Owner`s manual

USB Memory Connection (Optional)
Connect USB memory
1 Open the cover of the USB connection terminal.
2 Connect the USB memory directly to the USB
connection terminal, or via the USB cable.
iPhone/iPod
(Optional)
SOURCEI<!>
o-'/ESC
Rotary encoder
1
....
~2':::)45ca6
I
I
0
c::J
B6:{(I)):JlI
liB
I\:.I~ ...Ii
,t:"\@
t\ \,~ -.1""'..... •
.. ..
~ ~IIJENT
I
~
Preset buttons
VIEW
(1 through 6)
~/MUTE
An iPhone/iPod can be connected to this unit by using the proprietary
ALPINE FULL SPEED'M Connection Cable (KCE-433iV) (sold
separately). When this unit is connected
by using the cable. the controls
on the iPod are not functional.
Remove USB memory
1 Carefully, pull out the USB memory from the USB
cable or the USB connection terminal.
2 Close the cover of the USB connection terminal.
This unit USB Connection Terminal
I
USB memory
rrr~~~~~~~~~~~:;;n(Sold separately)
OOO'~ [J I~·····~
?~~~))~r-I ------,.,~,~(§l !~ ..... I
s=nn'~""'.~
USB memory Cable (Sold
(Sold separately) Separately)
• Change to a source other than the USB memory mode, then remove
the USB memory,
If the USB memory is removed in the USB memory
mode, data may be damaged,
• When removing USB memory, pull it out straight.
•
If sound is not output or USB memory is not recognized even when
USB memory is connected, remove USB memory once, then connect
it again.
• Route the USB cable away from other cables, etc.
• Ajier removing the USB memory, close the cover
of the USB
connection terminal to prevent dust
or foreign objectsfrom entering
and causing a ma!tilllction.
About MP3/WMA/AAC File of USB
Memory
• Set AUX+ SETUP to OFF when an iPhoneliPod is connected (refer
to "Setting the AUX+ SETUP Mode" on page
17).
• ({the Bluetooth INTERFACE (KCE-400BT) and an iPhoneliPod are
connected
at the same time, be sure to disconnect the iPhoneliPod
from the Bluetooth INTERFACE (KCE-400BT) while turning
ACC to
OFF,
If you connect an iPhone to this unit, it can be used as an iPod. If you
use iPhone as a
handsjree phone, you need the optional Bluetooth
INTERFACE (KCE-400BT).
• Internet
and telephone functions of iPod touch or iPhone, etc., can
also be used when connecting to the unit. However. using these
functions will stop
or pause the playing songs, at this time do not
operate the unit to avoid a malfunction.
• Do not leave an iPhoneliPod in a
car. as its mechanism is sensitive to
high temperature and humidity conditions,
and damage may result.
iPhoneliPod models usable with this unit
Playing back MP3IWMAlAAC
MP3/WMA/AAC files are prepared, then stored to a USB
memory. This unit can recognize at least 100 folders (including
root folder) and 100 files per folder stored in USB memory,
Playback may not be performed
if a USB memory exceeds the
limitations described above,
Do not make a file's playback time more than 1 hour.
Media supported
This device can play back USB memory media.
Corresponding File Systems
This device supports FAT 12/16/32 for USB memory device.
• The unit
can be used with the following iPhone/iPod models.
iPhone
3G (version 2.0)
iPhone (version 1.1.4)
iPod touch (version 1.0.4)
iPod classic (version 1.1.1)
iPod nano (3rd generation) (version 1.1)
iPod nano (2nd generation) (version 1.1.3)
iPod with video (version 1.2.3)
iPod nano
(1 st generation) (version 1.3.1)
• For clarity in identifying your model
of iPod, please see
Apple's own
document "Identifying iPod models" at
http://support.apple.com/kb/HT1353
• This unit
does not support video playback from iPhone/iPod,
even using a video-compatible cable.
• If the unit is used with versions of iTunes earlier than 7.6,
correct function
and performance are not guaranteed.
i8-EN