Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Manual Version MTA1.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Our Full Product Range Page 1
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Safety Instructions Please keep the display away from any heat sources such as radiators or direct sunlight. Place the display in a stable and well‐ventilated place. Please handle with care as product contains glass. The holes or openings on the display are designed for ventilation. cover or block the ventilation holes or openings. Do not Remove protective covering from the screen before you use the display.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Quick Start Guide This section of the guide allows quick setup and use of the unit. Please refer to the main part of the User Guide for full information on use of the unit. Please follow the steps detailed below: 1. Unpack unit and place in desired location along with PC. 2. Connect the screen to the PC via the VGA Cable and link the screen’s Infrared touch sensors to the PC via the USB cable (as shown below).
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Contents: 1. 2. 3. Introduction ................................................................................................................................ 6 1.1 Box Contents ................................................................................................................... 6 1.2 Product Overview ............................................................................................................ 6 1.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Table of Figures Figure 1 Screen to PC Connections ...................................................................................................... 3 Figure 2 Product Overview................................................................................................................... 6 Figure 3 Serial Control Box to Screen Connection ...............................................................................
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 1. Introduction Congratulations on your purchase of our product. Please read carefully and follow all instructions in the manual before first use. The product should not be exposed to liquids dripping or splashing and no liquid filled objects, such as vases, should be placed on the product. For user convenience, a number of operations can be performed through the remote control. Attention: 1.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 1.3 Serial Control Box 1.3.1 Connection to the screen Before using the Remote Control the Serial Control Box (with the remote’s infrared sensor in it) must be connected to the screen. Figure 3 Serial Control Box to Screen Connection Unless Remote Control is faulty it is recommended that you do not attempt to change any settings with the Serial Control Box, only use it as a sensor for the main Remote Control.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 1.3.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 1.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 1.5 Replacing the Remote Control Battery 1. Open the battery cover 2. Take out the battery box in the right direction as shown in the picture below 3. Remove the used battery 4. Insert the new battery with its terminals corresponding to the indicator 5.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 1.6 Menu Operation The Menu includes the following sub‐menus: Picture, Sound, System, Function and Geometry. First connect the Serial Control Box to the screen via the CAT5 port (as shown). Figure 4 Serial Control Box to Screen Connection When using the Remote Control please ensure that it is no more than 20cm away from the sensor on the Serial Control Box.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Picture As with all settings these can be adjusted and changed back to default at any time. CONTRAST 50 BRIGHTNESS 50 COLOR TEMP or WARM/COOL/USER DEFINED or DYNAMIC/SOFT/USER DEFINED 120 50 500 50 1.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual System Here you can change all of the On Screen Display (OSD) settings such as menu brightness and how long it displays for. This sub‐menu also includes the fan settings so you can set what temperature the internal fan activates.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Geometry H‐POSTION V‐POSTION CLOCK PHASE Switching between inputs One crucial feature that does not appear on the Main Menu is selecting the input source. This is done by first pressing “MODE” and then scrolling down to the desired input source and select by pressing “→”. PC (VGA) HDMI DVI AV1 AV2 YPBPR 1.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 2. Set Up 2.1 Connecting to PC The touch screen must be connected to the PC in two ways: visually and interactively. The recommended visual connection is via the VGA Cable (included) meaning that the display acts like a monitor for the PC. The touch function is achieved by linking the Infrared touch sensors around the screen to the PC via the USB Cable (included).
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual PC (VGA) HDMI DVI AV1 AV2 YPBPR IMPORTANT: If the Touch Screen is the only monitor connected to your PC DO NOT take the following step. Only proceed with the following if you are using a laptop or another monitor is connected to your PC. Access the display options from your Control Panel or right‐click on your Desktop and choose “Properties” (then “Settings”) or “Screen resolution”.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 2.2 Installing the touch screen driver The touch screen driver can only be installed on a Windows Operating System, to utilize multi touch function it must be installed on to a PC that is running Windows 7. All Windows Operating Systems before Windows 7 can support the single touch function. There are separate drivers for Windows PCs, one for 32‐bit and one for 64‐bit.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual ETO, RS232 Series, Serial ‐ Single touch via Serial Port ETO,USB Series, USB ‐ Single touch via USB Port ETO, MT, Serial ‐ Multi touch via Serial Port ETO, MT, USB ‐ Multi touch via USB ETO, RS232, Serial ‐ Single touch via Serial Port If you require the multi touch function (ability to use two touch points on the display) then please select “ETO, MT, USB” as shown above.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Once installation is complete this box will appear: Page 19
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Click “Close”. IMPORTANT: Restart the computer. Once your PC starts back up, still using your mouse, access the “Pointer Device Settings” found in the bottom right‐hand corner of the taskbar (under the hidden icons section). From here you can access all of your touch screen settings, including a Help section for more details on the system.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Next you must calibrate your screen. Access the Pointer Device Services from the hidden icons and select Calibrate>UPDD>Calibrate. This will turn the screen white apart from a blue arrow; touch the screen on the point of the blue arrow. You will need to do this 4 times to allow the infrared sensors to calibrate.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual IMPORTANT: Restart the computer again. The screen should now be connected and fully operational. To make further changes or re‐calibrate the screen simply open Pointer Device Services at any time, it can be found in the bottom right‐hand corner of the taskbar (under the hidden icons section).
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 2.2.2 Changing your display to portrait mode IMPORTANT: If you require your content to display in portrait you must first calibrate your screen in landscape orientation before switching it to portrait orientation. Access the display options from your Control Panel or right‐click on your Desktop and choose “Properties” (then “Settings”) or “Screen resolution”.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Select the “Orientation” dropdown menu then click on “Portrait (flipped)”. Click “OK” and your screen contents and operations will now be rotated 90° clockwise. You may be asked “Do you want to keep these display settings?” click on “Keep changes”.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Page 25
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 3. F.A.Qs and Troubleshooting Guide 3.1 My Touch Screen is not displaying what is on my PC 3.1.1 Input Source Your Touch Screen may be sourcing its display from another input. First connect the Serial Control Box to the screen via the CAT5 port (marked REMOTE KEY BOARD on “Inputs” diagram Figure 5). When using the Remote Control please ensure that it is no more than 20cm away from the sensor on the Serial Control Box.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual is not being supplied with a video signal it will power OFF so ensure that video signal connection is connected properly. Also you must ensure that the Touch Screen is accessing the correct input. To do this you must first connect the Serial Control Box to the screen via the CAT5 port (marked REMOTE KEY BOARD on “Inputs” diagram Figure 2).
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 3.5 My Remote Control is not working If you have unpacked your unit, powered it ON and the Remote Control does not seem to be working please connect the Serial Control Box first. The Serial Control Box has the remote’s infrared sensor in it and must be connected to the screen when operating the Remote Control.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Figure 6 Serial Control Box to Screen Connection Unless Remote Control is faulty it is recommended that you do not attempt to change any settings with the Serial Control Box, only use it as a sensor for the main Remote Control. Once all required changes have been made the Serial Control Box can be disconnected. 3.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Click “Next”. When the next window appears you must highlight “Search for the best drivers in these locations.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Your PC will then search for the Touch Screen via the USB cable.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual Click “Finish.” Now you must calibrate your screen. To do this access the “Pointer Device Settings” found in the bottom right‐hand corner of the taskbar (under the hidden icons section). From here you can access all of your touch screen settings. Access the Pointer Device Services from the hidden icons and select Calibrate>UPDD>Calibrate. This will turn the screen white apart from a blue arrow; touch the screen on the point of the blue arrow.
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual IMPORTANT: Restart the computer again. The screen should now be connected and fully operational. To make further changes or re‐calibrate the screen simply open Pointer Device Services at any time, it can be found in the bottom right‐hand corner of the taskbar (under the hidden icons section).
Wall‐mounted Infrared Multi Touch Screen Display User’s Manual 4.