User`s guide

6
Powering On the SoundBlade
1. If you haven’t previously paired your mobile phone and inMotion
wireless speaker system following the instructions in the Setting Up
the SoundBlade section, do so now.
2. Press and hold the button on the SoundBlade until you hear a
pair of low/high tones (approximately 1 second). The blue light will
ash intermittently, as the speaker system looks for the mobile
phone it was last paired with. If your mobile phone is turned on
and Bluetooth is enabled, you will hear a series of double beeps and
high-pitched tones. If not, you will hear a series of double beeps
followed by low tones. (NOTE: This does not occur if the AUX IN is
in use.)
. The SoundBlade is powered on at this point.
Powering Off the SoundBlade
1. Momentarily press the button to power down the SoundBlade. The
light will ash red  times and you’ll hear a pair of high/low tones.
2. The SoundBlade is now off.
Listening to Music
1. Make sure your mobile phone is on, Bluetooth is enabled, and the
phone is within 1 meter ( feet) of the SoundBlade. (Please refer to
your mobile phone user guide for specic instructions.)
2. Power on the SoundBlade following the instructions in the Powering
On the SoundBlade section.
. Your SoundBlade and mobile phone should be Bluetooth connected
now.
4. Play a music le on your mobile phone. You should hear the music
on the SoundBlade.
Remote Controlling Music with the SoundBlade
The Bluetooth connection between your mobile phone and the
SoundBlade provides wireless control.
1. Press the button to play or pause the music on the mobile phone.
2. Press the button once to stop the music on the mobile phone.
. Press the button once to restart a song. Press the button
repeatedly to move backward in the mobile phone’s playlist.
4. Press the button repeatedly to move forward in the mobile
phone’s playlist.
Muting/Unmuting the Microphone
1. Press and hold the button until you hear a low tone and then
a high tone (approximately  seconds).
2. Release the button. The microphone of SoundBlade will be
muted/unmuted.
Using the SoundBlade with Other Audio Sources
1. Connect other stereo audio sources to the SoundBlade using the
AUX IN jack on the back. Connect any other source that has a stereo
.5mm plug (headphone-style plug).
2. Power on the SoundBlade following the instructions in the Powering
On the SoundBlade section.
. Make sure your audio source features an AUDIO OUT jack. For
optimum audio performance set the volume level of your audio
source at approximately three quarter volume and use the
SoundBlade volume controls to adjust the overall volume level.
(Check your audio source’s user’s manual for specic instructions.)
4. Start your audio source. You should hear the sound on the
SoundBlade now. (NOTE: Using AUX IN disconnects any Bluetooth
devices.)
Adjusting the Volume
1. Press the + button to increase the volume to the desired level.
2. Press the – button to reduce the volume to the desired level.
Note that the output volume of your mobile phone has a direct effect
on the overall volume of the SoundBlade. Experiment with raising
and lowering the output volume of your mobile phone to see how it
changes the amplied sound of the SoundBlade.
Manually Connecting to the SoundBlade
If you power on the SoundBlade before your mobile phone or before
you enable Bluetooth, or if your Bluetooth connection is lost, you may
need to manually connect your phone to the SoundBlade. (Note that
if you lose the Bluetooth connection, you’ll hear a single high-pitched
beep.)
1. Make sure your mobile phone is on, Bluetooth is enabled, and the
phone is within 1 meter ( feet) of the SoundBlade. (Please refer to
your mobile phone user guide for specic instructions.)
2. Ensure the SoundBlade is powered on following the instructions in
the Powering On the SoundBlade section.
. Momentarily press the button on the SoundBlade.
4. Your mobile phone and the SoundBlade wireless speaker system
should now be connected.
Manually Disconnecting from the SoundBlade
1. Press and hold the button until 2 beeps are heard
(approx.  seconds).
2. Release the button to break your Bluetooth connection.