Bluetooth® Software Update User s Guide XA-W407BT Type B: CDE-125BT/-126BT, CDE-113BT/-114BT, CDE-103BT/-104BTi, INA-W910R, KCE-250BT Type D: KCE-400BT, iXA-W407BT
Introduction This guidebook describes procedures for updating Bluetooth software. This is necessary in order to update the compatibility with new phones. Be sure to read the warning and procedures carefully before updating. Requirements • The update software varies by model. Confirm the software before updating. • Updating requires a computer with built-in Bluetooth or a Bluetooth dongle. • Do not update Bluetooth software while driving.
Bluetooth Software Update Tool Installation 2 1 Open the setup.exe file and follow the instructions on the screen. Then press the Next > button. Press the Next > button when the following window appears. 4 3 Select the folder where you want to install the Bluetooth Software Update Tool , and press the Next > button. Select the Start Menu folder in which you want to create a shortcut for the update tool and press the Install button, or simply press the Install button if the preset directory is ok.
Bluetooth Software Update 1 Prepare for Bluetooth software update. • Park the vehicle in a safe place. • Turn off the engine. 2 Set the key position to ACC and turn on the Head Unit. 3 Set Bluetooth communication with the PC. But do not start Bluetooth Software Update Tool here. For Type B: CDE-125BT/-126BT, CDE-113BT/-114BT, CDE-103BT/-104BTi, INA-W910R, KCE-250BT For Type D: KCE-400BT, iXA-W407BT Move to the next step. 1. Set pairing between Alpine device and computer.
Activate FW UPDATE in the Head Unit Bluetooth setup menu in order to start the software update. The procedure is described in the Head Unit manual. 6 From this point, computer operation is required. Go to the Start Menu and select Bluetooth Software Update Tool . The window on the right will appear when the tool is launched. Press the Next > button. On the screen, a window containing all the available Bluetooth software types will appear. 7 Select the correct type and press the Next > button.
9 If everything is ok, the window on the left will be displayed. If there is no Bluetooth dongle inserted in the computer, or if Bluetooth is not activated on the computer, or if there is a problem with the Bluetooth device drivers, the window on the right will appear. If the problem continues to exist after you press the button Test Bluetooth , the popup on the left will appear. If the problem is solved, when you press the button Test Bluetooth , the popup on the right will be displayed.
11 When the search is finished, the available devices are displayed in a window as shown on the right. Select your Alpine Bluetooth device and press the Next > button. 12 Set Bluetooth communication with the PC. But do not start Bluetooth Software Update Tool here. For Type D: KCE-400BT, iXA-W407BT For Type B: CDE-125BT/-126BT, CDE-113BT/-114BT, CDE-103BT/-104BTi, INA-W910R, KCE-250BT Before starting the update, the Bluetooth Software Update Tool will ask for pairing for the Alpine Bluetooth device.
14 When flashing stops, this window appears. Press the Finish button. Also, after FIRMWARE UPDATE END PLEASE PUSH ANY BUTTON message appeared on Head Unit display, press any button on Head Unit to exit from the software update mode. 15 Turn the ACC off for software update finalization on KCE-400BT, iXA-W407BT and press RESET switch of CDE-125BT/-126BT, CDE-113BT/-114BT, CDE-103BT/-104BTi, INA-W910R, KCE-250BT (this procedure is described in the Head Unit manual).
Error Messages Update situation Error message Action Bluetooth connection The communication with the device could not be established. Cannot communicate between PC and Alpine Bluetooth device, or Alpine Bluetooth device is not working. • Confirm Bluetooth device on PC, or try turning off and on ACC for the Alpine Bluetooth device. Device authentication The specified file in invalid or corrupted. Please get the correct version and check the website, and try again.
