User`s guide

INTERFACES
9
ACCESSORIES 8
Model No. Description
RACK MOUNT ACCESSORIES
DA1293SX
Rack/Wall Shelf fits two MX2100AV
units side by side
DA1294SX
Rack/Wall mount ears for single
MX2100AV
TABLE MOUNT BRACKETS
TM1271
1U High, ½ Rack-Wide
TM1272
1U High, ½ Rack-Wide with 15-pin
HD connector plate
TM1273
1U High, ½ Rack-Wide with snap-in
connectors
TM1274
1U High, ½ Rack-Wide with snap-in &
POWER connectors
Table 7. Rack Mount Accessories
Model No. Description
INPUT/LOCAL MONITOR CABLES
MS8121CA/
MS8151CA/
MS861CA
MAC Local Monitor Cable
MS8122CA/
MS8152CA/
MS8162CA
MAC Input Cable
MS8123CA/
M18153CA/
MS8163CA
SUN/SGI Local Monitor Cable
MS8124CA/
MS8154CA/
MS8164CA
SUN/SGI Input Cable
MS8125CA/
MS8155CA/
MS8165CA
VGA Local Monitor Cable
MS8126CA/
MS8156CA/
MS8166CA
VGA Input Cable
MS8129CA/
MS8159CA/
MS8169CA
5 BNC Input/Local Monitor Cable
4 BNC TO 4 BNC COAXIAL CABLE
CB4103MR
3 feet, 4 BNC to 4 BNC coaxial cable
CB4106MR
6 feet, 4 BNC to 4 BNC coaxial cable
CB4112MR
12 feet, 4 BNC to 4 BNC coaxial
cable
CB4125MR
25 feet, 4 BNC to 4 BNC coaxial
cable
CB4150MR
50 feet, 4 BNC to 4 BNC coaxial
cable
CB4175MR
75 feet, 4 BNC to 4 BNC coaxial
cable
CB41100MR
100 feet, 4 BNC to 4 BNC coaxial
cable
CB41150MR
150 feet, 4 BNC to 4 BNC coaxial
cable
5 BNC TO 5 BNC COAXIAL CABLE
CB4203MR
3 feet, 5 BNC to 5 BNC coaxial cable
CB4206MR
6 feet, 5 BNC to 5 BNC coaxial cable
CB4212MR
12 feet, 5 BNC to 5 BNC coaxial
cable
CB4225MR
25 feet, 5 BNC to 5 BNC coaxial
cable
CB4250MR
50 feet, 5 BNC to 5 BNC coaxial
cable
CB4275MR
75 feet, 5 BNC to 5 BNC coaxial
cable
CB42100MR
100 feet, 5 BNC to 5 BNC coaxial
cable
CB42150MR
150 feet, 5 BNC to 5 BNC coaxial
cable
Table 8. Input and Output Cables
Input cable Local Monitor Cables and Output
Cables must be ordered separately from following
list.
TROUBLESHOOTING GUIDE 9
• Make sure that the LED located on the front
panel lights RED when power is connected or
GREEN when a signal is connected to any
input of the MX2100AV.
• Make sure that the cables have the correct pin-
outs and the connection and quality of the
cables are good.
• Make sure that the source and display are
scan-rate compatible. The projector or monitor
should support an appropriate signal format
(RGsB, RGBS or RGBHV). Connect a projector
or monitor directly to the computer with a
shorter cable to verify the compatibility of the
display and source.
• Make sure that the POWER UP DEFAULT
switches are properly set according to Table 6.