Programming instructions

ManualsBrandsAlpha Communications ManualsHome building and DecorSTR QwikBus TT33-2

AWD169 Rev. 2 (12/2012)

42 Central Drive, Farmingdale NY 11735-1202

(631) 777-5500 Fax: (631) 777-5599

TOLL-FREE Technical Line 1-800-666-4800

Email:info@alphacommunications.com

Typical Wiring Diagram and programming

for the FS1000 series 2-wire QwikBUS™

apt. intercom stations to a single entrance

pushbutton door station.

NOTES:

1. See the QwikBUS™ system programming instructions for system programming of stations and devices.

2. BUS wiring to the FS1000 series apt. stations shouls be tiwtsed pair #18AWG (non shielded) and polarity is not

important to the FS1000 stations.

3. The 12VAC door opener can be connected to the SP333 OR the TSMB3, but you must select DIP Switch #3 on the

TSMB3 accordingly.

4. See the individual system wiring diagram(s) and manual(s) for the balance of system wiring requirements.

5. All wiring shall be #18AWG minimum. See pages 2 thru 5 for programming and other system information.

6. Terminal connections shown may not be in the actual order they appear on the equipment.

Summary of content (5 pages)

PAGE 1
NOTES: 1. See the QwikBUS™ system programming instructions for system programming of stations and devices. 2. BUS wiring to the FS1000 series apt. stations shouls be tiwtsed pair #18AWG (non shielded) and polarity is not important to the FS1000 stations. 3. The 12VAC door opener can be connected to the SP333 OR the TSMB3, but you must select DIP Switch #3 on the TSMB3 accordingly. 4. See the individual system wiring diagram(s) and manual(s) for the balance of system wiring requirements. 5.
PAGE 2
The Matrix – Wiring Pushbuttons to the TT33-2 When using an STR Modular Button assembly, the system can read which switch is being pressed by electronics built into the switches. In the case of a Custom Panel, these electronics are built into the TT33-2 and you must run wires to assign each button to a position in a matrix. Modular Button Assy. Close up of TT33-2 Matrix Connections The matrix consists of Common Connections a,b,c, & d and numbers 1 through 6.
PAGE 3
The IC2 Database Chip The QwikBus™ system has 8 pin nonvolatile IC chips located on the back of each TSMB3 Speaker Microphone Module (in the Modular style Entry Panels) or TT33-2 Speaker Microphone Module (in the Custom style Entry Panels). Each unit has this chip which maintains the programming for that specific entry. If you have to replace a TSMB3 or TT33-2 unit, you can remove the IC2 from the old unit and install it into the new unit so you do not have to reprogram that entrance.
PAGE 4
PROGRAMMING SECTION for OPEN VOICE STYLE NOTE: Depending on your choice of Entry Panel, you will either be using a TT33-2 or TSMB3 Module. The TT33-2 and the TSMB3 will both be referred to in this section as the Speaker/Microphone Programming the QwikBus™ System -- Open Voice (FS1000 series) Programming the system is easily done with two installers. One to move from apartment to apartment working with the monitors, and one to be at the entry panel pressing the corresponding buttons. 1.
PAGE 5
USER Operation of the FS1000 Audio only intercom stations General Operation After a visitor has rung the bell at the entrance, the monitor will turn on automatically. You can push the ON/OFF button and talk with the visitor. You are also able to activate the door opener. Pushing the ON/OFF button will end the communication and the monitor will turn off automatically. You can switch on the monitor at any time by pressing the ON/OFF button. To switch off the monitor hold the ON/OFF button for approx.