Specifications

11-EN
01GB06iDAX001_R_QG.fm
ALPINE iDA-X001-EU_QG 68-08564Z75-A (EN)
FM TUNER SECTION
MW TUNER SECTION
LW TUNER SECTION
USB SECTION
GENERAL
CHASSIS SIZE
NOSEPIECE SIZE
DETACHABLE FRONT PANEL SIZE
• Due to continuous product improvement, specifications and design
are subject to change without notice.
• Be sure to disconnect the cable from the (–) battery post before
installing your iDA-X001. This will reduce any chance of damage to
the unit in case of a short-circuit.
• Be sure to connect the colour coded leads according to the diagram.
Incorrect connections may cause the unit to malfunction or damage
to the vehicle
’ s electrical system.
• When making connections to the vehicle’s electrical system, be
aware of the factory installed components (e.g. on-board computer).
Do not tap into these leads to provide power for this unit. When
connecting the iDA-X001 to the fuse box, make sure the fuse for the
intended circuit of the iDA-X001 has the appropriate amperage.
Failure to do so may result in damage to the unit and/or the vehicle.
When in doubt, consult your Alpine dealer.
• The iDA-X001 uses female RCA-type jacks for connection to other
units (e.g. amplifier) having RCA connectors. You may need an
adaptor to connect other units. If so, please contact your authorized
Alpine dealer for assistance.
• Be sure to connect the speaker (–) leads to the speaker (–) terminal.
Never connect left and right channel speaker cables to each other or
to the vehicle body.
Accessory List
• Digital Media receiver ....................................................... 1
• Power cable ....................................................................... 1
• Mounting sleeve................................................................ 1
• Carrying case .................................................................... 1
• Front frame ........................................................................1
• USB cable .......................................................................... 1
• iPod Dock interface cable................................................. 1
• Rubber Cap........................................................................ 1
• Hex Bolt.............................................................................. 1
• Screw (M5x8) .....................................................................4
• Quick Reference Guide...............................................1 set
Specifications
Tuning Range 87.5-108.0 MHz
Mono Usable Sensitivity 0.7 µV
Alternate Channel Selectivity 80 dB
Signal-to-Noise Ratio 65 dB
Stereo Separation 35 dB
Capture Ratio 2.0 dB
Tuning Range 531-1,602 kHz
Sensitivity (IEC Standard) 25.1 µV/28 dB
Tuning Range 153-281 kHz
Sensitivity (IEC Standard) 31.6 µV/30 dB
USB requirements USB 1.1/2.0
Max. Power Consumption 500mA
USB Class Mass Storage
File System FAT 12/16/32
MP3 Decoding MPEG-1/2 AUDIO Layer-3
WMA Decoding Windows Media™ Audio
AAC Decoding AAC-LC format “.m4a” file
Number of Channels 2-Channel (Stereo)
Frequency Response* 5-20,000 Hz (±1 dB)
Total Harmonic Distortion 0.008% (at 1 kHz)
Dynamic Range 95 dB (at 1 kHz)
Signal-to-Noise Ratio 105 dB
Channel Separation 85 dB (at 1 kHz)
* Frequency response may differ depending on the encoder
software/bit rate.
Power Requirement 14.4 V DC
(11-16 V allowable)
Maximum Power Output 50 W × 4
Maximum Pre-Output Voltage 2 V/10 k ohms
Weight 1.0 kg (2 lbs. 3 oz)
Width 178 mm (7")
Height 50 mm (2")
Depth 156 mm (6-1/8")
Width 170 mm (6-3/4")
Height 46 mm (1-13/16")
Depth 24 mm (15/16")
Width 107 mm (4-1/4")
Height 46 mm (1-13/16")
Depth 30 mm (1-3/16")
Installation
Caution
Do not block the unit’s heat sink, thus preventing air circulation.
If blocked, heat will accumulate inside the unit and may cause a
fire.
Heat sink
01GB00iDAX001_R_QG.book Page 11 Friday, December 22, 2006 11:23 AM