Owner's Manual
Table Of Contents
- Alpine Receiver
- Owner's Manual
- Contents
- Operating Instructions
- Getting Started
- Setup
- General Setup
- Connection (Bluetooth) Setup
- Camera Setup
- Sound Setup
- Apple CarPlay (Optional)
- Android Auto (Optional)
- Radio/HD Radio™/RBDS
- Radio Basic Operation
- Listening to the Radio
- Presetting Stations Manually
- Presetting Stations Automatically
- Tuning to Preset Station
- Receiving a Multicast (HD Radio™ Mode only)
- Forced Analog Mode
- Selecting the Receivable Program Type (RBDS FM Radio Mode only)
- Using Ballgame Mode (HD Radio™ Mode only)
- Displaying Radio Text (HD Radio™/RBDS FM Radio mode only)
- About the Feature Logos
- USB Flash drive (Optional)
- USB Audio
- USB Video
- USB Photo
- iPod mode on iPhone (Optional)
- SiriusXM Satellite Radio Operation (Optional)
- HDMI Device (Optional)
- Bluetooth Operation
- Hands-free Phone Control
- Bluetooth Audio
- Auxiliary Device (Optional)
- Camera Operation (Optional)
- iDataLink Operation
- Information
- Installation and Connections
- LIMITED WARRANTY
- Quick Reference Guide
- Warranty
- Owner's Manual
- Alpine Amplifier
26-EN
Time Correction Settings
[Time Correction] is selected on the Sound Setup Menu
screen.
Before performing the following procedures, see “About
Time Correction” (page 29).
Correction mode
Setting item:
Time Correction
1 Touch [Time Correction] on the Sound Setup
menu screen.
2 Touch the Correction mode button, and then
select [ms], [cm] or [inch].
3 Touch [ ] or [ ] for each speaker to adjust
the time or distance.
0.0 msec to 9.9 msec (0.1 msec/step)
0.0 cm (0.0 inch) to 336.6 cm (132.56 inch) (3.4 cm/step)
All speaker setting values are adjustable in the range of
20 ms or 680 cm.
4 To store the adjusted setting value, touch and
hold [Preset 1], [Preset 2], or [Preset 3] for at
least 2 seconds.
• Touch [ Flat] to set all values to 0.0.
• If the Rear Speaker setting is Off, the Rear Speaker setting
cannot be edited (page 28).
• If the Subwoofer setting is Off, the Subwoofer setting cannot be
edited (page 27).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset 1], [Preset 2], or [Preset 3] on the time
correction screen.
The setting stored in the Preset will be recalled.
Crossover Settings (X-Over)
[X-Over] is selected on the Sound Setup Menu screen.
Before performing the following procedures, see “About the
Crossover” (page 28).
Channel
Setting item:
X-Over
1 Touch [X-Over] on the Sound Setup menu
screen.
2 Touch [Channel], and then select [Front HPF],
[Rear HPF] or [SubW.LPF].
3 Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [ ] or [ ] of “Freq.” (Frequency), and then select the
cut-off frequency.
Setting contents:
20.0 / 25.0 / 31.5 / 40.0 / 50.0 / 63.0 / 80.0 (Initial setting)
/ 100.0 / 125.0 / 160.0 / 200.0 Hz
Adjusting the Slope
Touch [ ] or [ ] of “Slope”, and then adjust the HPF or LPF
slope.
Setting contents:
0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level
Touch [ ] or [ ] of “Level”, and then adjust the HPF or LPF
level.
Setting contents:
-12 to 0 dB (Initial setting: 0)
4 Repeat steps 2 to 3 to make adjustment to the
other channels.
5 To store the adjusted setting value, touch and
hold [Preset 1], [Preset 2], or [Preset 3] for at
least 2 seconds.
• Touch [ Flat] to initialize all values.
• If the Rear Speaker setting is Off, the Rear Speaker setting
cannot be edited (page 28).