Service manual

— 4 —
INITIAL BUS DATA SETUP (Cont.)
17. Select NO. 57 YGM6DCR4BSS2BSG (Y Gam / DC Res / B Strk Start / B Strk Gain) with ▲ or ▼ key. Adjust the data with
number keys for 84.
18. Select NO. 5B AF7CBP5 (Auto Flesh / C Band Pass) with ▲ or ▼ key. Adjust the data with number keys for A0.
19. Select NO. 62 IAS7STS6RAD (IF AGC / S Trap Switch / RF AGC) with ▲ or ▼ key. Adjust the data with number keys
for 65.
20 Select NO. 63 VIF5VL (VIF System Switch / Video Level) with ▲ or ▼ key. Adjust the data with number keys for 18.
21. Select NO. 67 VMD6VMG3SSN (VM Delay / VM Gain / Sync Sep Sens) with ▲ or ▼ key. Adjust the data with number
keys for 22.
22. Select NO. 69 EWD (E/W DC) with ▲ or ▼ key. Adjust the data with + or – key for 1C.
23. Select NO. 6A EWA (E/W Amp) with ▲ or ▼ key. Adjust the data with + or – key for 0F.
24. Select NO. 6B EWT (E/W Tilt) with ▲ or ▼ key. Adjust the data with + or – key for 30.
25. Select NO. 6C ECB4ECT (E/W Corner Btm / E/W Corner Top) with ▲ or ▼ key. Adjust the data with number keys for 72.
26. Select NO. 6D EWS7ETS3HSC (E/W Correction Switch / E/W Test / H Size Comp) with ▲ or ▼ key. Adjust the data with
number keys for 85.
27. Select NO. 83 OPT (Aspect Ratio / Surround) with ▲ or ▼ key. Adjust the data with + or – key for A0.
28. Select NO. 84 OP2 (Component / V Guide) with ▲ or ▼ key. Adjust the data with + or – key for 20.
29. Select NO. 88 CGR (RF Coring Gain) with ▲ or ▼ key. Adjust the data with + or – key for C0.
30. Select NO. 8A ROV (RF Overshoot Adjust) with ▲ or ▼ key. Adjust the data with + or – key for 04.
31. Select NO. 8B RPR (RF Preshoot Adjust) with ▲ or ▼ key. Adjust the data with + or – key for 20.
32. Select NO. 8D HR (H Display Position) with ▲ or ▼ key. Adjust the data with + or – key for 24.
33. Select NO. 8E SBO (Sub Bright Offset) with ▲ or ▼ key. Adjust the data with + or – key for 05.
34 Select NO. 92 DCL (YUV Color Difference) with ▲ or ▼ key. Adjust the data with + or – key for 01.
35. Select NO. 98 DRY (YUV R-Y Difference) with ▲ or ▼ key. Adjust the data with + or – key for 00.
36. Select NO. 9B ECN (16:9 Contrast Difference) with ▲ or ▼ key. Adjust the data with + or – key for E4.
37. Select NO. 9F EVS (16:9 V Size Difference) with ▲ or ▼ key. Adjust the data with + or – key for DC
38. Select NO. A1 EEA (16:9 E/W Amp Difference) with ▲ or ▼ key. Adjust the data with + or – key for FA.
39. Press the MENU key to turn off the Service Menu display.
SERVICE ADJUSTMENTS (Cont.)