User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
Chapter 9: AltiGen IP Phone Configuration
AltiWare ACC 5.1 Administration Manual 165
Debug
This is for debugging the IP phone using Telnet. You need to
enter a Diagnostic password when logging in to AltiWare Admin
(before you enter your Admin password) to enable this
configuration.
Time
Display
• Offset—a per phone-based configuration that allows a
remote IP phone to display a different time, based on
location. The offset is the time difference, in hours, between
the AltiGen system and the IP phone.
• Format—a per-phone-based configuration that allows the
IP phone to display the time in one of the following formats:
24 hour (example: 13:15), 12 hour AM/PM (example: 1:15
PM), or AM/PM 12 hour (example: PM 1:15).
TFTP
Lets you assign the TFTP server to which the IP phone can
connect for updating firmware when necessary. Enter the IP
address of the TFTP server in the Server field.
To reset the phone and download the latest firmware image,
check the Reset IP Phone and Boot Download check boxes.
If you only check the Boot Download box, the firmware will
be downloaded when the IP phone reboots (power cycles) next
time.
Note: Make sure the TFTP server is running and the new
firmware image is loaded to the correct directory before
you reset and download firmware.
NAT
Setting
This setting is for a remote IP phone with a private address and
behind NAT. When connecting to the AltiGen system, the
system will use this information to execute the NAT traversal
for the IP phone. The NAT status and address are read-only
fields.
• NAT Status—Indicates if the IP phone is behind a NAT
router. Read only.
• NAT Address— This is the NAT router’s public IP address,
as set in the Extension Configuration window. Read only.
Registry Keep-Alive Duration—Indicates how often a SIP
registration message is sent to the server when the IP phone
is behind a NAT router. You need to enter a Diagnostic
password when logging in to AltiWare Admin (before you
enter your Admin password) to enable this configuration.
Default setting is 60 seconds.
• TOS—
Parameter Description