User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
36 AltiWare ACC 5.1 Administration Manual
Copy activation file failed. Activation file (exctl) is not in the
specified folder, is missing, or is
corrupted. Make sure you select the
correct file folder where the activation
file is located and try again. If problem
persists, you can manually copy the
activation file to c:\AltiServ\db
directory (if AltiServ is installed on the
c: drive) and run the installation
program again.
An error occurred during the move
data process.
Make sure all AltiGen applications and
services are stopped/closed before
installing AltiWare.
Setup cannot detect your system key.
You must plug your system key into
either a parallel or USB port for
upgrading to AltiWare.
Make sure your system key is fully
inserted into your parallel or USB port
prior to installing AltiWare. If error
persists, reboot the system, then run
setup again.
Setup has not detected your system
key. If you proceed the installation
WITHOUT the system key, only 8
physical ports will be available for use
after the AltiWare installation.
Make sure your system key is fully
inserted into your parallel or USB port
prior to installing AltiWare.
Setup cannot append the AltiWare
path because your existing system
environment is too long. You must
manually append the AltiWare path to
your system environment path after
finishing AltiWare’s installation but
before restarting your system. You
can find the system environment path
through Control Panel > System >
Environment > Path.
Manually append c:\AltiWare\exe (if
AltiWare is installed on c: drive) to
your system environment path
(through Control Panel > System >
Environment > Path) after finishing
AltiWare’s installation but before
restarting your system.
Unable to add AltiWare path to the
system.
Manually append c:\AltiWare \exe (if
AltiWare is installed on c: drive) to
your system environment path
(through Control Panel > System >
Environment > Path) after finishing
AltiWare’s installation but before
restarting your system
Failed to upgrade AltiWare
databases.
The previous database may be
corrupted. Restore the last, known
working database and try again. If
error persists, contact your Authorized
AltiGen Dealer.
Error Message Solution