Step-by-step Guide

ManualsBrandsAllterco Robotics ManualsElectronicsSmart switch

USER AND SAFETY GUIDE

SHELLY Plus i4

This document contains important technical and safety infor-

mation about the device, its safety use and installation.

⚠CAUTION! Before beginning the installation, please read this

guide and any other documents accompanying the device care-

fully and completely. Failure to follow the installation procedures

could lead to malfunction, danger to your health and life, viola-

tion of the law or refusal of legal and/or commercial guarantee

(if any). Allter

co Robotics is not responsible for any loss or dam-

age in case of incorrect installation or improper operation of this

vice due to failure of following the user and safety instructions

in this guide.

Product Introduction

Shelly® is a line of innovative Devices, which allow remote con-

trol of electric appliances through a mobile phone, tablet, PC, or

home automation system. Shelly® may work standalone on the

local Wi-Fi network, without being managed by a home auto-

mation controller, or it can also work through cloud home auto-

mation services. Shelly® devices can be accessed, controlled,

and monitored remotely from any place the User has Internet

connectivity, as long as the devices are connected to a Wi-Fi

router and the Internet.

Shelly® has an integrated web server, through which the User

may adjust, control and monitor the Device. Shelly® has two

Wi-Fi modes - access Point (AP) and Client mode (CM). To op-

erate in Client Mode, a Wi-Fi router must be located within the

range of the Device. Shelly® devices can communicate directly

with other Wi-Fi devices through HTTPS protocol. An API can be

provided by the Manufacturer.

Shelly® devices may be available for monitor and control even

if the User is outside the range of the local Wi-Fi network, as

long as the Wi-Fi router is connected to the Internet. The cloud

function could be used, which is activated through the web

server of the Device or through the settings in the Shelly Cloud

mobile application.

The User can register and access Shelly Cloud, using either An-

droid or iOS mobile applications, or any internet browser and

the website: https://my.Shelly.cloud/

Control your home with your voice

Shelly® devices are compatible with Amazon Echo and Google

Home supported functionalities. Please see our step-by-step

guide on: https://shelly.cloud/support/compatibility/

g. 1

SW4 SW3 SW1SW2 L L N

Legend

• N - Neutral input (Zero)

• L - Line input (110-240V)

• SW1 - Switch 1 (input)

• SW2 - Switch 2 (input)

• SW3 - Switch 3 (input)

• SW4 - Switch 4 (input)

Installation instructions

The Wi-Fi switch input Shelly Plus i4 may send commands for

control of other devices, over the Internet. It is intended to be

mounted into a standard in-wall console, behind power sockets

and light switches or other places with limited space. Shelly

may work as a standalone Device or as an accessory to another

home automation controller.

For more information, please visit:

http://shelly-api-docs.shelly.cloud/#shelly-family-overview or

⚠CAUTION! Danger of electrocution. The mounting/installa-

tion of the Device should be done by a qualied person (elec-

trician).

⚠CAUTION!Connect the Device only in the way shown in these

instructions. Any other method could cause damage and/or in-

jury.

⚠CAUTION!Use the Device only with a power grid and appli-

ances which comply with all applicable regulations. short circuit

in the powe

r grid or any appliance connected to the Device may

damage the Device.

⚠CAUTION!Тhe Device may be connected to and may control

electric circuits and appliances only if they comply with the re-

spective standards and safety norms.

⚠

CAUTION! The Device may be connected with solid sin-

gle-core cables with increased heat resistance to insulation not

less than PVC T105°C.

Before installing/mounting the Device ensure that the grid is

powered off (turned down breakers). Connect the Relay to the

power grid and install it in the console behind the switch/power

socket following the scheme that suites the desired purpose:

Connecting to the power grid with power supply 110-240V AC

(g. 1).

Before starting, wire check that the breakers are turned off and

there is no voltage on their terminals. This can be done with a

phase meter or multimeter. When you are sure that there is no

voltage, you can start wiring the cables according to g.1. Con-

nect with a wire the signal L to the common pin on the switch.

Install cables from the switch to the terminals SW1-SW4.

Connect a wire from the Fuse to “L”. Connect the Neutral to the

device.

Initial inclusion

You may choose if you want to use Shelly with the Shelly Cloud

mobile application and Shelly Cloud service. Instructions on

how to connect your device to the Cloud and control it through

the Shelly App can be found in the “App guide”. You can also

familiarize yourself with the instructions for Management and

Control through the embedded Web interface.

Specication

• Power supply: 110-240V, 50/60Hz AC

• Complies with EU standards: RED 2014/53/EU, LVD

2014/35/EU, EMC 2014/30/EU, RoHS2 2011/65/EU

• Working temperature: -20°C up to 40°C

• Radio signal power: 1mW

• Radio protocol: WiFi 802.11 b/g/n

• Frequency: 2412 - 2462 МHz

• Operational range (depending on local construction): up to

50 m outdoors, up to 30 m indoors •

• Dimensions: (HxWxL): 41x36x17 mm

• Electrical consumption: <1 W

• Mounting: Wall box

• Wi-Fi: YES

• Bluetooth: v4.2

• Basic/EDR: YES

• Bluetooth modulation: GFSK, π/4-DQPSK, 8-DPSK

• Multi-click support: Up to 32 possible actions (8 per button)

• Temperature protection: YES

• Scripting (mjs): YES

• MQTT: YES

• URL Actions: 20

• Scheduling: 50

• CPU: ESP32

• Flash: 4MB

Technical Information

• Control through Wi-Fi from a mobile phone, PC, automation

system or any other Device supporting HTTP and/or UDP pro-

tocol.

• Microprocessor management.

⚠CAUTION! Danger of electrocution. Mounting the Device to

the power grid has to be performed with caution.

⚠CAUTION! Do not allow children to play with the button/

switch connected the Device. Keep the Devices for remote con-

trol of Shelly (mobile phones, tablets, PCs) away from children

Declaration of conformity

Hereby, Allterco Robotics EOOD declares that the radio

equipment type Shelly Plus i4 is in compliance with Directive

2014/53/ EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full

text of the EU declaration of conformity is available at the fol-

lowing internet address

https://shelly.cloud/knowledge-base/devices/shelly-plus-i4/

Manufacturer: Allterco Robotics EOOD

Address: Bulgaria, Soa, 1407, 103 Cherni vrah Blvd.

Tel.: +359 2 988 7435

E-mail: support@shelly.cloud

Web: http://www.shelly.cloud

Changes in the contact data are published by the Manufacturer

at the ocial website of the Device http://www.shelly.cloud

All rights to trademark Shelly® and other intellectual rights

associated with this Device belong to Allterco Robotics EOOD.

Summary of content (2 pages)

PAGE 1
EN USER AND SAFETY GUIDE SHELLY Plus i4 This document contains important technical and safety information about the device, its safety use and installation. ⚠CAUTION! Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any).
PAGE 2
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.