Owner`s manual
1
I
5.4 lnstallThe
Panel
CAUTION
Never
put
the
panel
face
wall, or
on bulgy
objects.
Never
crash or
strike it.
down on floor
or against the
Remove
the
air-in
grill.
Slide two
grill
switches toward
the middle at the same time,
and then
pull
them up.
(Referto
Fig.5-9)
Draw
the
grill
up to
an angle of
about
451
and
remove it.
(Referto
Fig.5-10)
Remove
the
installation
covers
at the
four
corners
Wrench
off the bolts,
loose the rope
of the installation covers,
and remove
them.
(Referfo
Fiy
5a1)
lnstall
the
panel
Align the
swing motor
on the
panel
to the tubing
joints
of the
body
properly.
(
Referto
Fig.sa)
Fix
hooks
of the
panel
at swing motor
and its opposite sides
to the
hooks
of corresponding
water receiver.
(
Refer
to
Fig.5-12.1)
Then hang
the other two
panel
hooks
onto
corresponding
hangers
ofthe body.
(
Referto Fig.5-12.2)
CAUTION
Do
not coil
the
wiring
of the
swing
motor into
the seal
sponge.
lnstall
the
distribution
duct
Conditioned
air can
be distributes by means of
a distribution duct.
Distribution duct
-
Adjust
the four
panel
hook
screws to keep
the
panel
horizontal,
and
screw
them
up to the ceiling
evenly.
(
Refer
fo
Fig.+12.3)
Regulate
the
panel
in the
direction
of the
arrow in
Fig.5-12.4
slightly
to fit the
panel's
center
to the
center
of the
ceiling's
opening.
Guarantee
that hooks
of
four
corners
are
fixed well.
Keep
fastening
the
screws
under
the
panel
hooks,
until the
thickness
of the
sponge
between
the
body
and the
panel's
outlet has
been reduced
to
about 4-6mm.
The
edge of the
panel
should
contact with
the
ceiling well.
(Refer
to Fig.S-l3)
.
Malfunction
described
in
Fig.S-14
can
be caused
by
inappropriate
tightness
the
screw.
.
lf
the
gap
between
the
panel
and
ceiling still
exists after
fastening
the screws,
the
height
of the indoor
unit should
be modified
again. (
Refer
to Fig.5-11-left)
'
You
can modify
the height
of the
indoor
unit through
the
openings
on
the
panel's
four
corners, if
the lift of
the
indoor
unit
and the
drainpipe is
not influenced
(Refer
to
Fig.5-16-right).
Hang
the air-in
grill
to the
panel,
then
connect
the lead
terminator
of the
swing motor
and that of
the control
box
with
corresponding
terminators
on the
body respectively.
Relocate
the air.in
grill
in
the
procedure
of reversed
order.
Relocate
the installation
cover.
Fasten
the rope
of installation
cover on the
bolt
of the
installation cnver. (Refer
to
Fig.5-16-lett)
Press
the installation
cover
into the
panel
slightly.
(Refer
to
Fig.5-16-nght)
Fresh
air intake (O75)
Distribution
duct
Distribution duct
-
Fig.il20
2
I
3
I
6
I
5.5
illil
Disrriburionducr
lllll
installation
manual
7