Electronics Car Stereo System User's Manual
Table Of Contents
- Operating Instructions
- WARNING
- Getting Started
- Radio
- RDS
- Setting RDS Reception Mode and Receiving RDS Stations
- Recalling Preset RDS Stations
- Receiving RDS Regional (Local) Stations
- PI SEEK Setting
- Setting PTY31 (Emergency Broadcast) reception
- Setting the Time to automatically Adjust
- Receiving Traffic Information
- PTY (Programme Type) Tuning
- Receiving Traffic Information While Playing CD or Radio
- Priority News
- Displaying Radio Text
- CD/MP3/WMA/AAC
- Sound Setting
- Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Auto Volume/Defeat
- Setting the Subwoofer Level
- Setting the Bass Control
- Setting the Treble Control
- Adjusting the High Pass Filter
- Blackout Mode On and Off
- Turning Loudness On/Off
- Turning Subwoofer ON/OFF
- Setting the Subwoofer System
- Other Functions
- SETUP
- Bluetooth Setting
- General Setting
- Birthday Opening Message Setting (Birthday Set)
- Setting the Clock Display (Clock Mode)
- Setting of Calendar Display Pattern Switching (Calendar)
- Playing MP3/WMA/AAC Data (Play Mode)
- Sound (Beep) Guide Function
- Turning Mute Mode On/Off (INT Mute)
- Setting the AUX+ Setup Mode
- Setting the AUX+ Level (AUX IN GAIN)
- Setting the External Digital Input
- Setting the AUX Mode (V-Link)
- Connecting to an External Amplifier
- Setting the Language Font
- Demonstration
- Setting Adaptive Steering Remote Control
- Display Setting
- USB memory (Optional)
- iPod® (Optional)
- IMPRINT Operation (Optional)
- Changing MultEQ mode
- Adjusting Subwoofer Level/Bass Level/Treble Level/Fader (Between Front and Rear)/Balance (Between Left and Right)/Black Out in MultEQ mode
- Adjusting Sound Setting in Manual Mode
- Turning Subwoofer ON/OFF
- Setting the Subwoofer System
- Setting the Subwoofer Phase
- Setting the Subwoofer Channel (SUBW. Channel)
- Equalizer Presets (Factory’s EQ)
- Setting the Response Slope for the High Range Speaker (TW Setup)
- Setting the Filter type
- Turning Media Xpander ON/OFF
- Setting the MX Level
- Setting EQ mode
- Setting the Time Correction Unit (TCR Parameter)
- Blackout Mode On and Off
- Sound Field Adjustment
- About Time Correction
- About the Crossover
- About IMPRINT
- Changer (Optional)
- Remote Control
- Information
- Installation and Connections
6-EN
Accessory List
• Head unit ............................................................................1
• Power cable ........................................................................1
• Mounting sleeve.................................................................1
• Carrying case.....................................................................1
• Rubber Cap ........................................................................1
• Hex Bolt ..............................................................................1
• Screw (M5 × 8)....................................................................4
• Remote Control..................................................................1
• Battery (AAA size) .............................................................2
• Owner’s Manual .......................................................... 1 set
Turning Power On and Off
Press SOURCE/ to turn on the unit.
• The unit can be turned on by pressing any other button except
(OPEN).
Press and hold SOURCE/ for at least 2 seconds to turn
off the unit.
• The first time power is turned on, the volume will start from level 12.
Detaching and Attaching the Front Panel
Detaching
1
Turn off the unit power.
2
Press (OPEN) to open the front panel.
To close the front panel, press the left side until it locks as
shown in the figure below.
3
Grasp the front panel firmly, slide to the left ,
and then pull to remove.
• The front panel may become hot in normal usage (especially the
connector terminals on the back of the front panel). This is not a
malfunction.
• To protect the front panel, place it in the supplied carrying case.
• When detaching the front panel, do not apply excessive force as it
may result in malfunction.
• Do not leave the front panel open, or drive the car with the panel
open as it may result in an accident or malfunction.
Attaching
1
Insert the right side of the front panel into the main
unit. Align the groove on the front panel with the
projections on the main unit.
2
Push the left side of the front panel until it locks
firmly into the main unit.
• Before attaching the front panel, make sure that there is no dirt or
dust on the connector terminals and no foreign object between the
front panel and the main unit.
• Attach the front panel carefully, holding the sides of the front panel to
avoid pushing buttons by mistake.
Initial System Start-Up
Be sure to press the RESET switch when using the unit for the first
time, after changing the car battery, etc.
1
Turn off the unit power.
2
Press (OPEN) to open the front panel, and then
remove it.
Getting Started
Rotary encoder
(OPEN)
F/SETUP
SOURCE/
MUTE
/ENT
/ESC