User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
136 AltiWare ACC 5.1 Administration Manual
Phone Display Options
For analog and IP phones, the administrator can select what information is to be
displayed.
Depending on the number of display lines on the LCD, the phone can be set up to show
two lines of specific caller information on the display.
In the Phone Display field, use the Number Line and Name Line drop-down lists to
select the caller information to display:
• Caller Number
• Caller Name
• DNIS Number
• DNIS Name
• IVR Data
• User Data
Note: For most phones, the number line can only display a number. If the Number Line
is set to Caller Name, DNIS Name, User Data or AA Data, the phone may
display “Unknown” on the number line.
Alti-IP 600 and IP 705 Phone Display Notes
For the Alti-IP 600 and IP 705, the Name Line displays caller information under the
following conditions:
• If Name Line is set to Caller Name, it will display caller name. If there is no name
information, the number will be displayed.
• If Name Line is set to Caller Number, it will display the caller number. If there is
no number information, “Unknown” will be displayed.
• If Name Line is set to DNIS Name, it will display DNIS name. If there is no name
information, the DNIS number will be displayed.
• If Name Line is set to DNIS Number, it will display the DNIS number. If there is
no number information, “Unknown” will be displayed.
Configuring Group Options for an Extension
In the Extension Configuration window, Group tab, you can see the groups to which an
extension is assigned, and you can change those assignments. Hunt groups are created
in the Huntgroup Configuration window (see “Establishing Hunt Group Membership” on
page 172). Workgroups are created in the Workgroup Configuration window (see
“Establishing Workgroup Membership” on page 190). Group members are assigned in
those configuration windows, as well.
Once a group is established, use the Extension Configuration window, Group tab, to
configure hunt group and workgroup options for an individual agent extension, such as
how much wrap-up time to allow that individual agent after a workgroup call.