Owner's Manual
Table Of Contents
- Quick Reference Guide
- Owners Manual (Supplied on CD-ROM)
- Reset
- Demo Mode
- Table of Contents
- Attaching / Removing Faceplate (CDE-164BT Only)
- Supplied Accessories
- Parts & Controls
- Operating Instructions
- Getting Started
- Radio
- RBDS
- CD/MP3/WMA
- Sound Setting
- Adjusting Subwoofer Level/Bass Level/Treble Level/Balance/Fader/Defeat
- Sound Setting
- Equalizer Presets
- Setting BASS ENGINE SQ ON/OFF
- Displaying the BASS ENGINE SQ PARAMETER
- Adjusting the Parametric Equalizer Curve (9BAND P-EQ)
- Setting the Source Volume Level
- Adjusting the Crossover Settings
- Turning Subwoofer ON/OFF
- Setting the Subwoofer Phase
- Setting the Subwoofer System
- Setting the Time Correction Unit (LENGTH)
- Adjusting the Time Correction (TCR)
- External Device
- Setting the Media Xpander mode
- BASS ENGINE SQ Function
- About Time Correction
- About the Crossover
- Other Functions
- SETUP Menu
- BT Hands Free Calling
- Setup Before Using
- Bluetooth SETUP
- Setting the Bluetooth Connection (BT IN)
- Setting the Auto Pairing with iPod/iPhone
- Setting the Bluetooth Device
- Setting the Visible Mode
- Setting the Bluetooth sound quality
- Setting the caller information display ON/OFF
- Setting the Phone Book Update
- Changing the Phone book List Order
- Selecting the output speaker
- Displaying the firmware version
- Updating the firmware
- Hands-Free Phone Control
- About the Hands-Free Phone
- Answering a Call
- Hanging up the Telephone
- Calling
- Voice Control Operation
- Call waiting function
- Preset a number in the Phone Menu (Shortcut dial)
- Dialing the preset number
- Adjusting the volume when receiving a Call
- Muting the microphone input quickly (Voice Mute)
- Call Switching Operation
- Bluetooth Audio Operation
- Flash Memory
- iPod/iPhone
- Pandora internet radio
- SiriusXM Satellite Radio Operation (Tuner Required)
- Receiving Channels with the SiriusXM Tuner
- SiriusXM Setting
- Checking the SiriusXM Radio ID Number
- Storing Channel Presets
- Tuning Channels using Presets
- SmartFavorites Functions
- Storing the desired Artist and Song Alerts
- Receiving and Tuning to an Alert
- Search Function
- Using Jump Memory and Jump Recall function
- Replay Function
- Parental Lock Function
- iTunes radio tagging
- Changing the Display
- Information
- Installation and Connections
- Troubleshooting
- Messages
- Specs
- Scan of CD-ROM
- Warranty
56-EN
Installation
CAUTION
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
The main unit must be mounted within 35 degrees of the
horizontal plane, back to front.
CDE-W265BT
CDE-164BT
1
Remove the mounting sleeve from the main unit (refer to
“Removal” on page 57).
CDE-W265BT
CDE-164BT
* If the installed mounting sleeve is loose in the dashboard, the
pressure plates may be bent slightly to remedy the problem.
2
Reinforce the head unit with the metal mounting strap
(not supplied). Secure the ground lead of the unit to a
clean metal spot.
Connect each input lead coming from an amplifier to the
corresponding output lead coming from the left rear of the
CDE-W265BT/CDE-164BT. Connect all other leads of the
CDE-W265BT/CDE-164BT according to details described in the
CONNECTIONS section.
CDE-W265BT
CDE-164BT
Note
• For the screw marked “
*
”, use an appropriate screw for the chosen
mounting location.
3
Slide the CDE-W265BT/CDE-164BT into the dashboard
until it clicks. This ensures that the unit is properly locked
and will not accidentally come out from the dashboard.
Install the detachable front panel.
To prevent external noise from entering the audio system.
• Locate the unit and route the leads at least 10 cm away from the
car harness.
• Keep the battery power leads as far away from other leads as
possible.
• Connect the ground lead securely to a bare metal spot (remove
any paint, dirt or grease if necessary) of the car chassis.
• If you add an optional noise suppressor, connect it as far away
from the unit as possible. Your Alpine dealer carries various
noise suppressors, contact them for further information.
• Your Alpine dealer knows best about noise prevention
measures so consult your dealer for further information.
Less than 35°
Less than 35°
Dashboard
Mounting Sleeve (Included)
Pressure Plates*
This unit
Dashboard
Mounting Sleeve (Included)
Pressure Plates*
This unit
*
Bolt Stud
Hex Nut (M5)
Metal
Mounting
Strap
Screw
This unit
*
Bolt Stud
Hex Nut (M5)
Metal
Mounting
Strap
Screw
This unit