INSTRUCTION BOOK Model No. Product No Serial No.
Contents Page no Important to know ........................................................................................... 3 Operating .................................................................................................... 6 Ignition .................................................................................................... 8 Maintenance And Cleaning ............................................................................. 9 Mounting ..........................................
Important to know For safety's sake, turn pots and pans so that handles do not protrude, thus inviting accidents. Service and repair may only be performed by the distributor, or by a service organization approved by the distributor. Only repair parts delivered by the distributor may be used. Never place plastic or paper, etc., on the unit. If the unit should be switched on by accident, the paper could burn, plastic melt, etc. Please read the warranty. Avoid pinching the cable.
Product liability Distribution damages Our liability is limited to that which is stipulated by law, and covers only damage to persons and property, which results from defects in materials and workmanship of the unit itself. This liability extends for a period of 10 years from the date of purchase as a factory-new unit. Any damages due to transportation by us or by our representative must be reported to the dealer not later than one week after receipt of the unit.
Saftey To enable the consumer to locate any leaks in the installation, a smelling substance has been added to all gas qualities available in the market natural gas or bottled gas. When smelling gas or in case of any other kind of malfunction of the unit switch off the main gas supply or the bottled gas and contact service, an authorized heating and sanitary engineer or your gas supplier.
Operations Burner markings Signs at each operating knob indicate which burner is to be adjusted with the knob in question. Back Burner Front burner Panel markings Each operating knob has a ring showing the scale of markings. Burner 2 Off. Bruner 1 Max. flame Min.
Burner cover/burner ring Burner ring Together with the burner ring the burner cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Burner cover Correct Please note: It is consequently very important that the individual burner cover/ring is placed correctly on the burner. The burner ring has been provided with holes for the ignition electrode, and the thermo sensor.
Ignition 1. Depress and turn the control knob for the burner to the left to max. flame . (Ignition position) 2. The ignition electrode will emit sparks, and when the mixture of gas and air is correct, the burner will be ignited. If it is not possible to connect the unit to mains, a match may be used to ignite the burner. 3. After starting the burner, press the control knob for approx. 10 seconds to activate the automatic thermo-couple (thermo sensor ready). 5.
Maintenance and cleaning Stainless steel surfaces Perform daily cleaning with a slightly damp cloth. For more severe soiling, use a liquid scouring cream. Always clean the steel in the direction of the steel finish. To ensure that the steel retains its shine, it is recommended that you use a polishing agent for stainless steel on a regular basis. Always polish in the direction of the steel finish (cross-wise). Never use steel wool, metal sponges or other abrasive cleaning agents.
Mounting Caution: In order to avoid a hazard this appliance must be installed according to these instructions for installation The hob unit can be mounted in any type of kitchen with a table surface whose thickness is between 28 mm and 40 mm. Headroom The distance to any shelves or tops of a cabinet under the hob is to be at least 47 mm. Fixing Screw the fixing brackets out to such an extent that they can be turned in under the table top.
necessary to attach the reinforcement beam to the table surface, as it is held in place by a specially designed moulding, which is incorporated in the hob unit´s flanges.
Gas installation In accordance with local requirements for domestic gas cooking appliances. Gas installation must only be carried out by an authorised person. For gas types see technical data. Gas connection The gas intake is situated at the lower rear of the appliance. The intake has a ½" conical pipe thread (see fig 1) If the appliance is to be connected to a gas cylinder, conversion with the optional modification kit will be necessary. Pressure test The unit should be pressure-tested at Max. 150 mbar.
Technical data Type of gas Adjusted to natural gas: G20-20 mbar Category and pressures II2H3+ 20 mbar - 28/37 mbar Max. nominal gas consumption Natural gas 480 I/h Bottled gas 383 g/h Burner 2 Max. nominal load Q na HS: Medium sized burner = 2,0 kW x 1 Large sized burner = 3,0 kW x 1 Total= 5,0 kW Burner 1 FSD The unit features fully-secured gas taps (thermo-fuse).
Faults Question: Answer There is no spark when lighting the gas? Check whether the 230 V connection has been plugged in. The ground fault circuit relay way have switched off. The fuse has blown When the operating knob is released the gas ring goes out again? The operating knob has not been depressed long enough, or has not been depressed sufficiently. The gas ring burns very unevenly?? Check whether the cover has been replaced correctly, e.g. after cleaning.
If the gas-hob does not work Check to see whether a fuse has blown. Check to see whether the relay is switched off. by an alternative service organisation, approved by the distributor. Only spare parts delivered by the distributor may be used. Spare parts and service are the domain of our service network. If the problem is not with the fuse or relay, do not attempt to correct it yourself. Instead, contact our service network all repairs must be performed by our service personnel.
325 87-7169 Rev.
