Install guide

ManualsBrandsAltigen ManualsConsumer electronicsAT510

Universal Quick Install Guide

Quantum and Triton Boards

Use this guide to install Quantum boards and Triton class telephony boards,

including Triton VoIP, Triton Analog Extension, Triton Analog Trunk (LS and LS/

GS), Triton Resource, Triton T1/PRI, Triton T1/E1 PRI, and Triton 30-Party

MeetMe, all of which have common installation procedures.

All Triton PCI Family and Quantum Boards

Note: In systems with over 12 boards installed, use the 10-connector side of the

ribbon cable on the short end and use the 12-connector side of the ribbon

cable on the long end. Starting with the innermost connectors, connect the

boards, leaving a minimum of 3 connectors hanging off each end.

Supported Board/Software Guidelines

Board

4.5

OE/ACC/

ACM/HPBX

4.6

OE/ACC/

ACM 5.0/

5.0A

OE/ACC/ACM/

HPBX 5.0A

Update 2 & 3

OE/ACC/ACM/

HPBX 5.0A

Update 4 & up

ACC/ACM

5.1

Quantum Yes Yes Yes Yes Yes Yes

Triton Analog Extension Yes Yes Yes Yes Yes Yes

Triton Analog Extension B No No No No Yes Yes

Triton Analog Trunk-12 Yes Yes Yes Yes Yes Yes

Triton Analog Trunk-8 No No No Yes Yes Yes

Triton T1/PRI Yes Yes Yes Yes Yes Yes

Triton T1/E1 PRI Yes Yes Yes Yes Yes Yes

Triton VoIP-30 Yes Yes Yes Yes Yes Yes

Triton VoIP-8 Yes Yes Yes Yes Yes Yes

Triton Resource Yes Yes Yes Yes Yes Yes

Triton 30-Party MeetMe No No No No No Yes

MVIP BUS Termination Switch

Board Silhouette

Power Cable

MVIP Connector

Summary of content (6 pages)

PAGE 1
Universal Quick Install Guide Quantum and Triton Boards Use this guide to install Quantum boards and Triton class telephony boards, including Triton VoIP, Triton Analog Extension, Triton Analog Trunk (LS and LS/ GS), Triton Resource, Triton T1/PRI, Triton T1/E1 PRI, and Triton 30-Party MeetMe, all of which have common installation procedures.
PAGE 2
Installation Notes • Observe proper board handling procedures (refer to AltiGen Field Alert #67). • Pre-installation of boards is recommended over on-site installations. • Although boards are factory tested prior to shipping, it is recommended that you follow a burn-in period of approximately 12 hours minimum before an on-site deployment. • Always observe personal safety procedures.
PAGE 3
Connection Options There are 3 connection options for connecting Quantum/Triton boards to trunks and extensions: 1. 12 Ports Bridging Adapter 2. 66 Punch Down Block with 50-Pin Telco Female Connector 3.
PAGE 4
Installation Instructions (It is assumed that the server operating system, AltiWare, and its corresponding licenses are already installed.) 1. Ensure that the chassis power switch is in the OFF position and the power cord is unplugged before removing the chassis cover. 2. Slide the board into the board guide on the chassis, then firmly seat the board into the slot. 3. Screw the board down to the chassis for support. 4.
PAGE 5
13. If the test fails, check MVIP connections and troubleshoot accordingly. If there are any failures, note the board(s) and use the following steps to troubleshoot the MVIP connection: (System shutdown is not necessary for MVIP troubleshooting unless replacing a board.) • Remove the MVIP cable from all boards and check the MVIP connector on the boards for bent or pushed down pins.
PAGE 6
Technical Support End users Contact your authorized AltiGen Dealer. Authorized AltiGen Dealers Call AltiGen Technical Support at 510-252-9712 Submit a case on the authorized dealer web site: https://dealer.altigen.