A L PH A O NE e l ong a ted Components 01 Parts List 02 Pre-Installation 03 Installation Procedure 04 Installation Procedure (cont) 05 Operation 06 Cleaning and Maintenance 07 Self Diagnosis and Specs 08 Warranty 09 Warranty (cont) 10
ALP H A ON E Components Seat release tab Metal water inlet on the left Lid Control lever Seat T-Valve adaptor (supplied) Front (bidet) wash spray nozzle Rear wash spray nozzle Bidet supply hose (supplied) Water supply hose Shutoff valve 1
ALP H A ON E Parts List 1.Main body 2. Installation components Metal mounting bolts (2) Mounting brackets (2) Rubber expansion nuts (2) Catch plate Plastic mounting bolts (2) Butterfly Nut (2) Mounting brackets (2) Catch plate Note: There are two methods for installation. The recommended way is using the rubber expansive nuts. The second option is using the butterfly nuts. Please select the option best suited for your specific installation needs. 3. T-Valve adaptor 4. Water supply hose 5.
ALP H A ON E Please make sure you read the instructions carefully and install it properly. Caution 1. The water pressure limit is from 10 to 110 PSI. Please use as instructed. 2. The water shutoff valve should be near where the product is installed. Product Installation Procedure Pre-installation 1. Insert the mounting bolts into the rectangular steel mounting brackets. 2. Insert the mounting bolts with the brackets into the catch plate. 3.
ALP H A ON E Installation Procedure First installation method (recommended) 1. Completely remove the old toilet seat & lid 2. Install expansion nuts. Be sure to firmly press down so the top of the expansion nut is flush with the ceramic toilet surface. Old toilet seat 4.Install the bidet seat 3.Attach the catch plate Line up the bidet with the catch plate then push the bidet seat onto the catch plate. You will hear the bidet seat click into the place. Attach the catch plate in the toilet seat holes.
ALP H A ON E Connecting Water Supply 2. Unscrew water supply hose from water tank. Place towel below tank to catch any dripping water. 1. Close the water supply valve. Flush toilet. Unscrew to remove 3. Using finger nut, attach T-Valve to water tank where you removed the water supply hose. 4. Re-attach water supply hose to bottom of T-Valve. Finger nut 5. Connect the bidet supply hose to the metal inlet on the side of the bidet seat.
ALP H A ON E STOP Return the lever to the upright position to turn it off. BIDET (FRONT FEMININE WASH) Gradually push control lever forward until prefered pressure is reached. REAR WASH Gradually push control lever back until prefered pressure is reached.
ALP H A ON E Cleaning and Maintenance 1. Cleaning the exterior of the bidet seat 2. Cleaning the spray nozzles Use a smooth sponge/cloth with water and/or mild soap to clean the product. Do not use the following types of cleaning products: hydrogen chloride detergent, paint thinner,benzene abrasive paper,polishing agent, bleach, or chlorine. Pull out the nozzle softly and use a smooth cloth/sponge or soft toothbrush to clean the nozzle Paint thinner Chlorine Abrasive paper 3.
ALP H A ON E 6 Self Diagnosis and Troubleshooting Status Cause Water is too low during WASH/BIDET No water comes out during WASH/BIDET Solution 1. Low water pressure of the unit During use, turn the lever forward or backward to highest setting 2. Low water pressure of water supply If the water supply pressure is too low, contact your local water utility. 1. Water shut-off valve is turned off Turn on the water shut-off valve 2.
ALP HA ON E Warranty Your ALPHA ONE is warranted against defects in materials or workmanship for one (1) year from the date of original purchase. Defective parts or a defective product returned to ALPHA BIDET will be repaired with new or comparable rebuilt parts by ALPHA BIDET at their sole discretion. This limited warranty given by ALPHA BIDET covers all defects encountered in normal use of the ALPHA ONE, and does not apply in the following cases: 1.
ALP H A ON E 5. Any and all damages to plumbing, walls, floors, ceiling and personal properties resulting from water leaks or breakage. The product must be used at the user’s own risk. Therefore, the owner hereby releases the manufacturer and distributor from any and all claims for damages where the above condition exists.
