Warranty Guide

Series:
OLYMAPDT
Olympic Sleeve, Power Pin,
Yoke Stack Kettlebell &
Resistance Band Barbell
Adapter
INSTRUCTIONS
Determine the diameter of your bar then select the correct adapters
• For 1” Diameter Bars: Use part B (1” Steel Inner Adapters), and part G (1”
Outer Adapters) inside of part F (1.25” Outer Adapters)
• For 1.25”
Diameter Bars:
Use part C (1.25”
Inner Adapters),
and part F (1.25”
Outer Adapters)
• For 1.25” ALLN-1
Olympic
Resistance Bar:
Remove part C
(1.25” inner
adapters), use part
F (1.25” Outer
Adapters)
• For Bars that Required Custom Adapters: Use part C (Custom inner
adapter), and part F (Custom outer adapters)
• If your Bar Doesn’t Fit into any of the adapters you may require custom
adapters because your bar isn’t 1” or 1.25”. Contact us for custom adapters.
TrainChange Fitness
TrainChange.com
14 MONTH LIMITED WARRANTY
TrainChange Fitness warrants out our products to the original user against defective material or
workmanship for a period of 14 Month (except where noted on our product price schedule) from the
date of shipping. TrainChange Fitness reserves the right to determine whether the product failed
because of defective material, workmanship or other causes and to charge back for missing parts.
TrainChange Fitness at it’s discretion, will repair product covered under this warranty free of charge.
The distributor should direct the original user to return the product (with exceptions listed below) with the
distributor’s name, address, adequate proof purchase date or a copy of warranty card, and a short note
explaining the problem. Failures caused by accident, alteration, or misuse are not covered by this
warranty.
If one part of this product fails, please do not return the entire product. TrainChange Fitness will replace
free of charge component parts of thie product that fail within the first 14 months after purchase by the
original user. Items included in the category include by are not limited to adapters, eye bolts and other
components that make up this unit. Please contact the phone number below in order to obtain the
replacement component covered under warranty.
TrainChange Fitness or is authorized service representatives must perform all warranty repairs. Any
repair to the product by unauthorized server representatives voids this warranty. The rights under this
warranty are limited to the original user and may not be transferred to subsequent users.
This warranty is in lieu of all other warranties, expressed or implied, including warranties of
merchantability and fitness for a particular purpose. Some States do now allow the exclusion of
limitations of incident or consequential damages so the above limitation may not apply to you.
INTENDED USE OF THE PRODUCT
PLEASE DO NOT RETURN ANY PRODUCT
WITHOUT CALLING 1-888-858-7746
ASSEMBLY
1) Insert the Inner Adapter (Part B) (if required)
into the Sleeve (Part A). 2) Align both holes and
insert an Eye Bolt or Lock Bolt (Part E or D) 3)
Tighten the bolt through both holes, but leave
space so the bar can be inserted.
4) Insert your bar into the back of the Sleeve,
through the Inner Adapter. Push bar through,
toward the opposite end of the Sleeve, exposing enough room at the end of the bar so
the Outer Adapter can slide on.
5) Align the groove on part Outer Adapter (Part F) to
the notch inside of the Sleeve, then slide the Outer
Adapter onto your bar, and into the Sleeve.
The Outer Adapter should be at least 1” into the
Sleeve. Note: The longer your sleeve, the further
into the Outer Adapter should go, but no further than ¾ the length of the sleeve.
Slide bar back into sleeve, repeat on other Sleeve.
The product is designed to be used with a steel
bar, to hold weight plates and/or resistance
bands. The bar being used must be capable of
handling the amount of weight and resistance
placed on the sleeves. The sleeves DO NOT
increase the strength or maximum weight
capacity of the bar they are being used with. Do
not use this product outside of the designated
intent. Never modify the product for any other
purpose or use.
BEFORE USE
When unpacking, check the parts diagram
and part listing to make sure all of parts
are included. If any parts are missing or
damaged, please call your distributor.
PRODUCT INFORMATION
- Easily convert any bar into a barbell with this
product.
- Included (2) Sleeves, (2) 1”Steel Inner Adapter,
(2) 1.25” Inner Adapters, (2) 1” Outer Adapters,
(2) 1.25” Outer adapters, (2) Lock bolts and (2)
Eye bolts.
- Use with solid steel bars or steel tubing that is at
least 14 gauge or lower.