User Guide

ManualsBrandsALPHACOOL ManualsWater CoolingALPHACOOL Core Hurrican Water Cooling Set

ACCESSORIES ZUBEHÖR ACCESSOIRES

ALPHACOOL CORE HURRICAN WATER COOLING SET

Lisez les instructions de sécurité avant de commencer l‘installation.

Lesen Sie die Sicherheitshinweise, bevor Sie mit der Installation beginnen.

Read the safety instructions before starting the installation.

Eisblock XPX Edge Aurora

Fitting Eiszapfen Pro 16mm G1/4

Fitting Eiszapfen L - Connector G1/4

EN DE FR

ACCESSORIES ZUBEHÖR ACCESSOIRES

Eisbecher Aurora D5 250mm

Alphacool VPP Pump

ATX 24-pin jumper plug

EN DE FR

aRGB Controller: Aurora Eiscontrol

Digital RGB LED Y-splitter 3-times cable

PWM to 2x PWM connector cable

Only: Core Hurrican 240mm XT45 water cooling Set

Summary of content (7 pages)

PAGE 1
ALPHACOOL CORE HURRICAN WATER COOLING SET EN Read the safety instructions before starting the installation. ! DE Lesen Sie die Sicherheitshinweise, bevor Sie mit der Installation beginnen. ! FR Lisez les instructions de sécurité avant de commencer l‘installation.
PAGE 2
1. COMPONENT STRUCTURE KOMPONENTEN AUFBAU STRUCTURE DES COMPOSANTS 2. VPP PUMP VPP PUMPE POMPE VPP DE FR 1x 1x NexXxoS XT45 Full Copper 240mm Radiator NexXxoS XT45 Full Copper 360mm Radiator Only: Core Hurrican 360mm XT45 water cooling Set, V.2 V.
PAGE 3
. RADIATOR PREPARATION RADIATOR VORBEREITUNG PRÉPARATION DES RADIATEURS ALPHACOOL CORE HURRICAN XT45 WATER COOLING SETS Close all unused ports of the radiator with the screw plugs. 4. XPX ASSEMBLY DE Verschließen Sie alle ungenutzten Öffnungen des Radiators mit den Verschlussschrauben. XPX MONTAGE DE Mount the XPX cooler on your mainboard. The exact installation can be found in the instructions enclosed with the XPX cooler. Montieren Sie den XPX Kühler auf ihr Mainboard.
PAGE 4
ALPHACOOL CORE HURRICAN 420MM XT45 WATER COOLING SET 8. 7. HARDTUBE CONNECTION THE LEDS CONNECTING HARDTUBE LEDS ANSCHLIESSEN ANSCHLUSS CONNEXION LES LEDS CONNECTERHARDTUBE Digital-RGB adapter Fans / Lüfter / Ventilateurs Power supply / Netzteil / alimentation électrique Digital RGB LED Y-splitter 3-times cable aRGB Controller: Aurora Eiscontrol EN DE FR Usually the radiator is mounted in the top or in the front.
PAGE 5
4. 5. 6. EN DE FR 1. Measure the straight paths exactly and cut the HardTubes exactly to size. If you want to bend the HardTube, cut it only after bending. 2. Deburr the outside of the HardTube until a clean bevel is formed. Deburr the inner area only so far that all chips are removed. 3. Moisten the silicone insert with water and push it into the HardTube. 4. Push the HardTube into the bending tool. 5. Heat the HardTube evenly over an area of approx.
PAGE 6
10. WATER FLOW DIRECTION WASSERFLUSSRICHTUNG DIRECTION DU FLUX D'EAU 11. COOLANT KÜHLFLÜSSIGKEIT LE CALOPORTEUR EN DE FR Connect the pump to your power supply. Set your power supply unit to OFF at the switch and plug the ATX jumper plug into the 24-pin power cable of the power supply unit. Now fill the reservoir. When you set the power supply unit to ON at the toggle switch, the pump will start and the water will be pumped into the cooling circuit.
PAGE 7
12.