User guide
Table Of Contents
- About This Manual
- Overview
- Technology Enhancements in Release 5.1
- SIP Implementation
- Multi-Site Enterprise Management - AltiEnterprise Manager
- Multi-Chassis Gateway Support (ACM only)
- Capacity Improvements
- Voice Processing New Features and Enhancements
- PBX New Features and Enhancements
- Call Center New Features and Enhancements
- Client Application New Features and Enhancements
- IP Phone New Features and Enhancements (IP600, IP710, IP705)
- Key System Features
- Technology Enhancements in Release 5.1
- Software Installation & License Registration
- Getting Around AltiWare Administrator 5.1
- System Configuration
- Setting General Parameters
- Setting a System Number Plan
- Setting Business Hours
- Routing Calls on Holidays
- Configuring System Speed Dialing
- Defining System Call Restrictions
- Creating Account Codes
- Setting up Call Reports
- Country-Relevant Settings
- Audio Peripheral Configuration
- Activity
- Feature Profiles
- CT-Bus Configurations
- Voice Mail Configuration
- Auto Attendant Configuration
- Board Configuration
- Using the Triton Resource Board
- Using the Triton MeetMe Conference Board
- Configuring the Quantum Board
- Configuring the Triton Analog Station Board
- Configuring the Triton Analog Trunk LS/GS and LS Boards
- Configuring the Triton VoIP Board
- Configuring the Triton T1/E1 Board
- Configuring Virtual Boards SIPSP and H323SP
- Configuring the MAX Board
- Configuring the Virtual MobileExt Board
- Trunk Configuration
- Trunks Out of Service
- Channel Identification
- Opening the Trunk Configuration Window
- Selecting Trunks to Set Attributes
- Configuring One or Multiple Trunks
- Setting General Trunk Attributes
- H323 Tie Trunk Properties
- SIP Tie Trunk Properties
- SIP Trunk Properties
- Triton T1/E1 Trunk Properties
- Triton Analog Trunk GS/LS Properties
- Quantum Trunk Properties
- Incoming Call Routing
- Outgoing Call Blocking
- In Call Routing Configuration
- Out Call Routing Configuration
- Extension Configuration
- Setting Up IP Extensions
- AltiGen IP Phone Configuration
- Mobile Extension Configuration
- Hunt Group Configuration
- Paging Group Configuration
- Line Park Configuration
- Workgroup Configuration
- Managing and Using MeetMe Conference
- Network Configuration Guidelines for VoIP
- Enterprise VoIP Network Management
- Understanding VoIP Bandwidth Requirements
- Opening AltiEnterprise Manager
- Setting VoIP Codec Profiles
- Assigning Codec Profiles to IP Addresses
- Defining IP Networks
- Defining the IP Dialing Table
- The Multi-site VoIP Domain
- Working with Servers in the VoIP Domain
- Managing VoIP Domain Users
- Configuring Global Least Cost Routing
- When Information May Be Out of Sync
- System Report Management
- Tools and Applications
- E1-R2 and E1 ISDN PRI Installations
- Required Service Parameters
- Network Ports
- Technical Support & Product Repair Services
- Troubleshooting
- Index
Chapter 7: Extension Configuration
AltiWare ACC 5.1 Administration Manual 135
IP Extension Configuration
See “Setting Up IP Extensions” on page 157 for information on configuring this section
of the Extension Configuration General tab.
Message Waiting
Signal Type
Type of Message Waiting indicator for the phone set:
•None
• FSK/SDMF—Frequency Shift Keying/Single Data
Message Format indicator.
• FSK/MDMF—Frequency Shift Keying/Multiple
Data Message Format indicator. (Default for US/
Canada installation.)
Flash Duration Specifies the Flash Duration time in milliseconds:
• 85-750 (default)
• 50-600
• 100-700
• 150-800
• 200-900
• 300-1000
Ringing Frequency
(Hz)
Select the frequency in Hz that is necessary for the
equipment attached to this line: 28 (default) or 20.
Line Disconnect
Signal
The loop current break desired for answering
supervision. Range 600-1000 ms (1000 ms is
default).
Caller ID
Transmission
Methods
Specifies how Caller ID will be detected:
• CID between 1st and 2nd ring - Caller ID is
received between first and second ring. (Most
common in US/Canada)
• DT-AS+CID prior to ringing - Dual Tone Alerting
Signal Caller ID is received prior to ringing.
• RP-AS+CID prior to ringing - Ring Pulse Alerting
Signal Caller ID is received prior to ringing.
Receive from phone
(dB Gain)
Range -3 ~ +3 db
You can decrease or increase the extension phone's
talk volume with this setting. Default is 0 dB.
Transmit to phone
(dB Gain)
Range -3 ~ +3db
You can decrease or increase the extension phone's
receiving volume with this setting. The volume will
be lower or higher for the extension user. Default is
0 dB.
Parameter Description