MP3/WMA/AAC CD Receiver Owner's Manual

Level adjusting
(0 to -12 dB) Output frequency range
-j
I
.;- I~ Slope FLAT
i\~ - ~~~;e- ~~jUstlng
I
I
I
20 Hz : (Different from actual display)
HPF cut-off LPF cut-off
frequency frequency
• HPF (high passfilter): Cuts the lowerfrequencies and allows the
higherfrequencies to pass.
•
LPF (low passfilter): Cuts the higherfrequencies and allows the
lowerfrequencies to pass.
• Slope: The level change (in dB)
for a frequency change of one octave.
• The higher the slope value, the steeper the slope becomes.
• Adjust the slope to FLAT to bypass the HP
or LP filters.
• Do not use a tweeter without the
HPF on or set to a low frequency, as
it may cause damage to the speaker due to the low frequency content.
•
You cannot adjust the crossoverfrequency higher than the HPF or
lower than the LP F.
• Adjustment should be made according to the recommended crossover
frequency
of the connected speakers. Determine the recommended
crossoverfrequency
of the speakers. Adjusting to a frequency range
outside that recommended may cause damage to the speakers.
For the recommended crossoverfrequencies
of Alpine speakers, refer
to the respective Owner's Manual.
We are not responsible for damage or malfunction of speakers caused
by using the crossover outside the recommended value.
Adjusting and Storing the Crossover
Settings
Before performing the following procedures, refer to "About the
Crossover" (page 15).
1 Press A.SEL to recall the DSP adjust mode.
Media Xpander H Crossover H T.Correction H
Parametric EO/Graphic EO H Media Xpander
2 Turn the Rotary encoder to select the Crossover
mode, and then press .-/11 lENT.
3 Press BAND to select the band to be adjusted.
2.2ch (3WAY) System
I L=R
Setting Items:
LOW / MID-L / MID-H / HIGH
2.2ch (3WAY) System I UR
Setting Items:
LOW-L / LOW-R / MID-L-L / MID-L-R / MID-H-L /
MID-H-R / HIGH-L / HIGH-R
4 Press.... or ~ to select the desired cut-off frequency
(Crossover Point).
2.2ch (3WAY) System
Setting Items:
LOW / MID-L 20 Hz-200 Hz
MID-H 20
Hz-20 kHz
HIGH
(1 kHz-20 kHz)*1/(20 Hz-20 kHz)*2
16-EN
*1 When Maker's is selected, refer to "Setting the Response Slope for
the High Range Speaker (TW Setup)" (page 24).
*2 When User's is selected, refer to"Setting the Response Slope for the
High Range Speaker
(TW Setup)" (page 24).
5 Press SOURCEI<!> to adjust the slope.
Adjustable slope: FLAT*, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
* FLAT can be setfor the HIGH slope only when User's is selected in
"Setting the Response Slope
for the High Range Speaker
(TW Setup)" (page 24). Depending on the response characteristics of
the speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope
for the high range speaker is set
to FLAT.
6 Turn the Rotary encoder to adjust the output level.
Adjustable output level: -12 to 0 dB.
7 Repeat steps 3 to 6 to make adjustment to the other
bands.
8 When the setting is complete, store into anyone of
the
preset buttons (1 through 6) by pressing and
holding the desired button for at least 2 seconds.
9 Turn the Rotary encoder to select PROTECT
YES/NO, and then press
.-/11 lENT to store the
adjusted contents. .
PROTECT YES H PROTECT NO
(Initial setting)
• If YES is selected, the adjusted contents are protected and stored into
the preset buttons. When you want to store the parameter into a
protected preset button, "REPLACE NOIYES" can be selected.
• If NO is selected, the preset is stored.
10 After setting, press and hold ~/ESC for at least 2
seconds to return to normal mode.
• Pressing ~ IRTN during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds, the unit will return to the
normal mode.
3 Press BAND to select the band to be adjusted.
4.2ch (F/RISub-W) System
I L=R
setting items:
LOW (SUB-W) / MID (REAR) / HIGH (FRONT)
4.2ch (F/RISub-W) System I UR
setting items:
LOW (SUB-W)-L / LOW (SUB-W)-R / MID (REAR)-L /
MID (REAR)-R / HIGH (FRONT)-L / HIGH (FRONT)-R
4 Press.... or ~ .to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
4.2ch (F/RISub-W) System
Setting items:
20 Hz-200 Hz
5 Press SOURCEI<!> to adjust the slope.
Adjustable slope: FLAT, 6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.