USER’S MANUAL 30-Inch Propane Fire Pit Table THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Before You Start Please read all instructions carefully. Retain instructions for future reference. Seperate and count all parts and hardware. Read through each step carefully and follow the proper order. We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled. Always place the product on a flat, steady and stable surface.
Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death. WARNING • The installation of this unit must adhere to local codes or Propane Storage and Handling Code, CSA B149.2. • THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• Combustible material should not be within 60 inches of the top of the unit, or within 48 inches around the entire unit. • Keep the appliance area clear and free fr vapors and liquids. • • Do not add water into the unit. • Do not operate unit if any part has been under water. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and any gas control that has been under water. • Do not disconnect any part while unit is in use.
Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by the manufacturer . Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance. For assistance with repair or replacement of the burner or any other parts, please contact COSTWAY. NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling.
ITEM# DESCRIPTION PICTURE QTY A Table Leg 1PC B Table Leg 1PC C Table Leg 1PC Table Leg 1PC D E F G Panel 1PC Panel 1PC Panel H Door I Tank Holder/Base J Table Lid Fire Table with Burner K 6 1PC 1PC 1PC 1PC 1PC
ITEM# PICTURE DESCRIPTION PVC L QTY 1PC M lava rocks 1BOX N Screw(M6*12MM) 17 PCS O Screwdriver 1PC P M6 Washer 20 PCS Q Screw(M6*25MM) 7 4 PCS
Do not lock the screws until the assembly is complete. 1.Check the control knob for gas supply system is turned to OFF position before, starting your assembly. P B C A Q D 2.Connect the tank holder/base（I）With table Legs （A/B/C/D）by 4pcs screws (Q) and 4pcs M6 washers(P),do not fully tighten.
B A C F E P N G D 3.Connect panel (E,F,G)with table legs(A,B,C,D) by 12pcs screws(N) and 12pcs M6 washers(P). B F N C G D E H A 4.Hang the bottom (H) of the door plate on the round bracket.Top with 1PC screw(N)lock.
N P 5.Attach the assembled base to the bottom of top (K) using 4pcs of screws (N), and 4pcs M6 washers(P), make sure the panel (G) faces the valve stem，Lock all screws. 6.Put the table lid.
Place propane gas tank (not included) into the metal stand (I). Make sure the gas tank sits on the metal stand (I) completely. I Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the preassembled regulator from the table top (K) to the cylinder valve by turning the regulator coupling nut clockwise. Make sure it is fastened securely and tighten connections by hand only.
Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
• Before performing any maintenance always disconnect propane gas tank. • Store your product indoors during winter months. Avoiding extreme cold temperatures will prevent from exposure damage. • Keep the heating item free and clear from combustible materials. • Visually inspect burner for obstructions and keep tank enclosure free and clear from debris. • Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/ lava rocks/LavaGlass® are completely cooled down.
Problem Heating unit won’t light Burner won’t light while using a match Cause Solution Igniter pin and burner are wet Dry off with a soft cloth Igniter battery is incorrectly inserted Check which direction the battery is inserted Igniter pin is broken Contact COSTWAY for a replacement part Electrode wire is loose or disconnected Electrode wire is shorting between valve and igniter pin Reconnect wire to the igniter box located inside the fire pit behind the igniter box Contact COSTWAY.
