Summit 300-48 Switch Installation Guide Extreme Networks, Inc. 3585 Monroe Street Santa Clara, California 95051 (888) 257-3000 http://www.extremenetworks.com Published: September 2003 Part number: 123006-00 Rev.
©2003 Extreme Networks, Inc. All rights reserved. Extreme Networks, ExtremeWare, Alpine, and BlackDiamond are registered trademarks of Extreme Networks, Inc. in the United States and certain other jurisdictions.
Contents Preface Chapter 1 Chapter 2 Introduction 9 Conventions 10 Related Publications 10 Summit 300-48 Switch Overview Summary of Features Unified Access 11 11 Summit 300-48 Switch Front View Console Port 12 12 Summit 300-48 Switch LEDs 13 Summit 300-48 Switch Rear View Power Socket Serial Number MAC Address 14 14 14 15 Port Connections 15 Full-Duplex 15 Mini-GBIC Type and Hardware/Software Support Mini-GBIC Types and Specifications Long Range GBIC System Budgets 15 15 17 18 Site P
Contents Chapter 3 Appendix A Appendix B Operating Environment Requirements Rack Specifications and Recommendations 20 24 Evaluating and Meeting Cable Requirements Cabling Standards Cable Labeling and Record Keeping Installing Cable RJ-45 Connector Jackets Radio Frequency Interference Making Network Interface Cable Connections 26 26 26 26 28 29 30 Meeting Power Requirements Power Supply Requirements AC Power Cable Requirements Uninterruptable Power Supply Requirements 30 30 31 31 Applicable Indust
Figures 1 2 3 4 5 6 7 8 9 10 11 Summit 300-48 Switch Installation Guide Summit 300-48 switch front view Summit 300-48 switch rear view Total optical system budgets for long range GBICs Airflow through the Summit 300-48 chassis Properly secured rack Bend radius for fiber optic cable RJ-45 connector jacket types Fitting the mounting bracket Null-modem cable pin-outs PC-AT serial null-modem cable pin-outs Mini-GBIC modules 12 14 17 23 25 27 29 36 38 38 41 5
Figures 6 Summit 300-48 Switch Installation Guide
Tables 1 2 3 4 5 6 7 8 9 10 11 Summit 300-48 Switch Installation Guide Notice Icons Text Conventions Summit 300-48 Switch LED Behavior SX Mini-GBIC Specifications LX Mini-GBIC Specifications ZX mini-GBIC Specifications Minimum attenuation requirements AC Power Requirements Media Types and Maximum Distances AC Power Cable Requirements Console Connector Pinouts 10 10 13 16 16 17 18 22 28 31 38 7
Tables 8 Summit 300-48 Switch Installation Guide
Preface This preface provides an overview of this guide, describes guide conventions, and lists other publications that may be useful. Introduction This guide provides the required information to install the Summit™ 300-48 switch. This guide is intended for use by network administrators who are responsible for installing and setting up network equipment.
Preface Conventions Table 1 and Table 2 list conventions that are used throughout this guide. Table 1: Notice Icons Icon Notice Type Alerts you to... Note Important features or instructions. Caution Risk of personal injury, system damage, or loss of data. Warning Risk of severe personal injury. Table 2: Text Conventions Convention Description Screen displays This typeface indicates command syntax, or represents information as it appears on the screen.
1 Summit 300-48 Switch Overview This chapter describes the features and functionality of the Summit 300-48 switch.
Summit 300-48 Switch Overview Summit 300-48 Switch Front View Figure 1 shows the Summit 300-48 switch front view. Figure 1: Summit 300-48 switch front view 10/100/1000 Mbps ports Expansion module slot Mini-GBIC ports Console port 10/100 Mbps ports with PoE LB48001 The Summit 300-48 switch has 48 autosensing 10/100 Ethernet ports using RJ-45 connectors and provides four unpopulated Extreme mini-GBIC ports.
Summit 300-48 Switch LEDs Summit 300-48 Switch LEDs Table 3 describes the light emitting diode (LED) behavior on the Summit 300-48 switch. Table 3: Summit 300-48 Switch LED Behavior Unit Status LED (MGMT LED) Color Indicates Blinking Green The Summit switch is operating normally. Solid Amber The Summit has failed its POST. Off No power. Power Supply Status LEDs (per power supply) Color Indicates Solid Green The power supply is operating normally. Solid Amber There is a fault.
Summit 300-48 Switch Overview Table 3: Summit 300-48 Switch LED Behavior (continued) 10/100/1000 Mbps Port Status LEDs Color Indicates Green solid Link is present; port is enabled; full-duplex operation. Green blinking Link is present; there is activity. Amber blinking Reserved. Off Link is not present or the port is disabled. Mini-GBIC Port Status LEDs Color Indicates Yellow blinking A non-supported GBIC is installed on this port.
Port Connections MAC Address This label shows the unique Ethernet MAC address assigned to this device. NOTE The Summit 300-48 switch certification and safety label, and the serial number and MAC address labels are located on the bottom of the switch. Port Connections The Summit 300-48 switch uses a combination of 10BASE-T/100BASE-TX ports using RJ-45 connectors and Small Form Factor Plugable (SFP) Gigabit Interface Connectors (GBICs), also known as mini-GBICs.
Summit 300-48 Switch Overview Table 4 describes the specifications for the SX mini-GBIC interface. Table 4: SX Mini-GBIC Specifications Parameter Minimum Typical Maximum Transceiver Optical output power -9.5 dBm Center wavelength 830 nm -4 dBm 850 nm 860 nm Receiver Optical input power sensitivity -21 dBm Optical input power maximum Operating wavelength -4 dBm 830 nm 860 nm General Total system budget 11.5 dBm Total optical system budget for the SX mini-GBIC is 11.5 dBm.
Mini-GBIC Type and Hardware/Software Support Table 6 describes the specifications for the ZX mini-GBIC interface.
Summit 300-48 Switch Overview Table 7 lists the minimum attenuations that are required by each long range GBIC to prevent saturation of the receiver.
2 Site Preparation This chapter describes how to prepare your site for installing Extreme Networks equipment. It contains information on environmental and cabling requirements, power requirements, and building and electrical code organizations.
Site Preparation Planning Your Site To install your equipment successfully, you should plan your site carefully.
Meeting Site Requirements Building and Electrical Codes Building and electrical codes vary depending on your location. Comply with all code specifications when planning your site and installing cable. The following sections are provided as a resource to obtain additional information. Three major building codes are: • Uniform Building Code—produced by the International Conference of Building Officials (ICBO); 5360 South Workman Mill Road; Whittier, California 90601 USA. www.icbo.
Site Preparation Wiring Closet Considerations You should consider the following recommendations for your wiring closet: • Ensure that your system is easily accessible for installation and service. See “Rack Specifications and Recommendations” on page 24 for specific recommendations. • Use appropriate AC power for your switch, as described in Table 8. Table 8: AC Power Requirements Switch Type Country Requirements Summit North America 13 A service receptacle, NEMA 5-15 for 110/220 VAC power supplies.
Meeting Site Requirements • Maintain ambient operating temperature: 32° to 104° F (0° to 40° C). • Maintain storage Temperature: -40° to 158° F (-40° to 70° C). NOTE Like all electrical equipment, product lifetimes degrade with increased temperature. If possible, temperatures should be kept at approximately 78° F (25° C) or lower. Airflow Requirements.
Site Preparation • Connect conductors (metals, etc.) to ground, using dedicated grounding lines. • Use electrostatically safe equipment and the ESD straps. Rack Specifications and Recommendations Racks should conform to conventional standards. In the United States, use EIA Standard RS-310C: Racks, Panels, and Associated Equipment. In countries other than the United States, use IEC Standard 297.
Meeting Site Requirements Space Requirements for the Rack Provide enough space in front of and behind the switch so that you can service it easily. Allow a minimum of 48 inches (122 cm) in front of the rack and 24 inches (61 cm) behind the rack. When using a relay rack, provide a minimum of 24 inches (61 cm) of space behind the mounted equipment. Extra room on each side is optional. NOTE Install your equipment rack near an easily accessible power outlet.
Site Preparation Evaluating and Meeting Cable Requirements This section addresses requirements for the that cable you should use when installing your network equipment.
Evaluating and Meeting Cable Requirements • Use cable managers to route cable bundles to the left and right of the network equipment to maximize accessibility to the connectors. • Provide enough slack—approximately 2 to 3 inches (5.08-7.62 cm)— to provide proper strain relief. • Bundle cable using velcro straps to avoid injuring cables. • If you build your own cable, ensure that cable is properly crimped. • When installing a patch panel using twisted pair wiring, untwist no more than 1 inch (2.
Site Preparation Cable Distances Table 9 shows cable media types and maximum distances that support reliable transmission in accordance with international standards except where noted. Table 9: Media Types and Maximum Distances Standard Media Type Mhz•Km Rating Maximum Distance (Meters) 1000BASE-SX (850 nm optical window) 50/125 µm multimode fiber 400 500 50/125 µm multimode fiber 500 550 62.5/125 µm multimode fiber 160 220 62.
Evaluating and Meeting Cable Requirements Figure 7 shows examples of connector jacket types that are not recommended as well as those that are recommended. Figure 7: RJ-45 connector jacket types Not recommended Best Better 0.1" = 1mm actual 39.37% : 254% SPG_001 Radio Frequency Interference If you use unshielded twisted pair (UTP) cabling in an installation, take precautions to avoid radio frequency (RF) interference.
Site Preparation Making Network Interface Cable Connections Use the appropriate type of cable to connect the ports of your switch to another switch or router. Working carefully, one port at a time, follow these steps: 1 Verify that you have identified the correct cable for the port. 2 Use an alcohol wipe or other appropriate cleaning agent to clean the cable connectors; make sure they are free of dust, oil, and other contaminants.
Meeting Power Requirements AC Power Cable Requirements Use an AC power cable appropriate for your country. Check your local electrical codes and regulatory agencies for power cable requirements. The countries listed in Table 10 have the following additional requirements: Table 10: AC Power Cable Requirements Country Requirements USA and Canada • The cable set must be UL-approved and CSA-certified. • The minimum specification for the flexible cable is No. 18 AWG (1.
Site Preparation • Provide power for some time after a blackout has occurred. In addition, some UPS or UPS plus software combinations provide the following functions: • Automatic shutdown of equipment during long power outages. • Monitoring and logging of power supply status. • Display the voltage (current draw) of the equipment. • Restart equipment after a long power outage. • Display the voltage currently on the line. • Provide alarms on certain error conditions. • Provide short circuit protection.
Applicable Industry Standards Applicable Industry Standards For more information, see the following ANSI/TIA/EIA standards: • ANSI/TIA/EIA-568-A—discusses the six subsystems of a structured cabling system. • ANSI/TIA/EIA-569-A—discusses design considerations. • ANSI/TIA/EIA-606—discusses cabling system administration. • ANSI/TIA/EIA-607—discusses commercial building grounding and bonding requirements. You can access these standards at http://www.ansi.org/ or http://www.tiaonline.org/.
Site Preparation 34 Summit 300-48 Switch Installation Guide
3 Switch Installation This chapter describes the following topics: • Determining the Switch Location on page 35 • Installing the Switch on page 36 • Connecting Equipment to the Console Port on page 37 • Powering On the Switch on page 39 • Checking the Installation on page 39 • Logging In for the First Time on page 39 • Installing or Replacing a Mini-Gigabit Interface Connector (Mini-GBIC) on page 40 CAUTION Use of controls or adjustments of performance or procedures other than those specified herein can r
Switch Installation Following Safety Information Before installing or removing any components of the switch, or before carrying out any maintenance procedures, read the safety information provided in Appendix A of this guide. Installing the Switch The Summit 300-48 switch can be mounted in a rack, or placed free-standing on a tabletop. Rack Mounting CAUTION Do not use the rack mount kits to suspend the switch from under a table or desk, or to attach the switch to a wall.
Connecting Equipment to the Console Port 5 Repeat steps 2 - 4 for the other side of the switch. 6 Insert the switch into the 19-inch rack. Take care to load the rack so that it is not top-heavy. Do not cover vents that would restrict airflow. 7 Secure the switch with suitable screws (not provided). 8 Connect the switch to the redundant power supply (if applicable). 9 Connect cables. Free-Standing The Summit 300-48 switch is supplied with four self-adhesive rubber pads.
Switch Installation Appropriate cables are available from your local supplier. To make your own cables, pinouts for a DB-9 male console connector are described in Table 11.
Powering On the Switch Powering On the Switch Connect the AC power cable to the switch and then to the wall outlet. Turn the on/off switch on the back of the Summit 300-48 switch to the on position. Checking the Installation After turning on power to the Summit 300-48 switch, the device performs a Power On Self-Test (POST). During the POST, all ports are temporarily disabled, the port LED is off, and the MGMT LED flashes. The MGMT LED flashes until the switch successfully passes the POST.
Switch Installation 5 Assign an IP address and subnetwork mask for VLAN default by typing config vlan default ipaddress 123.45.67.8 255.255.255.0 Your changes take effect immediately. 6 Save your configuration changes so that they will be in effect after the next switch reboot, by typing save. NOTE For more information on saving configuration changes, see the Summit 300-48 Software User Guide.
Installing or Replacing a Mini-Gigabit Interface Connector (Mini-GBIC) • Do not stretch the fiber. • Make sure the bend radius of the fiber is not less than 2 inches. In addition to the previously described tasks, Extreme Networks recommends the following when installing or replacing mini-GBICs on an active network: • Use the same type of mini-GBIC at each end of the link. • Connect one end of the link to the Tx port.
Switch Installation To remove the mini-GBIC connector labeled “Module A,” gently squeeze the sides to release it, and pull the mini-GBIC out of the slot. To remove the mini-GBIC connector labeled “Module B,” lift down on the front handle and pull the mini-GBIC out of the slot. To insert a mini-GBIC connector: 1 Holding the mini-GBIC by its sides, insert the mini-GBIC into the port on the switch. Mini-GBICs can be installed in ports 25 and 26 on the Summit 300-48 switch.
A Safety Information WARNING! Read the following safety information thoroughly before installing your Extreme Networks switch. Failure to follow this safety information can lead to personal injury or damage to the equipment. Installation, maintenance, removal of parts, and removal of the unit and components must be done by qualified service personnel only.
Safety Information • The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN60320/IEC320 appliance inlet. • France and Peru only This unit cannot be powered from IT† supplies. If your supplies are of IT type, this unit must be powered by 230 V (2P+T) via an isolation transformer ratio 1:1, with the secondary connection point labeled Neutral, connected directly to ground.
Lithium Battery Lithium Battery The lithium battery is not user-replaceable. WARNING! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. • Disposal requirements vary by country and by state. • Lithium batteries are not listed by the Environmental Protection Agency (EPA) as a hazardous waste. Therefore, they can typically be disposed of as normal waste.
Safety Information 46 Summit 300-48 Switch Installation Guide
B Technical Specifications Physical Dimensions Summit 300-48 Height: 3.5 inches (8.89 cm) Width: 17.25 inches (43.815 cm) Depth: 18.25 inches (46.355 cm) Weight (with one power supply unit): 14 lbs (6.35kg) Safety Agency Certifications UL60950 3rd Edition, Listed Device CSA 22.
Technical Specifications Electromagnetic Compatibility FCC CFR 47 part 15 Class A ICES-003 Class A European EMC standards for ITE • EN 55022:1998 Class A • EN 55024:1998 Class A includes IEC 61000-4-2, 3, 4, 5, 6, 8, 11 • EN 61000-3-2,3 (Harmonics & Flicker) • ETSI EN 300 386:2001 (EMC Telecommunications) • 89/336/EEC EMC Directive International EMC Certifications Heat Dissipation • ISPR 22:1997 Class A • CISPR 24:1997 Class A • VCCI Class A (Japan) • AS/NZS 3548 (Australia) • CNS 134
ACN 090 029 066 C-Tick (Australian Communication Authority) Underwriters Laboratories (USA and Canada) MIC (South Korea) BSMI, Republic of Taiwan NOM (Mexican Official Normalization, Electronic Certification and Normalization) Summit 300-48 Switch Installation Guide 49
Technical Specifications 50 Summit 300-48 Switch Installation Guide
Index A airflow requirements amperage, calculating ANSI standards 23 32 33 27 C cable identification records cable labeling identification records cable manager cable requirements bend radius fiber optic UTP meeting cable types and distances cabling standards ANSI BISCI certification marks commercial building standards console port connecting equipment to conventions notice icons, About This Guide text, About This Guide 26 26 26 27 27 26 28 48 37 10 10 47 24 24 25 25 25 Summit 300-48 Switch Install
media types and distances mini-GBIC specifications LX SX 28 16 16 O operating environment requirements building codes electrical codes wiring closet optical-fiber cable connections 21 22 30 P plenum-rated cable port connections power cable, replacing power requirements dual power supplies power cable power supply power supply specifications powering on the switch power-off specifications 27 15 31 31 31 48 39 48 R rack mounting the switch rack specifications grounding mechanical recommendations mountin
