User manual

49-EN
Before performing the following procedures, refer to “About Time
Correction” (page 51).
1 Touch the title bar of Time Correction.
The Time Correction adjustment screen appears.
2 Touch [ ] or [ ] of the desired speaker to adjust
the distance.
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 51.
3 Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the
listening position at the same time as the sound of other
speakers.
You can change the unit, (cm or inch) of time correction.
Setting item: T.Corr Parameter
Setting contents: cm / Inch
You can modify the equalizer settings to create a response curve more
appealing to your personal taste.
Setting item : G-EQ
1 Select L+R by touching [ ] of G-EQ.
When Parametric EQ is adjusted, this setting will be turned
OFF.
2 Touch the title bar of G-EQ after selecting L+R.
The G-EQ list screen appears.
3 Adjust the G-EQ to your preference.
Selecting the Band
Touch [ ] or [ ] of Band to select the band to be adjusted.
Band-1 (63 Hz) / Band-2 (150 Hz) / Band-3 (400 Hz) /
Band-4 (1 kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
Adjusting the Level
Touch [ ] or [ ] of Level to adjust the level of selected
band.
Adjustable output level: –6 to +6 dB
4 To adjust another band, repeat step 3, and then
adjust all bands.
• When Graphic EQ is adjusted, the adjustment for Parametric EQ
becomes ineffective.
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
Setting item : P-EQ
1 Select L+R by touching [ ] of P-EQ.
When Graphic EQ is adjusted, this setting will be turned
OFF.
2 Touch the title bar of P-EQ after selecting L+R.
The P-EQ list screen appears.
3 Adjust the P-EQ to your preference.
Selecting the Band
Touch [ ] or [ ] of Band to select the band to be adjusted.
Band 1 / Band 2 / Band 3 / Band 4 / Band 5
Adjusting the Frequency
Touch [ ] or [ ] of Freq. to adjust the frequency of the
selected band.
Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps)
Band-1: 20 Hz~80 Hz (63 Hz)
Band-2: 50 Hz~200 Hz (150 Hz)
Band-3: 125 Hz~3.2 kHz (400 Hz)
Band-4: 315 Hz~8 kHz (1 kHz)
Band-5: 800 Hz~20 kHz (2.5 kHz)
Adjusting the Level
Touch [ ] or [ ] of Level to adjust the level of selected
band.
Adjustable level: –6 to +6 dB
Setting the Bandwidth
Touch [ ] or [ ] of Q to select the bandwidth.
Adjustable bandwidth: 1, 1.5, 3
4 To adjust another band, repeat step 3 and adjust all
bands.
• When the Parametric EQ is adjusted, the adjustment for Graphic EQ
becomes ineffective.
• The frequencies of adjacent bands cannot be adjusted within 4 steps.
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
Adjusting the Time Correction (Time
Correction)
Setting the Time Correction Unit
(T.Corr Parameter)
cm: Time correction value is in cm.
Inch: Time correction value is in inches.
Graphic Equalizer Adjustments (G-EQ)
L+R: Sets the same adjustment values for the left and right
channels.
Adjusting the Parametric Equalizer Curve
(P-EQ)
L+R: Sets the same adjustment values for the left and right
channels.