User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
Chapter 17: Mobile Extension Configuration
AltiWare ACC 5.1 Administration Manual 245
Figure 6. Mobile Trunks dialog box
• In the Phrase panel, you have three options: You can select either Press Any
Key To Answer Call or Play Phrase After Answered. And you can select
Play Phrase Before Dial Tone. You can use the Apply button to apply
selections in this panel to other mobile extensions.
• Press Any Key To Answer Call—when a call is answered by this mobile
extension user, the system will play the following phrase for the mobile
extension user: “To accept this call, please press any digit.” The user must
press any key within 3 seconds to connect the call; otherwise, it will time out
and the call will be treated as an agent/extension RNA and will be routed
according to its workgroup/extension setting.
If there is a network error or a mobile extension trunk is not available, RNA
handling is applied to the caller. Therefore, it is suggested that you don’t
check the Set RNA Agent Logout option for the group that contains the
mobile extension as an agent (Workgroup Configuration, Call Handling
tab).
• Play Phrase After Answered—the system will play the given phrase when
the mobile extension user answers the call from the system. The default
phrase (9037) is a special tone to signal the mobile extension user that this
call can be put on hold, parked, transferred, conferenced.
• Play Phrase Before Dial Tone—the system will play the default phrase
9037 (a special tone) and then the dial tone when the mobile extension user
calls into the system through a configured DNIS Access Number.
5. In the Boards view of AltiWare Administrator, double-click the MobileExt board. A
Board Configuration dialog box opens.
6. In the Board Configuration dialog box, double-click the channel group (on the right-
hand side). The following dialog box opens: