User manual

86 -EN
Error Messages
Various messages are displayed on the screen during operation. In
addition to the messages telling you the current status or providing
guidance for the next operation, there are also the following error
messages. If one of these error messages is displayed, carefully
follow the instructions in the solution column.
System
If you are driving, please pull over before using this function.
• A setup operation, etc., was carried out while the vehicle was
running.
-Move the vehicle to a safe location, stop, and engage the parking
brake, then carry out this operation.
USB current error.
• Abnormal current is run to the USB connector device.
-Turn the ignition key off, and then set to ON again.
-Attempt to connect another iPod/iPhone/Android Phone/USB
Flash drive.
USB HUB is not supported.
• A USB ash drive with a hub is connected.
-You cannot play back from a USB ash drive with a hub. USB
hub connections are also not supported.
File Format not supported.
• A USB Video le that is not supported by this unit is selected.
-Check if the video file is playable by seeing "Supported USB
Video Format" (page 42).
Audio/Visual
Connected USB device is not supported.
• An iPod/iPhone/Android Phone that is not supported by the unit is
connected.
- Connect an iPod/iPhone/Android Phone that is supported by the unit.
- Reset the iPod.
• A USB device that is not supported by the unit is connected.
- Attempt to connect another USB ash drive.
• Communication error.
- Turn the ignition key off, and then set to ON again.
- Check the display by reconnecting between the iPod/iPhone/Android
Phone and the unit, using the iPod/iPhone/Android Phone cable.
- Check the display by reconnecting between the USB ash drive and the
unit.
• Caused by the iPod/iPhone/Android Phone Software Version not being
compatible with this unit.
- Update the iPod/iPhone/Android Phone Software Version to be
compatible with this unit.
• The iPod/iPhone/Android Phone is not veried.
- Change to another iPod/iPhone/Android Phone.
No data.
• There are no data in the iPod/iPhone/Android Phone.
- Download data to the iPod/iPhone/Android Phone and connect to the
unit.
• There are no data in the USB ash drive.
- Download data to the USB ash drive and connect to this unit.
Un-readable song was skipped.
• A copy-protected WMA le has been detected.
- You can only play back non-copy-protected les.
• A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate supported by the unit.
DAB Antenna error
• The DAB antenna cable is either damaged or not connected
correctly to the product.
-Check that the antenna cable is not kinked or otherwise
damaged. Replace the antenna if necessary.
• Abnormal current is run to the DAB Antenna.
-Connect the antenna properly to a car with a 12 volt negative
ground.
Bluetooth
Please connect Bluetooth audio device.
• The Bluetooth audio device was not connected correctly.
-Check the settings for the unit and the Bluetooth audio device
and reconnect.
Unable to download phonebook.
• Phonebook failed to read due to mobile phone disconnection, etc.
-Check the mobile phone connection, and then conduct
synchronising and adding again. (See page 58)
• The connected mobile phone does not support synchronising of its
phone book.
-Connect the mobile phone that supports synchronising the phone
book, then synchronise again. (See page 58)
HDMI
HDMI communication error.
Please check your device and operate it again.
• Communication error.
-Turn the ignition key off, and then set to ON again.
-Check the display by reconnecting between the HDMI and the
unit, using the HDMI cable.
-Check the display by reconnecting between the HDMI device and
the unit.
HDMI current error.
Please Connect your device again.
• Abnormal current is run to the HDMI connector device.
-Turn the ignition key off, and then set to ON again.
-Disconnect the HDMI device from the unit, and then reconnect it.
HDMI monitor communication error.
Please check the connection or ACC off / on.
• HDMI device communication error.
-Turn the engine (ACC) OFF/ON. Or, check the HDMI cable
where it connects to the HDMI monitor.
Monitor connect via HDMI has been exceeded.
Please check the connection.
• More than 4 HDMI monitors are connected.
• A cascade connection using more than 2 distributors is made.
-Use one distributor and less than 4 HDMI monitors when
connecting.