HORIZONTAL DIAPER CHANGING STATION ALP411-E USER GUIDE
THANK YOU FOR YOUR PURCHASE. Known in the industry for excellent products, Alpine Industries is a manufacturer of innovative, solution-based products for the commercial and institutional markets worldwide. Combining commitment to the customer, design innovation and skilled, dedicated workforces, they have produced a range of products that are an essential part of every commercial facility.
Table of Contents 1 Parts Included 2 Hardware Bag 3 Installation Instructions 9 Operation Instructions 10 Maintenance and Cleaning 11 Limited Warranty 12 Disclaimer
Parts Included 1 CHANGING STATION 2 DOOR/WALL PLATE Tools Required (Not Included) Adult Installation Required • • • • Level Measuring Tape Power Drill with 7/32”, 1/8” and ½” masonry bits. P ower screwdriver with bull nose Philips bit. CAUTION: • Read all instructions before assembly of Diaper Changing Station.
Hardware A 3” WOOD SCREWS (4) B 3/4” FINISHING WASHERS (4) C 3” MACHINE SCREWS (2) D 3/4” FLAT WASHERS (4) E TOGGLE ANCHORS (2) F 1 ¼” CAPS (4) 2
Installation Instructions ! WARNING: • One wall stud MUST be located and USED for at least one side of the diaper changing station. • The diaper changing station CANNOT be heavier than the anchors or walls they are attached to. • It MUST be firmly secured to support the additional weight of a child. • Contact an architect or building contractor for further questions. STEP 1: A. Locate the wood stud where the left side of Changing Station (1) will be mounted to the wall. STEP 2: A.
Installation Instructions FIGURE A WALL WOODEN WALL STUD 1 D B A 4
Installation Instructions NOTE 2: FOR USE WITH TOGGLE ANCHORS (E): • If the finished wall surface has wood studs that are not 16” on center, has metal studs, or has an underlying surface of concrete block, use ½” bit. • Use Machine Screws (C) and Flat Washers (D) (See Figure B on page 6). • For holes NOT located in a wood stud, Toggle Anchors (E) MUST be used (See Figure C on page 7). See “Using Toggle Anchors” section. STEP 6: A.
Installation Instructions FIGURE B WALL 1 WOODEN WALL STUD E D C 6
Installation Instructions USING TOGGLE ANCHORS: 1. Insert the metal end of the Toggle Anchor (E) into the 1/2’’ hole. 2. Slide zip strip down snugly against the wall. 3. Snap off break-away pieces of Toggle Anchor (E) (See Figure C below). 4. Ensure all four (4) screws are tight and snap Caps (F) over screw heads. 5. A lign holes on the Changing Station (1) with Toggle Anchors (E) and secure top left corner of the Changing Station (1) to the wall using Machine Screws (C) and Flat Washers (D). 6.
Installation Instructions RECOMMENDED BLOCKING 1. If the walls do not have studs on center, additional blocking is necessary (See Figure D below). 2. Contact an architect or building contractor to make sure the blocking is adequate and complies with building codes. FIGURE D 7.2 in. / 183mm 18.1 in.
Operation Instructions 1. Rotate base downward and place the infant on top of the changing surface. 2. Use restraint system as described below. After the child has been changed, remove the restraint system, and rotate the base back up against the wall. USING THE RESTRAINT SYSTEM: 1. Place the child so that the restraint strap is located at the abdomen. 2. Rotate the top of the buckle upward and insert the strap in the buckle. 3. Pull the strap through the buckle until snug against the infant. 4.
Maintenance and Cleaning 1. Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. 2. Do not use any strong chemical cleaners or cleaning agents that may be hazardous to children. 3. Check all hardware and components monthly or as required to ensure the hardware is tight and there are no missing or damaged pieces. 4. Take unit out of service if any element is missing or damaged and contact customer service to order replacement parts.
Limited Warranty 1. Alpine Industries (the company) warrants to the purchaser that the product will be free from defects in workmanship and materials for a period of one (1) year from the date of purchase. 2. These warranties are not assignable or transferable to any other person. 3.
Disclaimer By purchasing products from Alpine Industries, user agrees as follows: TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE PRODUCTS AND INFORMATION ON THIS SITE IS PROVIDED “AS IS” AND WITH ALL FAULTS AND ALPINE INDUSTRIES.
ALP411-E 27 Selvage Street • Irvington, NJ • 07111 • © 2021 Alpine Industries. alpineindustries.
