Specifications
Table Of Contents
- Preface: About This Manual
- Overview
- Key AltiContact Manager Characteristics
- Call Center/IP PBX Features
- Automatic Call Distribution Features
- IVR Features
- AltiGen Voice Mail Features
- Internet Integration Features
- System Administration Features
- T1/PRI/E1 Features
- Voice over IP Features
- Voice over IP Session Support AltiContact Manager Features
- AltiWare Tools
- Optional Add-On Software
- Optional Add-On Products
- Optional Kits
- Key AltiContact Manager Characteristics
- System Requirements
- Hardware Requirements
- System Key Requirement
- Selecting the AltiContact Manager Platform
- Minimum System Requirements
- Proper Grounding and Loop Current
- Uninterruptible Power Supply (UPS)
- Operating Environment
- AltiGen Telephony Boards
- Functional Specifications
- AltiGen Board Installation
- AltiGen Board Options
- System Limitations
- Power Requirements
- Heat Factor
- Installing a Cooling Fan
- Proper Board Handling Procedures
- Electrostatic Discharge (ESD) Warning
- Operating Environment
- Packaging for Shipment and Storage
- AltiContact Manager Conference Resource Limits
- Software Installation
- Software License Activation and Registration
- New Installation
- Upgrading AltiWare OE
- License Activation and Registration Process
- Online License Registration Procedures
- Manual Online License Registration Procedure
- Offline Registration Procedures
- Windows Emergency Repair Disk
- Installing ACM Administrator on Remote Systems
- Running ACM Administrator
- Shutting Down AltiContact Manager when Changing or Adding Hardware
- Transferring the AltiContact Manager to Another Server Chassis
- AltiContact Manager Uninstall
- Software Installation Troubleshooting
- Getting Around ACM Administrator
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Using a Tenant Table
- Country Relevant
- CT-Bus Clock Configuration
- Audio Peripheral Configuration
- Board Configuration
- Trunk Configuration
- Voice Mail Configuration
- VoIP Configuration
- Defining an IP Dialing Table
- Setting VoIP Codecs
- Network Configuration Guidelines for VoIP
- Network Configuration Guidelines for the Alti-IP 600
- Configuration Guidelines for NAT
- Firewall Considerations
- Setting up H.323 Traffic Forwarding for H.323 NAT
- Setting Up an AltiContact Manager-to- AltiContact Manager IP Network
- Out Call Routing Configuration
- IVR Configuration
- CallCenter Configuration
- Agent Configuration
- Huntgroup Configuration
- Workgroup Configuration
- Setting Up IP Extensions
- Alti-IP 600 Phone Configuration
- Application Extension Configuration
- System Data Management
- System Report Management
- Data and Internet Integration
- AltiWeb
- Using TAPI
- Tools
- Basic Call Router & Call Router Advanced
- Call Accounting Report Formats
- E1 R2 CAS Installation
- Product Repair Services & Technical Support
- Glossary
- Index
- Readers Comment Form
System Requirements
AltiContact Manager Administration Manual 2-5
2. System
Requirements
The I/O switch is factory preset as shown below. Change this setting only
if there is a hardware conflict.
The Quantum telephony board has the following functional characteristics:
• MVIP compatible
• 256 Port Non-Blocking Switch Matrix
• Audio Peripheral Input & Output
• Jumper-Free Configuration
• On-Board Telephony Power Supply for Quantum D Board
• Automatic Power Failure Transfer
•ISABus
Triton Analog Extension Board
The Triton Analog Extension telephony board has a dedicated voice
channel for every extension port and FSK-only message waiting
.
The Triton Analog Extension telephony board has the following functional
characteristics:
LED Indicators
LED 1B LED 1A Status
ON ON 5V is OK; 12V is OK – normal operation
OFF OFF Power cable not plugged in
ON OFF 5V less than 4.5V but more than 3V – bad PC 5V
power
OFF ON 12V less than 9V – bad PC 12V power
LED 2, located near the 12V connector, is a red LED for diagnostic purposes. If
it is ON, the fuse is blown.