User`s guide

MT
MTMT
MT103
103103
103-
--
-102
102102
102 User’s Guide
400-0107-006
11
Group Commands
Group commands allow several cards to be controlled simultaneously with
a single command. Up to 8 groups (G1-G8) may be defined. These
commands apply to all cards, not only the MT103-102.
23. [WR]
This command adds cards to a group. In MultiTasker systems with
audio and video cards, the groups are typically as follows:
Group 1 = Video Cards
Group 2 = Audio Cards
Group 3 = Video and Audio Cards
Command Format: [WRCn 1 Cn 2 …Gk]
Cn = Card ID (n = slot # from 1 to max slots)
Gk = Group ID (k = # from 1-8)
Example:
Add C2, C4, and C6 to G5 by sending the command [WRC2C4C6G5].
After executing this command, G5 will consist of C2, C4, and C6.
Now add C8 to G5 by sending [WRC8G5]. C8 is added to G5, and G5
is not overwritten. View the contents of G5 by sending [RDG5] and
receiving the following feedback:
[G5=C2C4C6C8]
24. [RMC]
This command removes one or more cards from a group.
Command Format: [RMCn 1 Cn 2 …Gk]
Cn = Card ID (n= # from 1 to max slots)
Gk = Group ID (k = # from 1-8)
Example:
G5 consists of C2, C4, C6, and C8. Remove C6 and C8 by sending
[RMC6C8G5]. View the contents of G5 by sending [RDG5] and
receiving the following feedback:
[G5=C2C4]
25. [RMG]
This command deletes one or all groups.
Command Format: [RMGk]
Gk = Group ID (k = # from 1-8, * for all)
Example:
Remove all cards from G5 by sending [RMG5]. The system will return
the following feedback:
[G5=0]
Example 2:
Remove all cards from all groups, effectively deleting all groups, by
sending [RMG*]. The system will return the following feedback:
G1-G8: EMPTY
26. [RD]
This command reads and then displays the members in a group.
Command Format: [RDGk]
Gk = Group ID (k = # from 1-8)
Example:
C2, C4, and C6 make up G5. Read the member data for G5 by sending
the command [RDG5]. The system will return feedback as follows:
[G5=C2C4C6]
The feedback shows G5 and then the cards that make up G5. In this
case, G5 includes C2, C4, and C6.
7.3. Summary of Commands
Basic Commands
Basic CommandsBasic Commands
Basic Commands
1)
1)1)
1) [VER]
[VER][VER]
[VER] Display firmware version
Display firmware versionDisplay firmware version
Display firmware version
2)
2)2)
2) [C]
[C][C]
[C] Display card status
Display card statusDisplay card status
Display card status
3)
3)3)
3) [CnS]
[CnS][CnS]
[CnS] Save settings (MT103
Save settings (MT103Save settings (MT103
Save settings (MT103-
--
-102 only)
102 only)102 only)
102 only)
4)
4)4)
4) [..S]
[..S][..S]
[..S] Save this setting (MT103
Save this setting (MT103Save this setting (MT103
Save this setting (MT103-
--
-102 only)
102 only)102 only)
102 only)
5)
5)5)
5) [TEST]
[TEST][TEST]
[TEST] Test internal memory ICs
Test internal memory ICsTest internal memory ICs
Test internal memory ICs
6)
6)6)
6) [HELP]
[HELP][HELP]
[HELP] Display available commands
Display available commandsDisplay available commands
Display available commands
Fe
FeFe
Feedback Commands
edback Commandsedback Commands
edback Commands
7)
7)7)
7) [FBD]
[FBD][FBD]
[FBD] Feedback delay on/off
Feedback delay on/offFeedback delay on/off
Feedback delay on/off
8)
8)8)
8) [?]
[?][?]
[?] Display system cards
Display system cardsDisplay system cards
Display system cards
9)
9)9)
9) [?C]
[?C][?C]
[?C] Display card information
Display card informationDisplay card information
Display card information
10)
10)10)
10) [STA1]
[STA1][STA1]
[STA1] Auto
AutoAuto
Auto-
--
-feedback on
feedback onfeedback on
feedback on
11)
11)11)
11) [STA0]
[STA0][STA0]
[STA0] Auto
AutoAuto
Auto-
--
-feedback off
feedback offfeedback off
feedback off
12)
12)12)
12) [...F]
[...F][...F]
[...F] Display OK after command
Display OK after commandDisplay OK after command
Display OK after command
Card Control Commands (MT103
Card Control Commands (MT103Card Control Commands (MT103
Card Control Commands (MT103-
--
-102 only)
102 only)102 only)
102 only)
13)
13)13)
13) [SIG]
[SIG][SIG]
[SIG] Test f
Test fTest f
Test for a signal
or a signalor a signal
or a signal
14)
14)14)
14) [ON]
[ON][ON]
[ON] Enable one or more outputs
Enable one or more outputsEnable one or more outputs
Enable one or more outputs
15)
15)15)
15) [OFF]
[OFF][OFF]
[OFF] Disable one or more outputs
Disable one or more outputsDisable one or more outputs
Disable one or more outputs
16)
16)16)
16) […P]
[…P][…P]
[…P] Sets the path, [SW] preload
Sets the path, [SW] preloadSets the path, [SW] preload
Sets the path, [SW] preload
17)
17)17)
17) [SW]
[SW][SW]
[SW] Switch preloaded outputs
Switch preloaded outputsSwitch preloaded outputs
Switch preloaded outputs
ID Commands
ID CommandsID Commands
ID Commands
18)
18)18)
18) [RSI]
[RSI][RSI]
[RSI] Reset Card IDs to defaults
Reset Card IDs to defaultsReset Card IDs to defaults
Reset Card IDs to defaults
19)
19)19)
19) [SIDn]
[SIDn][SIDn]
[SIDn] Set all Card IDs
Set all Card IDsSet all Card IDs
Set all Card IDs
20)
20)20)
20) [SIDnCi]
[SIDnCi][SIDnCi]
[SIDnCi] Set one C
Set one CSet one C
Set one Card ID
ard IDard ID
ard ID
21)
21)21)
21) [SID+]
[SID+][SID+]
[SID+] Set all Card IDs to an offset
Set all Card IDs to an offsetSet all Card IDs to an offset
Set all Card IDs to an offset
22)
22)22)
22) [RSN]
[RSN][RSN]
[RSN] Display card slot number
Display card slot numberDisplay card slot number
Display card slot number
Group Commands
Group CommandsGroup Commands
Group Commands
23)
23)23)
23) [WR]
[WR][WR]
[WR] Add card(s) to a group
Add card(s) to a groupAdd card(s) to a group
Add card(s) to a group
24)
24)24)
24) [RMC]
[RMC][RMC]
[RMC] Remove card(s) from group
Remove card(s) from groupRemove card(s) from group
Remove card(s) from group
25)
25)25)
25) [RMG]
[RMG][RMG]
[RMG] Delete group
Delete groupDelete group
Delete group
26)
26)26)
26) [RD]
[RD][RD]
[RD] Display group members
Display group membersDisplay group members
Display group members