User`s guide
LOUDNESS
The loudness function contours
the
high and
low
frequencies
to
maximize the
perceived audio.
Press
the
"LOUDNESS"
button
on
the
control pod
or
"LOUD"
button
on
the
wireless remote
to
turn
it
on.
Press
either
button
again
to
turn
it
off.
SFX
TECHNOLOGY'M
Sound Field
Xpander™
technology allows your speaker system
to
deliver a
wider
stereo image
for
bigger sound
at
the
touch
of
a
button.
Press
the
"SFX"
button
on the control pod
or
wireless remote
to
turn
it on.
Press
it
again
to
turn
it
off.
Note: This feature does
not
work
when using headphones.
STAND-BY/MUTE
To
mute
the
speaker system,
press
the
6
button
located on
the
control pod
or
wireless remote. The
LED
on
the
control pod
will
turn
off.
To
un-mute, perform
either
command again.
Note: While in stand-by
or
mute mode,
the
system continues
to
receive power.
To
completely shut
down
the
unit
unplug
the
unit
from
the
wall.
SYSTEM
SPECI FICATIONS
RESET
The
button
marked
with
the
word
"reset" on
the
wireless remote restores
volume,
bass,
treble, loudness and
SFX
controls
to
original factory settings.
IPOD/MP3
PLAYER
JACK
The iPod
or
MP3
player jack
is
located on
the
side
of
the control pod.
Use
it
to
connect any audio source
that
has
a stereo 3.5mm plug (i.e. headphone style
plug.)
Caution: Make sure
the
audio source features a line-out jack. This
will
ensure
that
the
output
is
not
amplified. Check
the
owner's manual
for
your audio device
for
more information.
HEADPHONES
The headphone jack
is
located on
the
side
of
the
control pod.
Use
it
to
connect
any stereo headphones
with
a 3.5mm plug.
Note: When headphones are connected,
the
speaker system
is
muted.
Altec Lansing's superior sound comes
from
our
patented Dynamic
EQ
technology, which utilizes custom-built,
high-fidelity
drivers, state-of-the-art equalization circuitry,
and a harmonious mix
of
the
following
specifications:
Sound
Pressure
Level
(SPL):
Total Continuous Power:
• Front Speakers:
• Subwoofer:
92
dB
46
Watts
RMS
11
Watts/channel @ 4 ohms
@ 10%
THD
@ 180
Hz
-
20
kHz
2 Channels Loaded
24
Watts @ 8 ohms
@ 10%
THD
@
32
Hz
- 180
Hz
Single Channel Loaded
System
Response:
Signal
to
Noise Ratio
@ 1 kHz input:
Drivers (per satellite):
Subwoofer:
32
Hz
-
20
kHz (-10
dB)
>
85
dB
One 40mm mid-range driver and
one 18mm high-end
tweeter
Two 5.25"
long-throw
woofers
in isobaric configuration
*Power rating conforms
to
FTC
Amplifier
Rule
#16
C.ER.
Part 432.
TROLJBLLSIiOOIING
SYMPTOM POSSI
BLF
PROBl
EM
SOLUIION
No
LEDs
are lit. Power isn't
turned
on.
Turn on
the
speaker system by pressing
the
6
button
on
the
control pod
or
wireless remote.
An
LED
will
light
on
the
control pod when
the
power
is
ON.
AC
power cord isn't connected
to
the
wall outlet.
After
all
other
connections are made, plug
the
AC
power cord (on
the
back
of
subwoofer)
into
a wall outlet.
Surge
protector
(if
used) isn't powered on.
If
the
AC
power
cord
is
plugged
into
a surge protector, make sure
the
surge
protector
is
switched on.
Wall
outlet
not
functioning.
Plug another device
into
the wall
outlet
(same jack)
to
verify
the
wall
outlet
is
working.
3