R 3DA-W882E In-Dash CD Changer/Cassette/ DSP Receiver • OWNER'S MANUAL (page 2- page 67) Please read this manual to maximize your enjoyment of the outstanding performance and feature capabilities of the equipment, then retain the manual for future reference. OPEN EJECT COMPACT DISC CHANGER O/C CLOSE SUB W. 3DA-W882E IN-DASH CD CHANGER / CASSETTE / DSP RECEIVER 40Wx4 MODE EQ CLK TITLE FR MAX RL MIN. SOURCE BAND FLAT EQ DEMO SUR DISC LEVEL MALE FEMA. POPS • 160 ROCK NEWS SUR NORM.
English 2
English Precautions Warning This label is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions will result severe injury or death. DO NOT DISASSEMBLE OR ALTER Attempts to disassemble or alter may lead to an accident, fire and/or electric shock. KEEP SMALL ARTICLES OUT OF THE REACH OF CHILDREN Store small articles (batteries, screws, etc.) in places not accessible to children. If swallowed, consult a physician immediately.
Contents English Page 6 ....................................................................... Precautions Basic Operation 10 ......................................................Initial System Start-Up 10 ............................................... Turning Power On and Off 11 ......................................................Subwoofer On and Off 12 .................................................................. Demonstration 13 ......................................................
Contents English Page Equalizer Surround Operation 46 ........................................................ Selecting BBE Mode 47 ..................................... Sound Position Selector (S.P.S.) 48 ..................................................... DSP Surround Presets 49 ............................................................. Equalizer Presets 50 ...................................... Adjusting the Equalizer Settings 51 ...................................
Precautions English Thermal Protection Circuit +60°C –10°C Be sure the temperature inside the vehicle is between +60°C (+140°F) and –10°C (+14°F) before attempting to play a disc. If the temperature is over +60°C (+140°F), the protection circuit functions to stop the CD player, and "HITEMP" is displayed. Moisture Condensation You may notice the CD playback sound wavering due to condensation. If this happens, remove the disc from the player and wait about an hour for the moisture to evaporate.
Precautions English New Discs Center Hole Bumps Center Hole As a protective measure, the CD player will automatically eject discs that have either been inserted incorrectly or have irregular surfaces. If a new disc is ejected immediately after loading, use your finger to feel around the outer edge of the CD and its center hole. If you feel any small bumps or irregularities, this could inhibit proper loading of the disc.
Precautions English Tape Slack Check and make sure any slack in the tape is taken up before inserting the tape into the unit. A loose tape can get caught in the mechanism and cause damage to the unit and the tape itself. Tighten the tape by inserting a pencil or a similar instrument into the spindle hole and turn until all the slack has been taken up. Excessively Thin Tape C-120 type cassette tapes are not recommended for use in automobile tape players.
Precautions English Installation Location Make sure the 3DA-W882E player/receiver will not be exposed to: • • • • Direct sun and heat High humidity Excessive dust Excessive vibrations 9
Basic Operation English 1 Initial System Start-Up 1 Immediately after installing or applying power to the unit, it should be initialized. At the upper-left corner of the front panel is a small button. Using a pencil or other pointed object, press this reset button to complete the initialization procedure. Turning Power On and Off 1 1 Press the PWR button to turn on the unit. INTLZ PWR Note: The unit can be turned on by pressing any other button except the eject ( h ), O/C and CLK buttons.
Basic Operation English Subwoofer On and Off This unit is not equipped with a low pass filter. Turn on the Subwoofer Output when an amplifier having the built-in filter is connected to drive your subwoofer. 1 1 SUB W. SUBW ON MODE SUBW OFF Press and hold the SUB W. button for at least 3 seconds. With each press, Subwoofer is toggled On or Off. Notes: • Initial mode is "SUBW OFF." • Leave the "SUBW OFF" as long as the Subwoofer output is not being used.
Basic Operation English Demonstration Equalizer/surround/BBE demonstration functions are provided in this unit. 2 1 1 SOURCE DEMO 2 To end the DEMO mode, press one of EQ, SUR, and BBE buttons. EQ SUR BBE 12 Press and hold the DEMO button for at least 2 seconds to activate the DEMO mode. The unit automatically performs the following operations. 1 Equalizer scanning operation (set by the manufacturer). 2 Surround scanning operation (set by the manufacturer). 3 BBE scanning operation.
Basic Operation English Sound Guide Function This function will give audible feedback with varying tones depending upon the button pressed. 1.# 2 1 2 Press and hold the PWR button for more than 3 seconds. INTLZ PWR BEEP ON 1 BEEP OFF 3 Press the Preset 1 button and the display shows "BEEP ON." Pressing the button again turns the Sound Guide function off. "BEEP OFF" will be displayed and no tones will be heard. Press the PWR button to activate the normal mode.
Basic Operation English 1 Adjusting Volume/Balance/Fader 2 1 SUB W. VOL MODE BAL FAD 2 14 Press and release the MODE button repeatedly to choose the desired mode. Notes: • If the or button is not pressed in 5 seconds after selecting the BAL and FAD modes, the unit automatically returns to the VOL mode. • With the Subwoofer mode turned on, Subwoofer output level can be adjusted. Press the button or until the desired sound is obtained in each mode.
English Radio Operation 1 2 Manual Tuning 3 1 Press the SOURCE button to select the radio mode. SOURCE DEMO TUNER * 3D TAPE 2 F1 BAND (* Only with the CD shuttle connected.) CD SHUTTLE Press the BAND button repeatedly until the desired radio band is displayed. T.S.M. PROG F2 AM 3 F1 REW DN MANU/DISC 11 12 FF UP EQ BAND Downward 90.10 Press the [ or ] button to move downward or upward one step respectively until the desired station frequency is displayed.
English Radio Operation 1 2 Automatic Seek Tuning 3 1 4 Press the SOURCE button to select the mode. SOURCE DEMO TUNER TAPE 3D * CD SHUTTLE 2 F1 BAND (* Only with the CD shuttle connected.) Press the BAND button repeatedly until the desired radio band is displayed. T.S.M. PROG F2 AM 3 9 4 DN 16 DX F1 UP Press the 9 (TUNE) button to illuminate the DX indicator in the display. With the DX mode activated, both strong and weak stations will be tuned automatically.
English Radio Operation Manual Storing of Station Presets 1 1 1 2 3 4 5 6 1. Tune in the desired radio station you wish to store in the preset memory. 2. Press and hold any one of the preset buttons (1 through 6 ) for at least 2 seconds. The frequency display will begin to blink. 3. Press the preset button into which you wish to store the station while the display is blinking (within 5 seconds). The display stops blinking once the station has been memorized. The display shows the band, preset No.
English Radio Operation Mono/Stereo Switching 1 1 MONO 8 MONO (OFF) 18 "ST" indicator appears when a stereo station is tuned in. Press the 8 (MONO) button to switch from stereo to monaural FM reception. This will help in reducing the noise of weak FM Stereo broadcasts. In the monaural mode, the "ST" indicator turns off. Press the 8 (MONO) button again to return to the stereo mode.
English Radio Operation Automatic Memory of Station Presets 1 1 2 BAND T.S.M. F1 Press the BAND button repeatedly until the desired radio band is displayed. PROG F2 AM 2 A.MEMO 10 Press the 0 (A. MEMO) button. The frequency on the display continues to change while the automatic memory is in progress. The tuner will automatically seek and store 6 strong stations in the selected band in order of signal strength.
English Radio Operation Storing into Direct Access Preset (D.A.P.) Band A combination of radio stations from any band, AM and FM (up to 6 stations) can be manually preset onto the D.A.P. band. 1 1 7 Press the 7 (D.A.P.) button to activate the D.A.P. mode. D.A.P. D.A.P. (OFF) Press the BAND button to select FM or AM. The selected band will be displayed. To memorize stations onto the D.A.P. band, follow the steps for the automatic or Manual Storing of Station Presets section above. To cancel the D.
English Radio Operation Tuning to Preset Stations 1 2 1 Press the BAND button repeatedly until the desired band is displayed. F1 BAND T.S.M. PROG F2 AM D.A.P. 2 2 1 2 3 4 F2 5 90.10 6 Press the 7 (D.A.P.) button when the station desired was stored using the D.A.P. function. Press the station preset button ( 1 through 6 ) that has your desired radio station in memory. The display shows the band, preset number with a triangle and frequency of the station selected.
English Radio Operation 1 1 Displaying Station Titles CLK If a title has been entered for the selected station, it can be displayed in place of the frequency. The display will toggle between the frequency and title display with each press of the TITLE button. (Refer to page 23 to title stations.) TITLE 90.
English Radio Operation 2.# Titling Stations 4 1 Tune in a station to be titled. 2 3 CLK CLK Press the TITLE button twice (once if you are already in the Clock Priority mode) to select the preset station titling mode. "--------" will appear in the display. (Refer to page 22). TITLE Press and hold the TITLE button for at least 3 seconds. The first digit will blink.
English Radio Operation 5 5 Titling Stations (Continued) CLK TITLE A or/ou/o or ALPINE Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title. 6 Repeat the steps and above to complete the titling. All 8 character positions should be filled.
English Radio Operation Searching Titled Stations (Title Search Menu) 1 2 CLK BAND T.S.M. PROG TITLE F1 ALPINE Press the TITLE button to activate the Title Display mode. Press and hold the T.S.M. button for at least 2 seconds while the station title is displayed. The titled station in memory blinks in the display. c 3 Press the DN ( ) or UP ( the desired station title. f) button to select UP DN 4 BAND PROG T.S.M. Press the T.S.M. button to play the selected station.
CD Operation English Preparation for Playback 1 Insert your discs (up to 3) into the disc slots of the CD magazine with the label side facing up. CD Magazine 2 Insert the CD magazine all the way into the 3DA-W882E with the arrow pointing toward the unit as shown here. 3 To remove discs from the CD magazine, first find the lever corresponding to the CD you would like to remove. Push the lever away from the magazine. The disc will come halfway out from the CD magazine.
CD Operation 4 2 1 3 English Normal Play and Pause 4 3 1 Insert the magazine all the way as instructed on top of the magazine. 2 Press the SOURCE button repeatedly to select the 3D mode. SOURCE DEMO TUNER 3 TAPE 1 * 3D CD SHUTTLE 2 3 3 T02 0'07 DISC or REW DN MANU/DISC 11 12 FF UP (* Only with the CD shuttle connected.) Press one of the preset number buttons (1 – 3 ) to select a disc set in the magazine. The disc can also be selected with the disc select switch.
CD Operation 1 Fast Forward and Backward c 1 English f Press and hold the DN ( ) or UP ( ) button to quickly move backward or forward until you reach the desired section of the track. UP DN Repeat Play 1 1 RPT 8 (OFF) 28 Press the 8 (RPT) button to play back repeatedly the track being played. The unit enters the Repeat mode and the track will be played repeatedly. RPT ALL Press the 8 (RPT) button again to deactivate the repeat play.
CD Operation English Music Sensor (Skip) 1 1 c Momentarily press the DN ( ) button once to return to the beginning of the current track. If you wish to access a track further back, repeatedly press until you reach the desired track. DN T04 UP T05 f Press the UP ( ) button once to advance to the beginning of the next track. If you wish to access a track further ahead, press repeatedly until the desired track is reached. (The example shows the Music Sensor operation starting from track No. 4.
English CD Operation M.I.X. (Random Play) 1 1 Press the 7 (M.I.X.) button in the play or pause mode. The unit enters the M.I.X. mode and the tracks on the disc will be played back in a random sequence. After all the tracks on the disc have been played back once, the player will load the next disc and begin a new random sequence until the M.I.X. mode is canceled. M.I.X. 7 M.I.X. (OFF) To cancel M.I.X. play, press the 7 button again. (M.I.X.) Note: If a CD Shuttle equipped with the ALL M.I.X.
CD Operation English Scanning Programs 1 1 9 Press the 9 (SCAN) button to activate the Scan mode. The first 10 seconds of each track will be played back in succession. SCAN SCAN (OFF) To stop the Scan, press the 9 to deactivate the Scan mode.
English CD Operation 1 To display CD Titles 1 CLK In the 3D/CD Shuttle mode, after a title has been entered for a CD, it can be displayed by pressing the TITLE button. The display will toggle between Normal, Clock and CD Title with each press of the CLK/TITLE button (see example below). (Refer to page 33 to title the disc.
CD Operation English 1.@ Titling Disc 3 1 2 CLK CLK Press the TITLE button to select the disc-titling mode. (Refer to page 32). TITLE Press and hold the TITLE button for at least 3 seconds. The first digit will blink. TITLE or or/ou/o BLPINE 3 c UP f Press the DN ( ) or UP ( ) button to select the desired letter/numeral/symbol available for naming ("A" for example).
CD Operation 4.^ 4 English Titling Disc (Continued) CLK TITLE AL 5 Press the TITLE button to store the first character. The first character will stop blinking and the display will automatically advance to the next character. When that character begins to blink, you may choose the next letter or symbol of your title. Repeat the steps and above to complete the titling. Pressing the TITLE button after entering the eighth character, automatically stores the title into memory.
CD Operation English Erasing Disc Title 1 2 CLK Press the TITLE button to select the disc titling mode. Then, press and hold for at least 3 seconds. TITLE OPEN ALPINE O/C CLOSE Press and hold the O/C button for at least 3 seconds to activate the title scanning mode. The title in the display will blink, for example "ALPINE". c 3 f Press the DN ( ) or UP ( ) button repeatedly until the disc title you want to erase is displayed.
CD Operation English Searching Titled Discs (Title Search Menu) 1 2 CLK BAND Press the TITLE button to activate the Title Display mode. TITLE T.S.M. PROG ALPINE Press and hold the T.S.M. button while the title is displayed. The title in memory blinks in the display. c Press the DN ( ) or UP ( the desired disc title. 3 f) button to select UP DN 4 36 BAND PROG T.S.M. Press the T.S.M. button to play the selected disc. The unit will automatically search the disc and will play that disc.
English CD Shuttle Operation Operation of 6-Disc Shuttle (Option) If an Ai-NET applicable CD Shuttle made by ALPINE is connected, this unit can operate the CD Shuttle. 1 3 2 2 1 Press the SOURCE button to activate the CD Shuttle mode. The mode will change each time the button is pressed. SOURCE DEMO TUNER TAPE * 3D CD SHUTTLE 2 (* Only with the CD Shuttle connected) Press one of the buttons 1 – 6 to select a disc set in the CD Shuttle.
English CD Shuttle Operation Operation of 12-Disc CD Shuttle (Option) If an Ai-NET applicable CD Shuttle made by ALPINE is connected, this unit can operate the CD Shuttle. 1 2 1 3 Press the SOURCE button to activate the CD Shuttle mode. The mode will change each time the button is pressed. SOURCE DEMO TUNER 2 TAPE REW DN 3D MANU/DISC 11 12 * CD SHUTTLE Press the Disc Select button to select a disc set in the CD Shuttle. The disc can also be selected with the Disc Select switch.
English CD Shuttle Operation How to Use the Function Mode When the 12-disc CD Shuttle is connected, a disc can be directly selected. 2 1 1 Press the FUNC button. The FUNC indicator lights up and the unit enters the FUNC mode. FUNC FUNC 2 Press one of 7 – ] buttons and select a disc set in the CD Shuttle magazine. 7 8 9 10 DN 11 12 UP Notes: • One of discs 1-6 can be selected by pressing one of the buttons 1 – 6 regardless of the FUNC mode.
Cassette Player Operation English 1.@ Opening and Closing of the Movable Display 1 Press the O/C button. The movable display opens. OPEN O/C CLOSE 2 To close the movable display, press the O/C button again. OPEN O/C CLOSE 40 Notes: • When the movable display is opened, do not place any object on the display and be careful not to bump or apply any pressure to the door while it is open. This can cause damage to the mechanism.
Cassette Player Operation English Playback 3 1 1 2 1 When a tape cassette is inserted with the movable display opened, the display closes automatically and the playback starts. When a cassette is already inserted, press the SOURCE button to select the TAPE mode. The mode will change each time the button is pressed. SOURCE DEMO TUNER 2 TAPE 10 3D * (*Only with a CD Shuttle connected.) CD SHUTTLE PAUSE Press the 0 button to pause the tape playback. Press again to resume tape playback.
Cassette Player Operation English Dolby B/C NR (Noise Reduction) 1 1 B C NR B/C NR 7 B C NR Press the 7 (B/C NR) button in the tape mode to select the Dolby B NR or C NR to play a Dolby B NR or C NR encoded tape respectively. The B or C indicator appears in the display to show your selection. A reduction in tape hiss should also be noticed, with a properly encoded tape. To deactivate the Dolby NR mode, press the 7 (B/C NR) button until the B NR and C NR indicators disappear.
Cassette Player Operation English Fast Forward and Rewind 2 1 1 REW DN MANU/DISC 11 12 Press the REW or FF ([ or ] ) button during tape play to fast rewind or forward the tape respectively. The tape side indicator ( or ) blinks. When the end of the tape is reached in the rewind mode, the player stops automatically and begins playing from the beginning of the same side.
Cassette Player Operation English Manual Reverse 1 BAND PROG 44 T.S.M. Press the PROG button during tape play to change the direction of play. The tape side indicators ( and ) change to show which side of the cassette is being played.
Cassette Player Operation English Program Sensor (P.S.) 1 PS-1 DN PS+1 UP Press the P.S. DN button once to return to the beginning of the current selection being played. If you wish to return to a selection further back, press repeatedly until the number of selections you would like to skip is shown in the display. The display will show PS-1 with the first press and will increase by one with each successive press up to PS-9. The tape indicator will blink showing the direction of your search.
Equalizer/Surround Operation English Selecting BBE Mode The BBE (Barcus Berry Electronics) processor installed in this unit is designed to correct the phase distortion inherent in most loudspeaker designs. Ensuring the phase integrity of the signal driving the speakers improves the accurate reproduction of the sound. When used in conjunction with the equalizer and sound field effects, optimum sound space enhancement can take place.
Equalizer/Surround Operation English Sound Position Selector (S.P.S.) 2 1 1 Press the S.P.S. button for at least 2 seconds. DISP 2 This feature gives the user the ability to adjust the time delay of the 4 main speakers to provide the ideal sound stage for each listener in the car. The staging can be optimized for the front passenger, driver, front passenger and driver, or front and rear passengers and driver. S.P.S.
Equalizer/Surround Operation English DSP Surround Presets 1.@.#.$.%.^ 1 The 3DA-W882E employs DSP (Digital Signal Processing) to duplicate mathematically various listening environments. Six typical surround settings are provided for a variety of musical source material as follows. NORMAL (Flat) SUR Press the SUR (SURROUND) button to select the Surround OFF (Flat) mode.
Equalizer/Surround Operation English Equalizer Presets 1.@.#.$.%.^ 1 EQ 2 EQ 3 4 5 6 Six typical equalizer settings are preset at the factory for a variety of musical source material. Setting 1: FLAT Press the EQ (EQUALIZER) button to select the flat frequency response. Setting 2: MALE (VOCAL) Press the EQ button to select the MALE setting. Setting 3: FEMALE (VOCAL) EQ Press the EQ button to select the FEMALE setting. Setting 4: POPS EQ Press the EQ button to select the POPS setting.
Equalizer/Surround Operation English Adjusting the Equalizer Settings You can modify the Equalizer settings to create a response curve more appealing to your personal taste. 1 EQ EQ 2 FLAT ---------REW DN MANU/DISC 11 12 FF UP Press the EQ (EQUALIZER) button repeatedly to select the Equalizer setting preset which you wish to adjust. The example shows FLAT mode. Within 5 seconds after the operation of , press the EQ BAND DN ( [ ) or UP (] ) button to select the frequency band to adjust.
Equalizer/Surround Operation English Memorizing the Equalizer Settings 1 Press the EQ button to select the desired equalizer setting (factory preset or your own) you wish to store in memory. EQ 2 EQ 1 2 SUR 3 Within 5 seconds after operating step , press and hold any one of the Preset buttons (1 – 6 ) for at least 2 seconds. The indicators blink for 5 seconds showing the unit is ready for storing.
Equalizer/Surround Operation English Recalling the Memorized Equalizer/Surround Settings 1 BBE EQ 1 Press the desired mode button, EQ, SUR or BBE. SUR BBE 2 USER PRESET 1 2 3 4 5 6 To recall your preset, pressing one of the preset switches (1 – 6 ) within 5 seconds after the operation in Section . This provides sound characteristics of your own design. Switching the Display Modes Press the DISP (DISPLAY) button to select the desired Display pattern mode. 1 DISP 52 S.P.S.
Equalizer/Surround Operation Pattern Display English Description EQ Pattern 1 • 63 • 160 • 400 • 1K • 2.5K • 6.3K • 16K • 2 Spectrum Analizer Pattern • 63 • 160 • 400 • 1K • 2.5K • 6.3K • 16K • 3 Peak Hold Pattern • 63 • 160 • 400 • 1K • 2.5K • 6.3K • 16K • 4 Peak Value Increasing Pattern • 63 • 160 • 400 • 1K • 2.5K • 6.3K • 16K • 5 "i" Character Pattern • 63 • 160 • 400 • 1K • 2.5K • 6.
Clock Operation 1.@ Displaying Time 1 12:00 CLK 2 54 English TITLE CLK Press the CLK (Clock) button to display the time. The unit displays the time. Note: Selecting any tuner or CD function while in the clock mode will interrupt the time display momentarily. The function selected will be displayed for about 5 seconds before the time returns to the display. The time will be displayed even with power to the head unit turned off, as long as the ignition key is on.
Clock Operation 1 English Setting Time 2 3 4 1 2 CLK TITLE 12:30 12:00 CT 4 3 4 Make sure you are in the Clock mode by pressing the Clock button (see page 54). Then, press and hold the CLK (Clock) button for at least 3 seconds. The time indication will begin to blink. To set the time to the nearest hour, press the CT button while the time indication is blinking. For example, if the time shown in the display is 9:35, the CT function will change it to 10:00.
Remote Control English Controls 1 Mute Button Press the button to lower the volume by 20 dB instantly. Press the button again to cancel. VOLUME 1 2 3 4 5 6 7 MUTE PWR 2 Power Switch Press the switch to turn the power on/off. 3 ENT CD-CHG BAND PROG SOURCE REMOTE CONTROL UNIT A.PROC k Button Press the button to switch between the Play and Pause modes for the tape player or CD. 4 CD Changer Button Press the button to change to the CD changer operation.
Remote Control 8 VOLUME 9 MUTE PWR 8 9 p ENT CD-CHG BAND PROG w SOURCE REMOTE CONTROL UNIT A.PROC q p English Button Radio mode: SEEK (DN) Button Tape mode: REW Button 3D/CD Shuttle mode: Press the button to go back to the beginning of the current track. Button Radio mode: SEEK (UP) Button Tape mode: FF Button 3D/CD Shuttle mode: Press the button to advance to the beginning of the next track.
Remote Control English Battery Replacement Applicable battery: Use two UM-4 or equivalent. Opening the battery cover Slide out the battery cover while firmly pressing outward. d e Replacing the battery Put the batteries in the case as illustrated. d e Closing the cover Push the cover as illustrated until a click is heard.
Disc Care English Correct Handling CORRECT INCORRECT Do not drop the disc while handling. Hold the disc so you will not leave fingerprints on the surface. Do not affix tape, paper, or gummed labels on the disc. Do not write on the disc. CORRECT Disc Cleaning Fingerprints, dust, or soil on the surface of the disc could cause the CD player to skip. For routine cleaning, wipe the playing surface with a clean, soft cloth from the centre of the disc to the outer edge.
In Case of Difficulty English If you encounter a problem, please review the items in the following check list. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Initial Turn-on After Installation 60 Symptom Cause and Solution No function or display. • Car's ignition is off. – If connected per instructions, the unit will not operate with the car's ignition off.
In Case of Difficulty English Radio Mode Symptom Cause and Solution Unable to receive stations. • No antenna or open connection in cable. – Make sure the antenna is properly connected; replace the antenna or cable if necessary. Unable to tune stations in the seek mode. • You are in a weak signal area. – Make sure the tuner is in the DX mode. If the area you are in is not known to be a weak signal area, the antenna may not be grounded and connected properly.
In Case of Difficulty English CD Mode Symptom Cause and Solution CD not functioning. • Out of operating temperature range +50°C (+120°F) for CD. – Allow the car's interior (or trunk) temperature to cool. CD playback sound is wavering. • Moisture condensation in the CD Module. – Allow enough time for the condensation to evaporate (about 1 hour). Unable to Fast-Forward or Backward. • The CD has been damaged.
In Case of Difficulty English Indication for 3D Head Unit Indication Cause and Solution • Protective circuit is activated due to high temperature. – The indicator will disappear when the temperature returns to within operation range. • No disc is loaded. – Select a disc. • No magazine is loaded. – Insert a magazine. • Malfunction in the unit. – Press the eject button and remove the CD from the CD magazine. Inspect the CD for any deformities or irregularities (see pages 6 – 7).
In Case of Difficulty English Indication for CD Shuttle Indication Cause and Solution • Protective circuit is activated due to high temperature. – The indicator will disappear when the temperature returns to within operation range. • Malfunction in the CD Shuttle. – Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication. Insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. • Magazine ejection not possible.
Specifications English FM TUNER SECTION Tuning Range ...................................................................................................... 87.5 – 108.0 MHz Mono Usable Sensitivity ........................................................................... 9.3 dBf (0.8µV/75 ohms) 50 dB Quieting Sensitivity ...................................................................... 13.5 dBf (1.3µV/75 ohms) Alternate Channel Selectivity ............................................................
Specifications English TAPE PLAYER SECTION Tape Speed ....................................................................................... 1-7/8 ips (4.8 cm/sec) ±0.7% Wow & Flutter ........................................................................................................................ 0.06% Tape Signal-to-Noise Ratio With Dolby B NR On/Off ............................................................................................. 68/60 dB With Dolby C NR On/Off/ .....................
Specifications English REMOTE CONTROL Battery Type ................................................................................................. "AAA" sized dry battry Battery Quantity .............................................................................................................................. 2 Dimensions (W x H x D) .................................... 56mm (2-1/4") x 14mm (9/16") x 105mm (4-1/8") Weight (without battery) .............................................................
