Allworx® Server Software Release Notes (Release 6.9.7.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise without the prior written permission of Allworx. © 2009 Allworx Corp, a wholly owned subsidiary of PAETEC Holding Corp. All rights reserved. Allworx is a registered trademark of Allworx Corp. All other names may be trademarks or registered trademarks of their respective owners.
Server Software Release Notes – Release 6.9.7.1 Table of Contents Introduction ...........................................................................................................................................................2 Who Should Read This Document ...................................................................................................................2 Allworx System Software Compatibility...........................................................................................
Server Software Release Notes – Release 6.9.7.1 Introduction This document is an overview of the new features in Allworx® Server software 6.9.7.1, Allworx Phone firmware 1.9.6.1 (9224, 9212) and 1.9.5.7 (9102, 9202,9112), and Allworx Px 6/2 Expander firmware 1.9.5.
Server Software Release Notes – Release 6.9.7.1 Important Installation Information 1. This release should not be installed while the server is in Safe Mode. Installation should be done in Normal Mode using the Maintenance > Update screen. 2. Once the update has been activated and the server has finished rebooting, the server must be rebooted a second time. Use the Maintenance > Restart screen and choose the Normal restart option. 3. Downgrading to earlier releases causes problems and is not supported.
Server Software Release Notes – Release 6.9.7.1 In this procedure, you will set up a direct, one-to-one connection between a PC and the Px. You will boot the Px in Configuration Mode and manually configure its Boot Server IP Address. A. If the Px has already been powered on, disconnect power. B. If a cable is plugged into the Network port, disconnect it. C. Set up the PC’s network interface to obtain an IP address automatically (using DHCP). D. Apply power to the Px. E.
Server Software Release Notes – Release 6.9.7.1 Software Features Supported by Allworx Platform Software Features Call Assistant PC Application Support Allworx Communications Center (Group Calendaring) Total number of users supported FXO Ports FXS Ports FXO/FXS Support for G.
Server Software Release Notes – Release 6.9.7.1 New Features in Release 6.9.5/6/7 Allworx 9224 Phone, Tx 92/24 Expander Support The Allworx server software has full support for the Allworx 9224 Phone and Tx 92/24 Expanders. Support includes full plug-and-play installation, default key system and PBX templates, and the ability to configure up to 96 PFKs on one phone. Phone configuration enhancements include the ability to auto-assign all of the site’s phones to BLF PFKs with one click.
Server Software Release Notes – Release 6.9.7.1 Release 6.9.7.1 Changes Defect Number 4471 6x 10x 24x 9 9 9 4476 9 9 9 Resolution Increase the number of available BLF programmable function keys and parking orbits to accommodate the maximum number allowed on the Allworx 9224 Phone with three Tx 92/24 Telephone Expanders. Enable logging of Internal Event Codes in the System Events page of the Web Administrator.
Server Software Release Notes – Release 6.9.7.1 Known Issues Defect Number 4206 6x 10x 24x 9 9 9 9 4188 Problem Description When a user’s Presence is set from within the Admin tool, the wrong Presence is used. If a CO DID line definition is deleted. The FXO port cannot be used. 4185 9 9 9 The BLF PFK auto-assign button is disabled if no Outside Lines or only SIP trunks are defined on the system.
Server Software Release Notes – Release 6.9.7.1 3053 9 9 9 Park/Retrieve functionality fails when only G729a codec is used. 3014 9 9 9 Remote phones that are behind a firewall do not always hear ‘Music on Hold’. Workaround: Set the phone configuration to include the G711 codec. Workaround: Map the Remote phone’s RTP ports through the firewall. 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2009 Allworx Corp.
Server Software Release Notes – Release 6.9.7.1 Third Party Compatibility Issues Remote phones and port expanders behind Linksys® NAT devices stop functioning The Linksys BEFSR41 series NAT devices (and likely other models) have a bug where they can remap UDP ports on 20-minute boundaries. This can cause loss of audio during a call or the inability to place or receive calls. Multiple phones behind the same device will exhibit the problem much quicker than a single device. For best results, phone ports (e.
