User Manual

79
746-257-B5-001, Rev. A1 (11/2013)
Parameter OID Description Access Type Value
ENVIRONMENTAL CONTROL CONNECTOR, continued
atiMgmtSysIOSysIOPinCtrl 1.3.6.1.4.1.926.1.3.2.8.20.0 Control of Output Pin Read/Write Integer 1=contactOpen
2=contactClosed
atiMgmtSysIOSysIOPinIn4 1.3.6.1.4.1.926.1.3.2.8.21.0 Status of Input Pin 4 Read Only Integer 1=contactOpen
2=contactClosed
atiMgmtSysIOSysIOPinIn5 1.3.6.1.4.1.926.1.3.2.8.22.0 Status of Input Pin 5 Read Only Integer 1=contactOpen
2=contactClosed
atiMgmtSysIOSysIOPinIn6 1.3.6.1.4.1.926.1.3.2.8.23.0 Status of Input Pin 6 Read Only Integer 1=contactOpen
2=contactClosed
PLATFORMS
atiProductPlatforms 1.3.6.1.4.1.926.1.4 Object Identier
atiBroadbandUPS 1.3.6.1.4.1.926.1.4.1 Object Identier
atiBBSysView 1.3.6.1.4.1.926.1.4.1.1 Object Identier
atiBBSysViewSelects 1.3.6.1.4.1.926.1.4.1.1.1 Object Identier
atiBBSysViewSelfTestControl 1.3.6.1.4.1.926.1.4.1.1.1.1.0 Starts/Stops a system Self Test Read/Write Integer 1=Stop
2=Start
atiBBSysViewSelfTestInhibit 1.3.6.1.4.1.926.1.4.1.1.1.2.0 System Self Test is prevented. On reset, the IDH4
gets this value from the master XM3 (in a system
with more than one power supply).
Read/Write Integer 1=Normal (default)
2=Inhibited
atiBBSysViewSystemControlMgr 1.3.6.1.4.1.926.1.4.1.1.1.3.0 If the System Control Manager is running, the Small
System Controller/Administrator (SSC or SSA)
is running and there is coordination between the
power supplies for charging, testing, etc. The value
of this item is stored in non-volatile memory.
Read/Write Integer 1=Running
2=Disabled
atiBBSysViewFactoryDefaults 1.3.6.1.4.1.926.1.4.1.1.1.4.0 Will set all parameters back to the factory default
value
Read/Write Integer 1=Normal
2=Reset
SYSTEM ALARMS
atiBBSysViewAlarms 1.3.6.1.4.1.926.1.4.1.1.2 Object Identier
atiBBSysViewMajorAlarm 1.3.6.1.4.1.926.1.4.1.1.2.1.0 Indicates if any of the items monitored are in a major
alarm state
Read Only Integer 1=OK
2=Alarm
atiBBSysViewMinorAlarm 1.3.6.1.4.1.926.1.4.1.1.2.2.0 Indicates if any of the items monitored are in a minor
alarm state
Read Only Integer 1=OK
2=Alarm
atiBBSysViewSelfTestResult 1.3.6.1.4.1.926.1.4.1.1.2.3.0 If any of the items being monitored indicate that Self
Test failed, this item indicates a failure.
Read Only Integer 1=OK
2=Fail
atiBBSysViewTempProbeStatus 1.3.6.1.4.1.926.1.4.1.1.2.4.0 If any of the devices being monitored indicate a
temp probe failure or absence, this item will alarm.
Read Only Integer 1=OK
2=Missing
atiBBSysViewInputStatus 1.3.6.1.4.1.926.1.4.1.1.2.5.0 If ALL the items being monitored indicate no AC, this
item will alarm.
Read Only Integer 1=OK
2=No AC Present
SCALARS
atiBBSysViewScalars 1.3.6.1.4.1.926.1.4.1.1.3 Object Identier
atiBBSysViewInputVoltage 1.3.6.1.4.1.926.1.4.1.1.3.1.0 Power supply input voltage Read Only Integer
atiBBSysViewInputFrequency 1.3.6.1.4.1.926.1.4.1.1.3.2.0 Power supply input line frequency Read Only Integer
atiBBSysViewInputCurrent 1.3.6.1.4.1.926.1.4.1.1.3.3.0 Power supply input current Read Only Integer
atiBBSysViewBatteryVoltage 1.3.6.1.4.1.926.1.4.1.1.3.4.0 Battery voltage Read Only Integer
atiBBSysViewBatteryTemperature 1.3.6.1.4.1.926.1.4.1.1.3.5.0 Battery temperature (Degrees C) Read Only Integer
atiBBSysViewChargerCurrent 1.3.6.1.4.1.926.1.4.1.1.3.6.0 Sum of charging current from all power supplies Read Only Integer
atiBBSysViewChargerVoltsFloat 1.3.6.1.4.1.926.1.4.1.1.3.7.0 Battery charger oat voltage Read/Write Integer
atiBBSysViewChargerVoltsEqualize 1.3.6.1.4.1.926.1.4.1.1.3.8.0 Battery charger equalization voltage Read/Write Integer
atiBBSysViewChargerVoltsTemperatureComp 1.3.6.1.4.1.926.1.4.1.1.3.9.0 Battery charger temperature compensation
(0 to 5mV/Cell/°C)
Read/Write Integer
atiBBSysViewBatteryCapacity 1.3.6.1.4.1.926.1.4.1.1.3.10.0 Battery string capacity (Amp hours) Read/Write Integer
DETECT 6V BATTS
atiCibDiscTable 1.3.6.1.4.1.926.1.2.1.1.1.5.
14.0.11
Controls the ability to detect and report 6 Volt
batteries
Read/Write Integer 0 = default
1 = Detect 6 Volt
Batteries
10.1 Denitions and Settings, continued
10.0 Alpha MIB Parameters, continued