Owner`s manual
CD
Antenna Receptacle
® Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only
for
coli/roiling the vehicle's power
antenna. Do not lise this lead
to
turn on
lilt
amplifier
or
a signal
processor, etc.
@ Remote Turn-On Lead (BluelWhite)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
@ Audio Interrupt
In
Lead (Pink/Black)
Connect this lead to the Audio interface output of a cellular
phone which provides ground shorting when a call
is
received.
@ Illumination Lead (Orange)
This lead may be connected to the vehicle's instrument
cluster illumination lead. This will allow the backlighting of
this unit to dim whenever the vehicle's lights are turned on.
@ Switched Power Lead (Ignition) (Red)
Connect this lead to
an
open terminal on the vehicle's fuse
box or another unused power source which provides (+)
12V
only when the ignition
is
turned on or
in
the accessory
position.
CJ)
Battery Lead (Yellow)
Connect this lead
to
the positive (+) post of the vehicle's
battery.
@ Ground Lead (Black)
Connect this lead
to
a good chassis ground on the vehicle.
Make sure the connection is made
to
bare metal and
is
securely fastened using the sheet metal screw provided.
® Power Supply Connector
@)
Right Front (+) Speaker Output Lead (Gray)
@ Right Front
(-)
Speaker Output Lead (GraylBlack)
@ Right Rear
(-)
Speaker Output Lead (VioletIBlack)
@ Right Rear (+) Speaker Output Lead (Violet)
@ Left Rear (+) Speaker Output Lead (Green)
@ Left Rear
(-)
Speaker Output Lead (Green/Black)
@ Left Front
(-)
Speaker Output Lead (White/Black)
@ Left Front (+) Speaker Output Lead (White)
@ Fuse Holder (10A)
@ Front Output RCA Connectors
RED
is right and WHITE is left.
® Rear/Subwoofer Output RCA Connectors
® RCA Extension Cable (sold separately)
RED
is right and WHITE is left.
@ Full Speed connector
Control iPhone/iPod signals.
Connect this to
an
iPhone/iPod (or to an optional Bluetooth
INTERFACE (KCE-400BT))
To
use a hands-free mobile
phone, an optional Bluetooth INTERFACE (KCE-400BT)
connection is required. For details
on
connection, refer to
the Owner's Manual of the Bluetooth INTERFACE
(KCE-400BT).
You
can also connect this
to
an external
device (such as a portable player) by using conversion
cable (KCE-237B) for building up the AUX
IN
(sold
separately).
* Reler to "Setting the AUX+ SETUP Mode" (page /7).
AUX+
ON:
When
the
external device
is
connected.
AUX+
OFF:
When
an
iPhone/iPod
is
connected.
@ FULL
SPEEO™
Connection Cable (KCE-433iV) (sold
separately)
@ KCE-400BT Connection Cable (Included with
KCE-400BT)
@ Front AUX Input Terminal
This terminal allows for input of audio from an external
device (such as a portable player), using a commercially-
available converter cable.
@ USB Connection Terminal
Connect USB memory (sold separately)
To
prevent external noise from entering the audio system.
• Locate
the
unit
and
route
the
leads
at
least
10
cm away from
the
car
harness.
• Keep
the
battery power leads
as
far away from other
leads
as
possible.
• Connect
the
ground lead securely
to
a
bare
metal
spot
(remove
any
paint, dirt or
grease
if
necessary)
of
the
car
chassis.
•
If
you
add
an
optional noise
suppressor,
connect
it
as
far away from
the
unit
as
possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
• Your Alpine dealer knows
best
about noise prevention
measures
so
consult your dealer for further information.
28-EN