Specifications

COMBITHERM CT PROFORMANCE AND CT CLASSIC SERIES • INSTALLATION MANUAL • MN-35947 • 9.
*ELECTRICAL SERVICE CHARGE APPLIES
ELECTRICAL (NO CORD, NO PLUG, DEDICATED CIRCUIT REQUIRED) DO NOT CONNECT TO A G.F.I. OUTLET
WITH COMBISMOKER
®
OPTION
MODEL VOLTAGE PH HZ AWG CONNECTION AMPS kW CONNECTION AMPS kW
CTP6-10E
208 – 240 1* 50/60 6 L1, L2/N, G 51 – 59 10.7 – 13.8 L1, L2/N, G 53.5 – 62 11.2 – 14.5
208 – 240 3 50/60 8 L1, L2, L3, G 35 – 40 10.7 – 13.8 L1, L2, L3, G 37.5 – 43 11.2 – 14.5
380 – 415 3 50 8 L1, L2, L3, N, G 35 – 37 11.9 – 13.8 L1, L2, L3, N, G 37.6 – 40 12.5 – 14.5
440 – 480 3* 50/60 10 L1, L2, L3, G 22 – 24 11.9 – 13.8 L1, L2, L3, G 23.3 – 25.5 12.5 – 14.5
WEIGHT SHIP DIMENSIONS PAN CAPACITY
NET 524 lbs est 238 kg
(L x W x H) 56" x 45" x 51"*
FULL–SIZE: 20" x 12" x 2-1/2" Six (6)
PRODUCT MAXIMUM: 72 lb (33 kg)
SHIP 574 lbs* 260 kg* (1422 x 1143 x 1295mm)*
GN 1/1: 530 x 325 x 65mm Six (6)
VOLUME MAXIMUM: 45 quarts (57 liters)
*
DOMESTIC GROUND SHIPPING INFORMATION . CONTACT FACTORY FOR
EXPORT WEIGHT AND DIMENSIONS .
*HALF–SIZE SHEET: 18" x 13" x 1" Six (6)
*ADDITIONAL WIRE SHELVES REQUIRED FOR
MAXIMUM CAPACITY
*ON WIRE SHELVES ONLY
WATER REQUIREMENTS WATER QUALITY STANDARDS
TWO (2) COLD WATER INLETS - DRINKING QUALITY
ONE (1) TREATED WATER INLET: 3/4" NPT*
ONE (1) UNTREATED WATER INLET: 3/4" NPT*
LINE PRESSURE: 30 to 90 psi 2.1 to 6.3 bar
WATER DRAIN:
1-1/2" CONNECTION WITH A 2" MINIMUM AIR GAP INSTALLED AS CLOSE TO THE OVEN AS
POSSIBLE. MATERIALS MUST WITHSTAND TEMPERATURES UP TO 200°F (93°C).
It is the sole responsibility of the owner/operator/purchaser of this equipment
to verify that the incoming water supply is comprehensively tested and if
required, a means of “water treatment” provided that would meet compliance
requirements with the published water quality standards published below.
Non-compliance with these minimum standards will potentially damage this
equipment and/or components and VOID the original equipment manufacturer’s
warranty. Alto-Shaam recommends using OptiPure
®
[www.optipurewater.com]
products to properly treat your water.
CLEARANCE REQUIREMENTS
Contaminant
Free Chlorine
Hardness
Chloride
pH
Silica
Total Dissolved Solids (tds)
Inlet Water Requirements
Less than 0.1 ppm (mg/L)
30-70 ppm
Less than 30 ppm (mg/L)
7.0 to 8.5
Less than 12 ppm (mg/L)
50-125 ppm
LEFT: 0" (0mm) 18" (457mm)
FOR SERVICE ACCESS
RIGHT: 0" (0mm) NON-COMBUSTIBLE SURFACES 2" (51mm) COMBUSTIBLE SURFACES
TOP: 20" (508mm) FOR AIR MOVEMENT
BACK: 4" (102mm) BOTTOM: 5-1/8" (130mm) FOR LEGS, AIR INTAKE
INSTALLATION REQUIREMENTS
• Oven must be installed level. • Hood installation is required.
• Water supply shut-off valve and back-flow preventer when required by local code.
* Can manifold off of one
3/4" line.
DIMENSIONS: H x W x D
EXTERIOR:
34-1/2" x 35-11/16" x 41-7/16" (876mm x 906mm x 1053mm)
EXTERIOR WITH RECESSED DOOR:
34-1/2" x 39-11/16" x 41-7/16" (876mm x 1008mm x 1053mm)
INTERIOR:
20-1/2" x 16-1/4" x 28-1/16" (520mm x 411mm x 712mm)
35-11/16" (906mm)
26-3/16" (665mm)
NOTES:
ALL DIMS DISPLAYED AS H x W x D
6.10es2
805601
34-1/2" (876mm)
60-9/16" (1538mm)
39-1/4" (996mm)
4-1/2" (114mm)
4-1/4" (108mm)
6-11/16" (168mm)
28-13/16" (731mm)
C - at bottom
of oven
A, B, D
41-7/16" (1053mm)
INTERIOR DIMENSIONS: 520mm x 411mm x 712mm
EXTERIOR DIMENSIONS: 886mm x 907mm x 995mm
6.10 ELEC OVER 6.10 ELEC: 1772mm x 907mm x 995mm
6.10 ELEC OVER 10.10 ELEC: 1850mm x 907mm x 995mm
6.10 ELEC OVER 7.14 ELEC: 1954mm x 1111mm x 1150mm
6.10 ELEC OVER 10.18 ELEC: 1850mm x 1111mm x 1150mm
6.10 ELEC OVER ASC-4E: 1877mm x 1111mm x 1182mm
6.10 ELEC ON 28" STAND: 1727mm x 907mm x 995mm
2-5/16" (58mm)
3-5/16" (84mm)
5-1/4" (134mm)
12" (305mm)
17-11/16" (450mm)
A= UNTREATED WATER
B= TREATED WATER
C= ELECTRICAL
D= WATER DRAIN
5-1/4" (134mm)
12" (305mm)
17-11/16" (450mm)
1-11/16" (42mm)
A
B
C
D
A
B
D
3-11/16" (93mm)
CTP6-10E
El Ectric boilEr-frEE