Electronics Car Stereo System User's Manual
Table Of Contents
- Operating Instructions
- WARNING
- Getting Started
- Radio
- RDS
- Setting RDS Reception Mode and Receiving RDS Stations
- Recalling Preset RDS Stations
- Receiving RDS Regional (Local) Stations
- PI SEEK Setting
- Setting PTY31 (Emergency Broadcast) reception
- Setting the Time to automatically Adjust
- Receiving Traffic Information
- PTY (Programme Type) Tuning
- Receiving Traffic Information While Playing CD or Radio
- Priority News
- Displaying Radio Text
- CD/MP3/WMA/AAC
- Sound Setting
- Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader (Between Front and Rear)/Auto Volume/Defeat
- Setting the Subwoofer Level
- Setting the Bass Control
- Setting the Treble Control
- Adjusting the High Pass Filter
- Blackout Mode On and Off
- Turning Loudness On/Off
- Turning Subwoofer ON/OFF
- Setting the Subwoofer System
- Other Functions
- SETUP
- Bluetooth Setting
- General Setting
- Birthday Opening Message Setting (Birthday Set)
- Setting the Clock Display (Clock Mode)
- Setting of Calendar Display Pattern Switching (Calendar)
- Playing MP3/WMA/AAC Data (Play Mode)
- Sound (Beep) Guide Function
- Turning Mute Mode On/Off (INT Mute)
- Setting the AUX+ Setup Mode
- Setting the AUX+ Level (AUX IN GAIN)
- Setting the External Digital Input
- Setting the AUX Mode (V-Link)
- Connecting to an External Amplifier
- Setting the Language Font
- Demonstration
- Setting Adaptive Steering Remote Control
- Display Setting
- USB memory (Optional)
- iPod® (Optional)
- IMPRINT Operation (Optional)
- Changing MultEQ mode
- Adjusting Subwoofer Level/Bass Level/Treble Level/Fader (Between Front and Rear)/Balance (Between Left and Right)/Black Out in MultEQ mode
- Adjusting Sound Setting in Manual Mode
- Turning Subwoofer ON/OFF
- Setting the Subwoofer System
- Setting the Subwoofer Phase
- Setting the Subwoofer Channel (SUBW. Channel)
- Equalizer Presets (Factory’s EQ)
- Setting the Response Slope for the High Range Speaker (TW Setup)
- Setting the Filter type
- Turning Media Xpander ON/OFF
- Setting the MX Level
- Setting EQ mode
- Setting the Time Correction Unit (TCR Parameter)
- Blackout Mode On and Off
- Sound Field Adjustment
- About Time Correction
- About the Crossover
- About IMPRINT
- Changer (Optional)
- Remote Control
- Information
- Installation and Connections
44-EN
Installation
• The main unit must be mounted within 35 degrees of the horizontal
plane, back to front.
Removal
1. Remove the detachable front panel.
2. Use a small screwdriver (or similar tool) to push the
locking pins to the “up” position (see above drawing).
As each pin is unlocked, gently pull out on the unit to
make sure it does not re-lock before unlocking the
second pin.
3. Pull the unit out, keeping it unlocked as you do so.
Caution
Do not block the unit’s fan or heat sink, thus preventing air
circulation. If blocked, heat will accumulate inside the unit and
may cause a fire.
Caution
When you install this unit in your car, do not remove the
detachable front panel.
If the detachable front panel is removed during installation, you
might press too hard and warp the metal plate that holds it in
place.
1
* If the installed mounting sleeve is loose in the dashboard, the
pressure plates may be bent slightly to remedy the problem.
Remove the mounting sleeve from the main unit (see
“Removal” on
page 44). Slide the mounting sleeve
into the dashboard and fix it with the metal shackles.
Air ventilation hole
Detachable
Front Panel
Less than 35°
Pressure Plates*
Dashboard
This unit
Mounting Sleeve
(Included)
Bracket
Rubber Cap
(Included)
Hex Bolt
(Included)
2
When your vehicle has the Bracket, mount the long
hex bolt onto the rear panel of the CDA-9886R and
put the Rubber Cap on the hex bolt. If your vehicle
does not have the Mounting Support, reinforce the
head unit with the metal mounting strap (not
supplied). Connect all the leads of the CDA-9886R
according to details described in the
CONNECTIONS section.
• For the screw *, provide a proper screw to the chassis installing
location.
3
Slide the CDA-9886R into the dashboard. When the
unit is in place, make sure the locking pins are fully
seated in the down position. This can be done by
pressing firmly in on the unit while pushing the
locking pin down with a small screwdriver. This
ensures that the unit is properly locked and will not
accidentally come out from the dashboard.
Metal Mounting Strap
Screw
Bolt Stud
This unit
Hex Nut (M5)
Lock pin