Specifications

ManualsBrandsAllied Telesyn International Corp ManualsComputer equipmentAT-VP504E FXS (SIP/MGCP)

Table Of Contents

MIB Structure (SIP/MGCP/NCS)

Reference Manual

VoIPTalk

Rev C

Summary of content (80 pages)

PAGE 1
MIB Structure (SIP/MGCP/NCS) VoIPTalk Reference Manual Rev C
PAGE 2
Copyright © 2001 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesyn International, Corp.
PAGE 3
Contents MIB Reference Manual Contents Chapter 1 MIB Structure ........................................................................................... 1 What is a MIB? ............................................................................................................ 1 Allied Telesyn MIB Structure ................................................................................................... 1 Storage Clauses ................................................................................
PAGE 4
Contents MIB Reference Manual apaUIServicesGroup ................................................................................................. 14 apaUIServicesPortnGroup..................................................................................................... 14 Chapter 5 gatewayGroup Parameters ................................................................... 17 gatewayGroup Basic Parameter................................................................................
PAGE 5
Contents MIB Reference Manual tftpServerStaticGroup ................................................................................................ 31 tftpServerDhcpGroup................................................................................................. 32 Chapter 10 apaByPassGroup Parameters .............................................................. 33 apaByPassGroup Parameters ...................................................................................
PAGE 6
Contents MIB Reference Manual Chapter 16 sntpGroup Parameters .......................................................................... 45 General Parameters .................................................................................................. 45 sntpStaticGroup Parameters ..................................................................................... 45 sntpDhcpGroup Parameters ......................................................................................
PAGE 7
Contents MIB Reference Manual sipUAServerStaticGroup ....................................................................................................... 61 sipUAServerDhcpGroup ........................................................................................................ 61 sipUAnGroup ............................................................................................................. 62 sipUAnAuthGroup................................................................................
PAGE 8
Contents VP500 Communication Unit MIB Reference Manual viii
PAGE 9
List of Tables MIB Reference Manual List of Tables Table 1 –––– Table 2 –––– Table 3 –––– Table 4 –––– Table 5 –––– Table 6 –––– Table 7 –––– Table 8 –––– Table 9 –––– Table 10 ––– Table 11 ––– Table 12 ––– Table 13 ––– Table 14 ––– Table 15 ––– Table 16 ––– Table 17 ––– Table 18 ––– Table 19 ––– Table 20 ––– Table 21 ––– Table 22 ––– Table 23 ––– Table 24 ––– Table 25 ––– Table 26 ––– Table 27 ––– Table 28 ––– Table 29 ––– Table 30 ––– Table 31 ––– Table 32 ––– Table 33 ––– Table 34 ––– Table 35 ––– Tabl
PAGE 10
List of Tables Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 Table 53 Table 54 Table 55 Table 56 Table 57 Table 58 Table 59 Table 60 Table 61 Table 62 Table 63 Table 64 Table 65 Table 66 Table 67 Table 68 Table 69 Table 70 Table 71 Table 72 Table 73 Table 74 Table 75 Table 76 MIB Reference Manual ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– ––– VP500 Bypass Grou
PAGE 11
1 MIB Structure This document lists and explains all parameters in the Allied Telesyn Management Information Base (MIB) structure. A description and possible values are provided to help you make the required changes to your system. Please read the comments very carefully before changing a parameter’s value. What is a MIB? A Management Information Base (MIB) specifies what variables the network elements maintain (the information that can be queried and set by the manager).
PAGE 12
Chapter 1 - MIB Structure MIB Reference Manual All parameters in the MIBs have been configured by default upon start up. However, if you need to modify some of these parameters (for example, parameters related to the country in which you are), use a SNMP browser. Note: The AT-VP504E FXO communication units can only run the SIP signaling protocol.
PAGE 13
Chapter 1 - MIB Structure MIB Reference Manual With the SIP signalling protocol: the VP500 communication unit uses the Provisioning MIB and SIP MIB. With the MGCP signalling protocol: the VP500 communication unit uses the Provisioning MIB and MGCP MIB. You can switch between protocols and the proper MIB will be activated upon restart. Note: If you are using AT-VP504E FXO communication units, switching protocol is not possible because these units can only run the SIP signaling protocol.
PAGE 14
Chapter 1 - MIB Structure MIB Reference Manual types: MIB Version • R/W: the parameter is “Read/Write” and can be edited. • R-O: the parameter is “Read-Only” and cannot be edited. Description: Short description of the parameter as displayed in the MIB. When possible, the default value for the parameter is provided. Dynamic: Describes the update status of the parameter, which can have three update types: • Dynamic (Yes): The parameter value is updated automatically.
PAGE 15
Part 1: Provisioning MIB
PAGE 16
PAGE 17
2 InterfaceGroup Parameters The Interface parameters allow you to set information pertaining to the IP addresses used by the VP500 communication unit. Basic Interface Parameters The basic interface parameters allow you to define the VP500 communication unit’s network “signature”. Table 4: IP Interface Parameters Name Access Description Dynamic interfaceQoSSignalingDSFiledValue R/W Signaling (SIP negociation) QoS Differentiated Services field value.
PAGE 18
Chapter 2 - InterfaceGroup Parameters interfaceDhcpGroup MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the VP500 communication unit. Table 6: Interface DHCP Parameters Name Access Description Dynamic interfaceDhcpPrimDnsIp R-O Primary DNS server IP address provided by the DHCP server. Default Value: 192.168.0.10 N/A interfaceDhcpSecDnsIp R-O Secondary DNS server IP address provided by the DHCP server. N/A Default Value: 192.168.0.
PAGE 19
Chapter 2 - InterfaceGroup Parameters MIB Reference Manual - Provisioning MIB Table 7: Interface QoS Parameters (Continued) Name Access interfaceQoSMediaIeee8021QUserPriority R/W Description IEEE 802.1Q VLAN user priority value for VoIP media packet. This value is used to set the user priority in the TCI field of the VLAN tag. Tagging user priority is applied only when the filter is enabled.
PAGE 20
Chapter 2 - InterfaceGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 10
PAGE 21
3 apaManager Parameters The apaManager Group parameters allow you to set information pertaining to the Unit Manager, which is a module of the IP Communication Server used to set and provision the VP500 communication units. apaManager Basic The following parameters allow you to define basic information about the Unit Manager the VP500 communication unit will use. Parameters Table 9: Unit Manager Parameters Name Access apaManagerEnable R/W Description Dynamic No Enable the Unit Manager.
PAGE 22
Chapter 3 - apaManager Parameters apaManagerDhcpGroup MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the Unit Manager. Table 11: Unit Manager DHCP Parameters Name Access Description Dynamic apaManagerDhcpVendorSpecificCode R/W DHCP Unit Manager vendor specific code. Default Value: 200 Yes apaManagerDhcpPrimHost R-O Unit Manager IP address or domain name provided by the DHCP server. Default Value: 192.168.0.
PAGE 23
4 apaUIGroup Parameters The apaUIGroup parameters allow you to set the various permission settings used when making calls and to set information pertaining to the telephony services. apaUIMapRuleGroup Parameters Note: The Provisioning MIB contains four (4) Dialing Map Rules. The parameter description is identical for each rule. For clarity’s sake, only one generic set of parameters is described in this manual.
PAGE 24
Chapter 4 - apaUIGroup Parameters MIB Reference Manual - Provisioning MIB Table 12: apaUIMapRulex Group Parameters (Continued) Name Access apaUIMapRulexPrefixDigit R/W Description Select the digits to prefix to the dialed number for Dial Map Rule #n. Dynamic Yes 0 = Prefix Area code 1 = Prefix Country code 2 = Prefix Country code and Area code Default Value: 2 apaUIServicesGroup Note: The following parameters only apply to access communication units such as the AT-VP504E FXS.
PAGE 25
Chapter 4 - apaUIGroup Parameters MIB Reference Manual - Provisioning MIB Table 13: Portn Call Forward Unconditional Parameters (Continued) Name Access apaUIServicesPortnCallForwardUnconditional DisableStarNumber R/W Description Digits to dial after the star key to disable the unconditional Call Forward.
PAGE 26
Chapter 4 - apaUIGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 16
PAGE 27
5 gatewayGroup Parameters The gatewayGroup parameters allow you to set the various permission settings used when making calls in gateway mode. Note: The gatewayGroup parameters are used only by gateway units such as the AT-VP504E FXO. gatewayGroup Basic Parameter The following parameter allows you to define the General Dial Prefix to use when making calls.
PAGE 28
Chapter 5 - gatewayGroup Parameters MIB Reference Manual - Provisioning MIB Table 17: Gateway Port n Parameters (Continued) Name Access gatewayPortnRedirectEnable R/W Description Enable the redirection of incoming calls on port #n used in FXO mode. Dynamic Yes 0 = Disable (IP dial tone) 1 = Enable (Redirected to address gatewayPortxRedirectToAddress) Default Value: 0 gatewayPortnRedirectToAddress gatewayPermLocalSameACGroup R/W Address to which incoming calls on port #n are redirected.
PAGE 29
Chapter 5 - gatewayGroup Parameters MIB Reference Manual - Provisioning MIB Table 19: Gateway Perm Local Diff AC Parameters (Continued) Name Access gatewayPermLocalDiffACAllowAll R/W Description Select which numbers are allowed to be called on port used in FXO mode.
PAGE 30
Chapter 5 - gatewayGroup Parameters MIB Reference Manual - Provisioning MIB Table 21: Gateway Perm Long Distance Different AC Parameters (Continued) Name Access Description Dynamic gatewayPermLongDistDiffACAllowed R/W Semi-colon separated list of numbers allowed to be called on port used in FXO mode (the destination call is long distance with a different area code than countryAreaCode).
PAGE 31
6 countryGroup Parameters The Country Group parameters allow you to set information pertaining to the physical location of the VP500 communication unit. Country Parameters The country parameters allow you to define information that will be used when dialing. Table 23: Country Group Parameters Name Access Description Dynamic countryCountryCode R/W Country code associated to the current location of the VP500 communication unit.
PAGE 32
Chapter 6 - countryGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 22
PAGE 33
7 portGroup Parameters The Port Group parameters allow you to set information pertaining to the four ports of the VP500 communication unit. General Parameters Note: Each port of the VP500 communication unit has its own set of parameters. The parameter description is identical for each port. For clarity’s sake, only one generic set of parameters is described in this manual.
PAGE 34
Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB Table 24: Port Parameters (Continued) Name Access Description Dynamic portSilenceDetectionTimeout R/W When silence is detected on the line, period of silent time after which the line is hanged up. 300 seconds = 5 minutes. Values range from 0 to 300 seconds. Default Value: 300 No portForcedEndOfCallEnable R/W Enable call interruption if unsuccessfull.
PAGE 35
Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB Table 26: DSP User Gain Parameters (Continued) Name Access portnDspUserGainOutputOffset R/W Description Port #n user output gain offset in dB. Default Value: -6 Dynamic No portnDspCountrySpecificGroup Table 27: DSP Country Specific Parameter Name Access portnDspCountrySpecificLoopCurrent R/W Description Port #n country specific loop current.
PAGE 36
Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB portnDspCodecG711aLawGroup Table 30: DSP Codec G711aLaw Parameters Name Access portnDspCodecG711aLawEnable R/W Description Enable G.711 a-Law (PCMA) on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDspCodecG711aLawPTimeMin R/W Port #n minimum packetization time (ptime) for PCMA in ms. Default Value: 20 Yes portnDspCodecG711aLawPTimeMax R/W Port #n maximum packetization time (ptime) for PCMA in ms.
PAGE 37
Chapter 7 - portGroup Parameters MIB Reference Manual - Provisioning MIB portnDspCodecG729ABGroup Table 33: DSP Codec G729AB Parameters Name portnDspCodecG729ABEnable Access R/W Description Enable G.729.AB on Port #n. Dynamic Yes 0 = Disable 1 = Enable Default Value: 1 portnDspCodecG729ABPTimeMin R/W Port #n minimum packetization time (ptime) for G.729.AB in ms. WARNING: Valid values are 10, 20, 30, and 40. The default value is used if the value is invalid.
PAGE 38
Chapter 7 - portGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 28
PAGE 39
8 syslogGroup Parameters The Syslog Group parameters allow you to set information pertaining to the Syslog daemon. syslogGroup Basic Parameters The following parameters allow you to set basic information pertaining to the Syslog daemon. Table 36: Syslog Parameters Name syslogMsgEnable Access R/W Description Enable the syslog daemon messages.
PAGE 40
Chapter 8 - syslogGroup Parameters syslogDhcpGroup MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the Syslog daemon. Table 38: Syslog DHCP Parameters Name Access Description Dynamic syslogDhcpVendorSpecificCode R/W DHCP Syslog server vendor specific code. Default Value: 110 Yes syslogDhcpHost R-O Syslog server IP address or domain name provided by the DHCP Server. Default Value: 192.168.0.
PAGE 41
9 tftpGroup Parameters The TFTP Group parameters allow you to set up the VP500 communication unit with the information pertaining to the server on which the software update is located. tftpGroup Basic Parameters The following parameters allow you to set basic information on the software update server. Table 39: tftp Group Parameters Name Access Description Dynamic tftpFileName R/W VP500 communication unit software file name to download from TFTP server. Default Value: apa.
PAGE 42
Chapter 9 - tftpGroup Parameters MIB Reference Manual - Provisioning MIB Table 40: tftp Server Static Group Parameters (Continued) Name Access Description Dynamic tftpServerStaticEmergencyHost R/W Static emergency TFTP server IP address or domain name. Default Value: 192.168.0.10 Yes tftpServerStaticEmergencyPort R/W Static emergency TFTP server IP port number. Default Value: 69 Yes tftpServerDhcpGroup The following parameters allow you to set DHCP information on the TFTP server.
PAGE 43
10 apaByPassGroup Parameters The APA Bypass Group is used to set information on the System Failure Bypass line connector, which is used as an emergency line in case of power or LAN failure. apaByPassGroup Parameters The following parameters are used to set up the behavior of the Bypass connector. Table 42: VP500 Bypass Group Parameters Name apaByPassModeAlwaysEnable Access R/W Description Always enable VP500 communication unit bypass mode.
PAGE 44
Chapter 10 - apaByPassGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 34
PAGE 45
11 apaSystemGroup Parameters The APA System Group parameters are used to report on the current status of the VP500 communication unit. apaSystemGroup Parameters The following parameters report in the current VP500 communication unit status. Table 43: APA System Group Parameters Name apaSystemOperationalStatusConfigFile Access R-O Description TFTP system operational configuration file download status.
PAGE 46
Chapter 11 - apaSystemGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 36
PAGE 47
12 apaCmdGroup Parameters The APA Command Group parameters are used to initiate tasks on the VP500 communication unit. apaCmdGroup Parameters The following tasks can be initiated. Table 44: APA Cmd Group Parameters Name apaCmdStartTelnetBenchTest Access R/W Description Instruct the VP500 communication unit to reboot in Telnet bench test mode. Dynamic Yes 0 = Off 1 = On Default Value: 0 apaCmdMode R/W Not implemented ... for future use only. Select the VP500 communication unit command mode.
PAGE 48
Chapter 12 - apaCmdGroup Parameters MIB Reference Manual - Provisioning MIB Table 44: APA Cmd Group Parameters (Continued) Name apaCmdCheckRam Access R/W Description Check the validity of the RAM. Dynamic Yes 0 = Off 1 = On Default Value: 0 apaCmdDownloadSoftware R/W Instruct the VP500 communication unit to download a file from TFTP server. Yes 0 = Off 1 = On Default Value: 0 apaCmdRestart R/W Instruct the VP500 communication unit to reboot.
PAGE 49
13 snmpGroup Parameters The SNMP Group parameters allow you to set information pertaining to the SNMP protocol. snmpGroup Parameters The following parameters allow you to define the SNMP settings of the VP500 communication unit. Table 45: SNMP Group Parameters Name Access Description Dynamic snmpAgentPort R/W SNMP Agent port number on which the unit must listen for SNMP requests. Default Value: 161 No snmpSystemDescription R/W A textual description of the entity.
PAGE 50
Chapter 13 - snmpGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 40
PAGE 51
14 apaInfoGroup Parameters The APA Info Group gives read-only information on all the various information used by the VP500 communication unit. apaInfoInterface Parameters The following parameters allow you to see information pertaining to the VP500 communication unit interface. Table 46: apaInfoInterface Parameters Name Access Description Dynamic apaInfoInterfacePrimDnsIpAddress R-O Primary DNS server IP address. Default Value: 192.168.0.
PAGE 52
Chapter 14 - apaInfoGroup Parameters MIB Reference Manual - Provisioning MIB apaInfoFileConfig- The following parameters allow you to see information pertaining to the VP500 communication unit’s configuration file. Group Table 48: apaInfo File Config Parameters Name Access Description Dynamic apaInfoFileConfigFileName R-O Configuration File name to download from the TFTP Server. Default Value: sip.
PAGE 53
15 configTrapGroup Parameters This chapter describes the traps messages that can be sent from the VP500 communication unit to the Unit Manager. Config Trap Parameters The Trap Info parameters give you information on the traps (messages) sent from the VP500 communication unit to the Unit Manager.
PAGE 54
Chapter 15 - configTrapGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 44
PAGE 55
16 sntpGroup Parameters This chapter describes the SNTP settings that can be set on the VP500 communication unit. General Parameters The general SNTP parameters allow you to enable and synchronize the SNTP feature. Table 50: SNTP General Parameters Name sntpEnable Access R/W Description Enable SNTP Client. Dynamic Yes 0 = Disable 1 = Enable Default Value: 0 sntpSynchronizationPeriod R/W Interval in minutes before sending a SNTP time request to the SNTP server. Values range from 2 to 1440 seconds.
PAGE 56
Chapter 16 - sntpGroup Parameters sntpDhcpGroup Parameters MIB Reference Manual - Provisioning MIB The following parameters allow you to set DHCP information for the VP500 communication unit Table 52: DHCP SNTP Parameters Name Access Description Dynamic sntpDhcpVendorCodeSpecific R/W DHCP SNTP server vendor specific code. Default Value: 208 Yes sntpDhcpHost R-O SNTP servers IP address or domain name provided by DHCP server. Default Value: 192.168.0.
PAGE 57
Chapter 16 - sntpGroup Parameters MIB Reference Manual - Provisioning MIB Table 53: SNTP Time Zone Parameters (Continued) Name sntpTimeZoneCustomTimeZoneIsValid Access R-O Description Validate custom time zone entered. Dynamic N/A 0 = Not valid. 1 = Valid.
PAGE 58
Chapter 16 - sntpGroup Parameters VP500 Communication Unit MIB Reference Manual - Provisioning MIB 48
PAGE 59
Part 2: MGCP MIB
PAGE 60
PAGE 61
17 mgcpConfiguration Parameters The MGCP Configuration parameters allow you to set information exclusive to VP500 communication units that run the Media Gateway Control Protocol (MGCP). Introduction The MGCP MIB is used with VP500 communication units that run the Media Gateway Control Protocol (MGCP). Table 54: MGCP MIB Version Parameter Name Access mgcpMibVersion R-O Description MIB version.
PAGE 62
Chapter 17 - mgcpConfiguration Parameters mgcpConfigurationEpIdGroup MIB Reference Manual - MGCP MIB The following parameters allow you to set information pertaining to endpoints. Table 56: End Point Id Parameters Name Access Description Dynamic mgcpConfigurationEpIdLocalNameTerm1 R/W String that specifies the term of the endpoint name. Default Value: aaln No mgcpConfigurationEpIdGatewayFqdnUseDns R/W Select the provenance of the Fully Qualified Domain Name (FQDN).
PAGE 63
Chapter 17 - mgcpConfiguration Parameters MIB Reference Manual - MGCP MIB mgcpConfigurationCallAgentDhcpGrou p Table 59: Call Agent DHCP Group Name Access Description Dynamic mgcpConfigurationCallAgentDhcpPrimary VendorSpecificCode R/W DHCP primary Call Agent vendor specific code. Default Value: 206 No mgcpConfigurationCallAgentDhcpPrimary Address R-O Primary Call Agent address provided by DHCP server. Can be a dotted IP string or a FQDN address. Default Value: 192.168.0.
PAGE 64
Chapter 17 - mgcpConfiguration Parameters MIB Reference Manual - MGCP MIB Table 60: Retransmission Parameters (Continued) Name Access mgcpConfigurationRetransmissionRsipInitial Delay R/W Description Delay in ms since the last RSIP to wait before sending the first RSIP for a new endpoint that wants to register. This is to avoid restart avalanche.
PAGE 65
Chapter 17 - mgcpConfiguration Parameters mgcpConfigurationLinePackageGroup MIB Reference Manual - MGCP MIB The following parameters allow you to set information pertaining to the line package. Table 63: Line Package Parameters Name Access Description Dynamic mgcpConfigurationLinePackageBzDuration R/W Busy tone timeout value in ms. Default Value: 30000 No mgcpConfigurationLinePackageDlDuration R/W Dial tone timeout value in ms.
PAGE 66
Chapter 17 - mgcpConfiguration Parameters MIB Reference Manual - MGCP MIB mgcpStatisticsThis chapter lists the various statistics information available for an Group Parameters VP500 communication unit that runs the Media Gateway Control Protocol (MGCP). Table 65: MGCP Statistics Parameters Name Access Description Dynamic mgcpStatisticsNumberOfActiveConnections R-O Number of active connections.
PAGE 67
Part 3: SIP MIB
PAGE 68
PAGE 69
18 sipUAGroup Parameters The sipUA Group parameters allow you to set information exclusive to VP500 communication units that run the Session Initiation Protocol (SIP). Introduction The SIP MIB is used with VP500 communication units that run the Session Initiation Protocol (SIP). Table 66: SIP MIB Version Parameter Name Access sipMibVersion R-O Description MIB version. Default Value: 1.
PAGE 70
Chapter 18 - sipUAGroup Parameters sipUALogGroup MIB Reference Manual - SIP MIB The following parameters allow you to set parameters pertaining to the SIP logging client. Table 68: sipUA Log Group Parameters Name Acccess sipUALogEnable R/W Description Dynamic Enable the SIP logging client (allow the stack to log SIP packets). Yes 0 = Disable 1 = Enable Default Value: 0 sipUALogUseDhcp R/W Select the provenance of the SIP logging client configuration.
PAGE 71
Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB sipUAServerGroup The following parameters allow you to set basic information pertaining to the SIP server configuration. Table 71: sipUA Server Group Parameters Name Acccess sipUAServerOutboundProxyEnable R/W Description Not implemented ... for future use only. Dynamic N/A 0 = Disable 1 = Enable Default Value: 0 sipUAServerUseDhcp R/W Select the provenance of the SIP server configuration.
PAGE 72
Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB Table 73: sipUA Log Group Parameters (Continued) Name Acccess Description Dynamic sipUAServerDhcpRegistrarHost R-O SIP registrar server IP address or domain name provided by the DHCP server. Default Value: 192.168.0.10 sipUAServerDhcpRegistrarPort R-O SIP registrar server IP port number provided by the DHCP server. N/A Default Value: 5060 sipUAServerDhcpProxyVendorSpecificCode R/W DHCP SIP proxy server vendor specific code.
PAGE 73
Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB Table 74: sipUAn Group Parameters (Continued) Name Acccess Description Dynamic sipUAnFriendlyName R/W Friendly name for SIP User Agent #n. Default Value: Port 1 Yes sipUAnOtherAliases R/W Semi-colon separated list of other aliases for SIP User Agent #n. An alias is either a user name or a telephone number. Default Value: Yes sipUAnMustUseSessionTimers R/W Select if the session timer must be used.
PAGE 74
Chapter 18 - sipUAGroup Parameters MIB Reference Manual - SIP MIB Table 76: sipUA AuthGroup Parameters (Continued) Name sipUAAuthValid VP500 Communication Unit Acccess R-O Description This value is set to: 1 = Value sipUAAuthUsrPwd is valid. 0 = Value sipUAAuthUsrPwd has a syntax error.
PAGE 75
A List of MIB Parameters A analogGatewayID .......................................................................................................... 4 apaByPassModeAlwaysEnable ................................................................................... 33 apaByPassModeLanFailEnable ................................................................................... 33 apaByPassModeServerFailEnable .............................................................................. 33 apaCmdCheckRam .....
PAGE 76
List of Parameters MIB Reference Manual apaUIServicesPortnCallForwardUnconditionalDisableStarNumber ............................. 15 apaUIServicesPortnCallForwardUnconditionalEnable ................................................. 14 apaUIServicesPortnCallForwardUnconditionalEnableStarNumber .............................. 14 C configTrapApaConfigInformation ................................................................................. 43 configTrapApaStatusConfigFile .................................
PAGE 77
List of Parameters MIB Reference Manual interfaceStaticSecDnsIp ................................................................................................ 7 interfaceStaticSubnetMaskIp ......................................................................................... 7 interfaceUseDhcp .......................................................................................................... 7 M mgcpConfigurationCallAgentDhcpPrimaryAddress .....................................................
PAGE 78
List of Parameters MIB Reference Manual portnConfigurationMode .............................................................................................. 23 portnDspAdaptativityJitterBuffer .................................................................................. 24 portnDspCodecG711aLawEnable ............................................................................... 26 portnDspCodecG711aLawPTimeMax .........................................................................
PAGE 79
List of Parameters MIB Reference Manual sipUAnOtherAliases..................................................................................................... 63 sipUAnPrefixCCAndAC ............................................................................................... 62 sipUAPort .................................................................................................................... 59 sipUAProtocoleVersion ............................................................................
PAGE 80
List of Parameters MIB Reference Manual T tftpBlockSize ................................................................................................................ 31 tftpDownloadStatus...................................................................................................... 31 tftpEmergencyFileName .............................................................................................. 31 tftpFileName .................................................................................