Owner`s manual
Installation
and
Connections
Before
installing
or
connecting
the unit, please read the
following
and pages 3
to
5
of
this
manual
thoroughly
for
proper use.
~Warning
MAKE
THE
CORRECT
CONNECTIONS.
Failure to make the
proper
connections
may result in fire
or
product
damage.
USE
ONLY
IN
CARS
WITH
A
12
VOLT
NEGATIVE
GROUND.
(Check with
your
dealer
if
you are not sure.) Failure to
do
so may
result in fire, etc.
BEFORE
WIRING,
DISCONNECT
THE
CABLE
FROM
THE
NEGATIVE
BATIERY
TERMINAL.
Failure to
do
so
may result in electric shock
or
injury due to
electrical shorts.
DO
NOT
ALLOW
CABLES
TO
BECOME
ENTANGLED
IN
SURROUNDING
OBJECTS.
Arrange wiring and
cables
in
compliance
with the manual to
prevent obstructions
when
driving.
Cables
or
wiring that
obstruct
or
hang up on
places
such as the steering wheel,
gear
lever, brake
pedals, etc.
can
be extremely hazardous.
DO
NOT
SPLICE
INTO
ELECTRICAL
CABLES.
Never cut away
cable
insulation
to
supply
power
to
other
equipment. Doing
so
will
exceed
the current
carrying
capacity
of
the wire
and
result in fire
or
electric shock.
DO
NOT
DAMAGE
PIPE
OR
WIRING
WHEN
DRILLING
HOLES.
When
drilling
holes
in the chassis for installation, take precautions
so
as not
to
contact,
damage
or
obstruct
pipes, fuel lines, tanks
or
electrical wiring. Failure to take such precautions may result in fire.
DO
NOT
USE
BOLTS
OR
NUTS
IN
THE
BRAKE
OR
STEERING
SYSTEMS
TO
MAKE
GROUND
CONNECTIONS.
Bolts
or
nuts llsed for the brake
or
steering
systems
(or
any
other
safety-related system),
or
tanks should
NEVER
be
used for
installations
or
ground
connections. Using such parts
could
disable
control
of
the vehicle
and
cause fire etc.
KEEP
SMALL
OBJECTS
SUCH
AS
BATIERIES
OUT
OF
THE
REACH
OF
CHILDREN.
Swallowing them may result
in
serious injury.
If
swallowed,
consult
a physician immediately.
DO
NOT
INSTALL
IN
LOCATIONS
WHICH
MIGHT
HINDER
VEHICLE
OPERATION,
SUCH
AS
THE
STEERING
WHEEL
OR
GEARSHIFT.
Doing so may obstruct forward vision
or
hamper
movement
etc.
and
results in serious accident.
IMPORTANT
Please record the serial number of your unit
in
the space provided
below and keep
it
as a permanent record. The serial number or the
engraved serial number
is
located on the boltom
of
the unit.
LhCaution
HAVE
THE
WIRING
AND
INSTALLATION
DONE
BY
EXPERTS.
The
wiring and installation
of
this unit requires special technical
skill and experience. To ensure safety, always contact the
dealer
where
you purchased this product to have the work done.
USE
SPECIFIED
ACCESSORY
PARTS
AND
INSTALL
THEM
SECURELY.
Be
sure to use only the specified accessory parts. Use
of
other
than
designated parts may
damage
this unit internally or may not
securely install the unit
in
place.
This
may
cause
parts to
become
loose resulting in hazards
or
product
failure.
ARRANGE
THE
WIRING
SO
IT
IS
NOT
CRIMPED
OR
PINCHED
BY
A
SHARP
METAL
EDGE.
Route the cables and wiring away from moving parts (like the seat
rails)
or
sharp
or
pointed edges. This will prevent
crimping
and
damage
to
the wiring.
If
wiring passes through a hole in metal, use
a rubber
grommet
to
prevent the
wire's
insulation from being cut by
the metal
edge
of
the hole.
DO
NOT
INSTALL
IN
LOCATIONS
WITH
HIGH
MOISTURE
OR
DUST.
Avoid installing the unit in locations with high incidence
of
moisture
or
dust. Moisture
or
dust
that penetrates into this unit may
result in product failure.
Precautions
• Be sure to disconnect the
cable
from the
(-)
battery post
before
installing
your
CDE-102.
This
will reduce any
chance
of
damage
to
the unit in case
of
a short-circuit.
• Be sure to
connect
the
color
coded leads according to the
diagram. Incorrect connections may
cause
the unit to
malfunction
or
damage
to the vehicle's electrical system.
•
When
making connections to the vehicle's electrical system,
be
aware
of
the factory installed
components
(e.g. on-board
computer).
Do
not tap into these leads to provide power for this
unit.
When
connecting the
CDE-I
02
to
the fuse box, make sure
the fuse for the intended circuit
of
the
CDE-l
02
has the
appropriate amperage. Failure to
do
so
may result in
damage
to
the unit
and/or
the vehicle.
When
in doubt,
consult
your
Alpine
dealer.
•
The
CDE-102
uses female
RCA-type
jacks
for connection to
other
units (e.g. amplifier) having RCA connectors.
You
may
need an
adaptor
to connect
other
units.
If
so, please contact
your
authorized Alpine dealer for assistance.
• Be sure to
connect
the speaker
(-)
leads to the
speaker
(-)
terminal. Never connect left and right channel speaker cables to
each
other
or
to
the vehicle body.
SERIAL NUMBER: _
INSTALLATION
DATE:
_
INSTALLATION TECHNICIAN: _
PLACE OF PURCHASE: _
25-EN