MULTI-TASKER™ MT103-127 MT103-128 MANUAL PART NUMBER: 400-0390-002 MT103-127/128 VGA TO 5 BNC LINE DRIVER/INTERFACE AND VGA TO 3 BNC LINE DRIVER/INTERFACE/BUFFERED LOOP CARDS FOR MULTI-TASKER USER’S GUIDE
MULTI-TASKER™ TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS.............. 2 GENERAL ................................ ......................... 2 INSTALLATION ................................ ................. 2 CLEANING ................................ ........................ 2 FCC / CE NOTICE................................ ............. 2 ABOUT YOUR MT103-127/128 ........................... 3 TECHNICAL SPECIFICATIONS .......................... 3 PRODUCT DESCRIPTION................................
MULTI-TASKER™ PRECAUTIONS / SAFETY WARNINGS 1 • This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
MULTI-TASKER™ ABOUT YOUR MT103-127/128 2 TECHNICAL SPECIFICATIONS MT103-127/128 FEATURES/ DESCRIPTION GENERAL Inputs Outputs MT103-127 VGA TO 5 BNC LINE DRIVER / INTERFACE VGA TO 3 BNC LINE DRIVER / INTERFACE / BUFFERED LOOP MT103-128 The MT103-127/128 are high-resolution interfaces designed to connect a computer video source to a compatible monitor or projector over long distances. The MT103-127/128 are compatible with VGA thru UXGA resolutions.
MULTI-TASKER™ PRODUCT DESCRIPTION 4 DESCRIPTION 2: MT103-128 DESCRIPTION 1: MT103-127 4
MULTI-TASKER™ APPLICATION DIAGRAM 5 DIAGRAM 1: MT103-127 TYPICAL SETUP DIAGRAM 2: MT103-128 TYPICAL SETUP 5
MULTI-TASKER™ DIAGRAM 3: MT103-127 INTERNAL VIEW 6
MULTI-TASKER™ DIAGRAM 4: MT103-128 INTERNAL VIEW 7
MULTI-TASKER™ DIAGRAM 5: MT103-127 SETTINGS MT103-127 SWITCH LOCATIONS AND SETTINGS DEFAULTS: Horizontal Position = Hardware Control Equalization = Hardware Control Composite Sync = OFF (Closed) Sync Delay = ON Sync On Green = OFF 8
MULTI-TASKER™ DIAGRAM 6: MT103-128 SETTINGS MT103-128 SWITCH LOCATIONS AND SETTINGS DEFAULTS: Horizontal Position = Hardware Control Equalization = Hardware Control Sync Delay = ON 9
MULTI-TASKER™ INSTALLING YOUR MT103-127/128 6 OPERATION Step 1. Determine the switch settings before installing the MT103-127/128. The switch settings determine the following: 7.1 RS-232 CONTROL When used in the Multi-Tasker™ Enclosure, the MT103-127/128 has many advanced remote control capabilities, which are accessible through standard RS-232 communication. The act ual controlling can be accomplished through a computer control system or any other device capable of sending RS -232 commands.
MULTI-TASKER™ The Card ID is an assigned value. It is equal to the enclosure slot number in which the card is installed. The value can range from 1 to 4 up to 1 to 20 depending on the enclosure. 2. [C] This command displays the card status. Command Format: [CnUi] Cn = Card ID (n = # from 1 to max slots) Card ID 0 (C0) is used for the controller. See the MT100-100 User’s Guide for details.
MULTI-TASKER™ Example: Feedback Prefix Definitions: +MT = Multi-Tasker Card +VR = Firmware Version +ON = ON/OFF Status +EQ = Equalization Setting +SI = Signal Present Send the command [CLRC4] to restore the card in slot #4 to its factory defaults. Send the command [C4] after the [CLR] command the receive the following feedback: ON,EQ=0,HP=10 C04 Example 1: 5. [?] Command = Feedback = +EQ 25 C04 This command will return general information about the card and the status.
MULTI-TASKER™ SET AN ABSOLUTE VALUE 10. [SIG] Command Format: [EQ=mCnUi] The Signal Present command tests for the presence of an input signal. The card returns either a "1" or a "0" as feedback. m = EQ Value (m = # from 0 to 50) Cn = Card ID (n = slot # from 1 to max slots) 1 = Signal detected 0 = No signal detected Ui = Unit ID (i = # from 0 to 9) Command Format: [SIGCnUi] Example: Cn = Card ID (n = # from 1 to max slots) Send the command [EQ=25C4] to set the equalization value to 25.
MULTI-TASKER™ In Multi-Tasker™ systems with audio and video cards, boards are typically grouped as follows: 13. [ + ] and [ – ] These commands are used to adjust the Equalization and Horizontal Position and may be used from keyboard commands or programmed front panel buttons. Group 1 = Video Cards Group 2 = Audio Cards Group 3 = Video and Audio Cards If assigning group commands to button functions, it is best to use the "Press and Hold on Power Up" to make group settings.
MULTI-TASKER™ 17. [RD] 7.3 SUMMARY OF COMMANDS This command displays the members in each group.
MULTI-TASKER™ 7.4 MENU MODE 7.4.2 USING MENU MODE MENU MODE commands are RS-232 commands that allow virtually the same functionality as programming commands. Unlike the programming commands in the previous sections, 7.2 and 7.3, MENU commands prompt the user to select from a list of available options. The system then responds based upon selections made by the user. SUGGESTION: Before using the menu mode, it is best to disable the automatic feedback feature.
MULTI-TASKER™ 8. Read each menu carefully, and continue selecting keys as prompted for further functions. (Example prompt: "Key= ") MT103-127/128 MAIN MENU PRESS KEY TO SELECT 1: CONTROL 2: SETUP 3: STATUS 4: HELP ESC: GO BACK 7.4.3 MENU TYPES 1. MAIN MENU The first menu displayed after selecting the card is the Main Menu. This menu provides access to the main functions related to the card. Press the key representing the menu item for access. A sub menu will appear next. 2.
MULTI-TASKER™ 3: STATUS Equivalent to the [VER] and [C] commands. Returns the card number, firmware revision and status. 4: HELP Equivalent to the [HELP] command. Displays a list of commands available for the MT103-127/128 along with a brief description. ESC Returns to the parent menu. 3. Display Card Status Starting from the keystrokes below.
MULTI-TASKER™ ALTINEX POLICY 9 9.1 LIMITED WARRANTY/RETURN POLICY Please see the Altinex website at www.altinex.com for details on warranty and return policy. 9.2 CONTACT INFORMATION ALTINEX, INC 592 Apollo Street Brea, CA 92821 USA TEL: 714 990-2300 TOLL FREE: 1-800-ALTINEX WEB: www.altinex.com E-MAIL: solutions@altinex.
