I O N DAMAGE and CLAIMS All Alto-Shaam equipment is sold F.O.B. shipping point, and when accepted by the carrier, such shipments become the property of the consignee. Should damage occur in shipment, it is a matter between the carrier and the consignee. In such cases, the carrier is assumed to be responsible for the safe delivery of the merchandise, unless negligence can be established on the part of the shipper. 1. 2. 3. 4. 5. 6. 7. 8.
