Rapier Series Switch Hardware Reference Rapier 16fi Rapier 24i Rapier 48i Rapier 48w
Rapier Series Switch Hardware Reference Document Number C613-03020-00 REV K © 1999-2007 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis, Inc. reserves the right to change specifications and other information in this document without prior written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc.
Hardware Reference 3 Contents Models Covered by this Document .................................................................... 4 Why You Should Read this Document ............................................................... 4 Hardware Overview .......................................................................................... 5 Rapier Switch Models ................................................................................. 8 Rapier G6 ...................................................
Rapier Series Switch Models Covered by this Document This Hardware Reference includes information on the following models: ■ Rapier G6 6-port 100BASE-TX/1000BASE-T (RJ-45 connectors) ■ Rapier G6F-LX/SC 6-port 1000BASE-LX (SC fibre connectors) ■ Rapier G6F-SX/SC 6-port 1000BASE-SX (SC fibre connectors) ■ Rapier G6F-SX/MT-RJ 6-port 1000BASE-SX (MT-RJ fibre connectors) ■ Rapier 8/8MT 8-port 10BASE-T/100BASE-TX (RJ-45 connectors) plus 8-port 100BASE-FX (MT-RJ fibre connectors) ■ Rapier 8/8SC 8-po
Hardware Reference 5 Hardware Overview This section provides an overview of the hardware features of Rapier Series Switches. Hardware descriptions for Uplink Modules, NSMs, and PICs can be found in their respective hardware references. These references can be found on the CD-ROM bundled with your switch, or can be downloaded from www.alliedtelesis.com/support/software.
Rapier Series Switch Regulatory Standards All models except Rapier 48w ■ EMC: CISPR22 class A, FCC class A, and VCCI class A ■ Immunity: EN50082 levels 2 (ESD), 3 (susceptibility), 4 (fast transients), 5 (power surge), and 6 (RF immunity) ■ Safety: UL1950, CSA22.2, EN60950 Rapier 48w LEDs NEBS Power Supply Unit ■ EMC: EN55022 class A, and FCC class A ■ Safety: UL60950-1, CAN/CSA22.2 No.
Hardware Reference 7 Rapier G6, G6F/LX, G6F/SX, G6F/MT Processing Core ■ Gigabit ASIC switch chip ■ Non-blocking L2 and L3 IP Switching All models except Rapier 48w ■ 200MHz RISC processor (250 MHz for Rapier 24i models with revision N or higher PCBs) ■ 32MBytes Synchronous DRAM ■ 6MBytes flash memory (16MBytes for Rapier i models) ■ 128KBytes Non-volatile Storage (battery backed SRAM) Rapier 48w Asynchronous Serial Port ■ 350MHz processor ■ 64MBytes Synchronous DRAM ■ 32MBytes flash
Rapier Series Switch Rapier Switch Models This section provides hardware descriptions for individual switch models.
Hardware Reference 9 Rapier G6F-SX/SC (Figure 3) ■ 6-port 1000BASE-SX (SC fibre connectors) ■ Two 10/100/1000BASE uplink bays ■ Layer 3 Managed Switch Figure 3: Front panel of the Rapier G6F/SX Rapier G6F-SX/MT-RJ (Figure 4) ■ 6-port 1000BASE-SX (MT-RJ fibre connectors) ■ Two 10/100/1000BASE uplink bays ■ Layer 3 Managed Switch Figure 4: Front panel of the Rapier G6F/MT Rapier G6f Layer 3 Gigabit Ethernet Switch 7 RS-232 TERMINAL PORT PORT ACTIVITY 1000BASE-SX / MT-RJ ASYN0 1 L/A 2 L/
Rapier Series Switch Rapier 8/8SC (Figure 6) ■ 8-port 10BASE-T/100BASE-TX (RJ-45 connectors) ■ 8-port 100BASE-FX (SC fibre connectors) ■ Two 1000BASE uplink bays ■ One Network Service Module bay, with support for various WAN interface cards ■ One PCI Accelerator Card (PAC) Slot ■ Layer 3 Managed Switch Figure 6: Front panel of the Rapier 8/8SC 1 2 3 L /A 4 L /A 5 L /A 6 L /A 7 L /A Rapier 8/8 8 L /A L /A L /A 17 PORT ACTIVITY L /A D/C D/C D/C D/C D/C D/C D/C D/C 9
Hardware Reference 11 Figure 8: Front panel of the Rapier16Fi-FX/MT.
Rapier Series Switch Rapier 24 (Figure 11) ■ 24-port 10BASE-T/100BASE-TX (RJ-45 connectors) ■ Two 1000BASE uplink bays ■ One Network Service Module bay, with support for various WAN interface cards ■ One PCI Accelerator Card (PAC) Slot ■ Auto-negotiating Layer 3 Managed Switch Figure 11: Front and rear panels of the Rapier 24 (AC model) Front panel Layer 3 Fast Ethernet Switch 25 10BASE-T / 100BASE-TX 1X 3X 5X 7X 9X 11X 13X PORT ACTIVITY 15X 17X 19X 21X 23X L /A 100M LINK / D
Hardware Reference 13 Rapier 24i (Figure 12) ■ 24-port 10BASE-T/100BASE-TX (RJ-45 connectors) ■ Two 10/100/1000BASE uplink bays ■ One Network Service Module bay, with support for various WAN interface cards) ■ One PCI Accelerator Card (PAC) Slot ■ Auto-negotiating Layer 3 Managed Switch ■ Enhanced switching core Figure 12: Front panel of the Rapier 24i.
Rapier Series Switch Figure 14: Front panel of the Rapier 48i.
Hardware Reference 15 AT-TFTP Server This section explains how to access and use the AT-TFTP Server. You can transfer configuration files as well as download software upgrades with AT-TFTP Server. 1. If AT-TFTP Server has not been installed, install it from the Documentation and Tools CD-ROM shipped with your switch. You can also download it from www.alliedtelesis.com/support/software/. Select AT-TFTP Server from the Start > Programs > Allied Telesis > AT-TFTP Server menu. 2.
Rapier Series Switch 3. • Check “Diagnostics Messages” to display additional diagnostic messages in the AT-TFTP window when debugging file transfers. • Choose whether AT-TFTP Server should respond to TFTP requests received via IPv4 only, IPv6 only, or both IPv4 and IPv6. • Click the OK button when you finish.
Hardware Reference 17 Switch Startup This section outlines the log in and start-up procedures for your switch. Although the switch will perform basic switching operations without being configured, you will need to go through these log in and start-up procedures if you wish to configure the switch and access its full layer 3 switching capabilities. To Log In Using the supplied RS-232 DB9 straight-through cable, connect your terminal or PC to the RS-232 Terminal Port on the switch’s front panel.
Rapier Series Switch To access help files To display a list of help topics, enter: help To display help on a specific topic, enter: help topic Alternatively, type a question mark (?) at the end of a partially completed command to see a list of valid options. Startup Procedures When the switch starts up following either a power cycle or an operatorinitiated reboot (using the Reset button or RESTART command), a series of start-up messages is sent to the RS-232 Terminal Port (Figure 17).
Hardware Reference 19 During the start-up process the switch will generate four different types of messages. All messages are preceded by one of the words INFO, PASS, FAIL, or ERROR. The significance of these words is shown in Table 2. Table 2: Switch start-up message classes Message Meaning INFO An action will be taken by the system. PASS A test has been completed successfully. ERROR An error message that a test has failed, but the system will continue to operate.
Rapier Series Switch INFO: Self tests complete. The start-up tests have finished. INFO: Downloading switch software. The process of downloading the switch software and vector table from ROM is about to begin. ERROR: Code load retried. FAIL: Code load failed. The load of the code from ROM to RAM failed. The load is retried a number of times. Each time a failure occurs, the ERROR message is displayed. If the maximum number of attempts is reached, the FAIL message is displayed.
Hardware Reference 21 Switch Interfaces This section provides pin assignments for the asynchronous console ports, RJ-45 switch ports, and the Redundant Power Supply (RPS) connector. If you have installed a Port Interface Card (PIC), pin assignments for these can be found in the Port Interface Card Hardware Reference (which is included on the Documentation and Tools CD-ROM bundled with your switch, or can be downloaded from www.alliedtelesis.com/support/software).
Rapier Series Switch NEBS Compatibility The management/asyn intra-building ports of the Rapier 48w are suitable for connection to intra-building or unexposed wiring or cabling only. The management/asyn intra-building ports of the Rapier 48w must not be metallically connected to interfaces that connect to the OSP or its wiring.
Hardware Reference 23 If a twisted pair cable is to join two ports and only one of the ports has an internal crossover, the two pairs must be straight through, as listed in Table 5. Table 5: RJ-45 Pin assignments, straight through cable End 1 End 2 1 (TX+) 1 (TX+) 2 (TX-) 2 (TX-) 3 (RX+) 3 (RX+) 6 (RX-) 6 (RX-) If a twisted pair cable is used to join two ports and either both ports are labelled with an “X” or neither port is labelled with an “X”, a crossover must be included in the wiring.
Rapier Series Switch Redundant Power Supply AC models of Rapier Switches have a Redundant Power Supply (RPS) connector on their rear panel. Table 8 lists the connector’s pin numbers and pin functions. Table 8: RPS Connector Pin Numbers and Functions Pin Number Function 1 +12 VDC 2 Remote Sense (RS) +5 VDC 3 Remote Sense (RS) Ground 4 Remote Sense (RS) +3.3 VDC 5 Redundant Power Supply (RPS) Present 6 Ground (+3.
Hardware Reference 25 Fans and Filters on the Rapier 48w The Rapier 48w has two fan-only modules (FOMs) located on the front. Each FOM contains an air filter which should be changed periodically. The efficiency period of the air filter will depend on the air quality in which the switch is operated, but for a normal office environment, we recommend replacing the air filters every 3 months. The following procedures describe how to replace FOMs and air filters.
Rapier Series Switch . 3. Install filters in the replacement fan-only module. Install an air filter in the replacement FOM. Insert the air filter into the narrow slot between the faceplate of the FOM and the fan. Position the air filter with the plastic frame towards the fan, the quadrafoam towards the faceplate, and the flextab to the top. The air filter should fit snugly.
Hardware Reference 27 4. Install the replacement fan-only module. Keep the FOM in straight alignment and insert it slowly. Forcing a misaligned FOM is likely to damage both the chassis and FOM. Slowly and carefully slide the replacement FOM into the cage, making sure that the air filter and the flextab are clear of any contact points. Firmly press the FOM until the faceplate engages, or nearly engages, the chassis. 5. Secure the fan-only module.
Rapier Series Switch 3. Install the replacement air filter in the fan-only module. Insert the air filter into the narrow slot between the faceplate of the FOM and the fan. Position the air filter with the plastic frame towards the fan, the quadrafoam towards the faceplate, and the flextab to the top. The air filter should fit snugly. 4. Re-install the fan-only module. Keep the FOM in straight alignment and insert it slowly. Forcing a misaligned FOM is likely to damage both the chassis and FOM.
Hardware Reference 29 Switch Cables and Loopback Plugs This section describes how to make cables for connecting the switch’s interfaces to networks, terminals, and printers. How to make loopback plugs for testing switch interfaces is also described. Descriptions of cables and loopback plugs for PIC interfaces can be found in the Port Interface Card Hardware Reference.
Rapier Series Switch Figure 21: Pin wiring diagram for a DCE RS-232 Terminal Port (DB9 female connector) male to male modem cable DB9 Male (to switch/DCE) Not connected → (TXD) ← (RXD) ← (CD) (GND) → (DTR) ← (CTS) → (RTS) (RING) Pin 1 DB9 Male (to modem/DCE) 1 2 3 4 5 6 7 8 9 3 (TXD) 2 (RXD) 1 (DCD) 5 (GND) 4 (DTR) 8 (CTS) 7 (RTS) 9 6 Not connected Pin 5 Pin 5 Pin 1 Cable Pin 6 Pin 9 Pin 9 DB9 Male Pin View Notes: (1) (2) Pin 6 DB9 Male Pin View → Output from switch; ← Input to switch C
Hardware Reference 31 Loopback Plugs for Testing Switch Interfaces Loopback plugs are used in conjunction with the Test Facility software to test the physical interfaces on the switch and some PICs (see the “Test Facility” section beginning on page 22 of this Reference, and the Test Facility chapter of the Rapier Series Switch AlliedWare™ Operating System Software Reference).
Rapier Series Switch Rapier Switches and their expansion options support a wide range of interface types, including Ethernet, asynchronous, synchronous, Basic Rate ISDN and Primary Rate ISDN. Each interface type (except Ethernet interfaces on the ATAR026) can be tested independently using the Test Facility software. The following examples show how to test specific interfaces. Test results are displayed with the command: SHOW TEST This produces a display similar that shown in Figure 23.
Hardware Reference 33 Other Interface Tests Refer to the Test Facility chapter of the Software Reference for information on testing other interfaces. If a test fails, please contact your Authorised Allied Telesis distributor or reseller.
Rapier Series Switch LEDs and What They Mean The following tables outline how the Switch, Uplink Module and PIC LEDs report faults and operational activities. Uplink Modules, NSMs, and PICs are expansion options and can be purchased separately. Contact an authorised Allied Telesis distributer or reseller, or visit from www.alliedtelesis.com for more information on purchasing expansion options. Switch LEDs These LEDs are on the front or rear panels of Rapier Switches.
Hardware Reference 35 Table 12: System LEDs on the Rapier 48w LED State Function Power Green The switch is receiving power and the voltage is within the acceptable range. Fault Red The switch or management software is malfunctioning. 1 flash A switch fan has failed. Green An NSM is installed, is receiving power, and is operational. The NSM and its PICs are not ready to be hot swapped. Off No NSM is installed, or the switch has not recognised the NSM.
Rapier Series Switch Table 15: Switch Port LEDs on the Rapier 8/8SC, 8/8MT, 24, 24i, 48, 48i, and 48w LED State Function L/A Green A 100 Mbps link is open Flashing Green 100 Mbps activity is occurring Amber A 10 Mbps link is open Flashing Amber 10 Mbps activity is occurring Green The port is operating at full-duplex Amber The port is operating at half-duplex Flashing Amber Collisions are occurring on the line (Link/Activity) D/C (Duplex/Collision) Table 16: Switch Port LEDs on the R
Hardware Reference 37 Uplink Module LEDs The following tables may be helpful when diagnosing possible operational faults. These LEDs are located on the face-plate of the respective Uplink Module model. Uplink Modules are expansion options and must be purchased separately.
Rapier Series Switch Table20: LEDs on the AT-A40/SC, AT-A40/MT, AT-A41/SC and AT-A41/MT Uplink Modules1 LED State Function Activity/Link/Fault Green A link is open and the port is enabled Flashing green 100 Mbps activity is occurring Flashing amber (and lower LED is Off) The link has failed at the remote end Off No link is present Green The port is operating at full-duplex Amber The port is operating at half-duplex Flashing amber Collisions are occurring Off No link is present Alter
Hardware Reference 39 Table: 21 LEDs on the AT-A42/GBIC Uplink Module LED State Function L/A Green A 1000 Mbps link is open Flashing green 1000 Mbps activity is occurring Flashing amber (and GBIC LED is Off) A TX fault has occurred Off No link is present Green The switch has recognised the GBIC, the GBIC is a valid model Green (and L/A LED is flashing GREEN) The port is operating at full-duplex Amber (and L/A LED is OFF) The switch has not recognised the GBIC, the GBIC is not a valid mode
Rapier Series Switch NSM LEDs NSMs are expansion options and must be purchased separately. They can be used with all Rapier models except the Rapier 48, Rapier 48i, G6, G6F/SX, G6F/LX, and G6F/MT. The AT-AR040 NSM unit has no independent LEDs. See Table 11 on page 34 for information about related LEDs found on the base-unit switch or router. The LEDs in Table 22 are located on the face-plates of AT-AR041 and AT-AR042 NSMs.
Hardware Reference 41 PIC LEDs PICs are expansion options and must be purchased separately. They can only be used if an AT-AR040 NSM is installed in the switch. NSMs (and therefore PICs) can be used with all Rapier models except the Rapier 48, Rapier 48i, G6, G6F/SX, G6F/LX, and G6F/MT. These LEDs are located on the face-plate of the respective PIC.
Rapier Series Switch Table 27: LEDs on the AT-AR023 SYN PIC LED Function Tx Lit when data is being transmitted over the synchronous interface. Rx Lit when data is being received over the synchronous interface. Table 28: LEDs on the AT-AR026 4ETH PIC (two LEDs per port) LED Function Left Lit when the port is operating at 100Mbps and full duplex. Right Lit when a link has been established. Flashing when data is being transmitted through the port.
Hardware Reference 43 Troubleshooting This section provides information on how to detect and resolve problems with the Rapier Switch and its expansion options. Other sources of useful troubleshooting information are: ■ www.alliedtelesis.com/support/software. ■ The Rapier Series Switch AlliedWare™ Operating System Software Reference. Performing the following tasks will eliminate the most common faults. 1. Make sure the power cord is securely connected. 2.
Rapier Series Switch If the port is disabled, someone has used the software to manually disable it. You should find out why the port was disabled before enabling it. Power LED is off This can indicate: ■ A loose power cord or DC power crimp ■ A power supply failure Perform the following steps in sequence: 1. Check that the power cord connections are secure. 2. Check that all switches and circuit protection devices are in the ON position. 3.
Hardware Reference 45 Expansion Options This section provides an overview of the expansion options for Rapier Switches. The following expansion options were available when this Reference was written. See your authorised Allied Telesis distributer or reseller, or visit from, www.alliedtelesis.com to see if any new options are available. Uplink Modules Uplink Modules increase switching capacity by providing a maximum of two extra ports and by allowing switches to be linked together in stacks.
Rapier Series Switch ■ Rapier 8/8MT ■ Rapier 48w NSMs slot into a base-unit switch and either directly provide additional interfaces, or provide multiple slots where additional interfaces can be added.
Hardware Reference 47 PCI Accelerator Cards (PACs) PCI Accelerator Cards (PACs) provide additional processing features or performance, but do not add extra physical interfaces to the switch. A PAC can be installed in the dedicated PAC slot on all Rapier switches except the Rapier 48, Rapier 48i, Rapier G6, and Rapier G6F. PACs should only be installed by authorised service personnel.
Rapier Series Switch Compression PAC-based compression has the following features: ■ Local 32-bit processor for high speed control and data transfer. ■ Dedicated high performance 32-bit compression hardware. ■ High compression ratio Lempel-Ziv algorithm in hardware. ■ 2 MBytes of history memory. ■ Support for up to 127 compression channels.
Hardware Reference 49 Encryption PAC-based encryption has the following features: ■ Local 32-bit processor for high speed control and data transfer. ■ Dedicated high performance 32-bit Data Encryption Standard – DES and Triple DES (3DES) – hardware. PAC DES and triple DES encryption are based on a fast 32-bit device that complies with FIPS PUB 46, ISO DEA-1 and ANSI X3.92 standards. Dual Mode Throughput of an encrypted link can be dramatically increased by using data compression.
Rapier Series Switch Port, Connector, and Cable Combinations This section provides cabling guidelines for each switch model. Table 30: Cable guidelines Model Port Type(s) Connector Type(s) Cable Type1 Maximum Cable Length Rapier 8/8SC 10BASE-T/ 100BASE-TX RJ-45 10BASE-T Category 3 or better 100m (328ft) 100BASE-TX Category 5 or better 100m (328ft) 50/125 or 62.
Hardware Reference 51 Using Windows Terminal and Windows Hyperterminal You can use a PC running terminal emulation software as the manager console, instead of a terminal. There are many terminal emulation applications available for PCs, but the most readily available are the Terminal and HyperTerminal applications included in Microsoft Windows 98, 2000, and XP Professional. In standard Windows installations, HyperTerminal is available from the Communications submenu.
Rapier Series Switch 3. In the “Connect using” field on the Connect To dialog box, select the COM port on the PC used to connect to the switch. and click the OK button. 4. In the COMn Properties dialog box, set port parameters as follows, and click the OK button.
Hardware Reference 53 5. From the main HyperTerminal window, select Properties from the File menu. Click the Settings tab, and set the Properties dialog box as follows. 6. Click ASCII Setup to display the ASCII Setup dialog box, and ensure the following options are not selected: • Echo typed characters locally • Append line feeds to incoming line ends Set other parameters as necessary and click the OK buttons on both dialog boxes to close them.
Rapier Series Switch 7. Save the current session by selecting Save from the File menu on the main HyperTerminal window. This creates a connection icon with the name you assigned in the HyperTerminal group. To use the configuration, double-click the connection icon. When the HyperTerminal window appears, press the Enter key several times; the switch’s login prompt is then displayed. Restricted Procedures This section contains procedures that should only be performed by authorised service personnel.
Hardware Reference 55 2. Restart the switch. Restart the switch, either by using a pen or pencil to operate the recessed reset button on the front panel, or by using the terminal to log in and enter the command: RESTART REBOOT See “To Log In” on page 12 for more information on how to log in. 3. Enable diagnostics mode during startup. During the switch start-up process, at the prompt: Force EPROM download (Y)? press [Ctrl/D] on the terminal to enter diagnostics mode.
Rapier Series Switch Installing a PAC PACs can be installed in all Rapier switches except the Rapier 48, Rapier 48i, Rapier 48w, Rapier G6, and Rapier G6F. PACs should only be installed by authorised service personnel. Unauthorised opening of the switch’s lid may cause danger of injury from electric shock, damage to the switch, and invalidation of the product warranty. Before you begin 1. Check that you have the correct tools and equipment. You will need a medium-sized posidrive screwdriver. 2.
Hardware Reference 57 Figure 27: Location of PAC slot and pillar mounts on a Rapier base board PAC slot Boot EPROMs Fan PAC pillar mounts 8PACslot 6. Insert the PAC. Position the PAC over the PAC slot on the switch base card, making sure that the support pillars located on the switch base card are aligned with the holes provided on the PAC. This ensures that the connector on the PAC is correctly aligned with the slot on the switch base card. Press the connector firmly into place.
Rapier Series Switch correctly plugged into the slot on the switch’s base board. Repeat the installation process, paying particular attention to Step 6. Use the show system command again, and if the display is still not correct, contact your authorised Allied Telesis distributor or reseller. If you have any difficulty with the PAC at any time, contact your authorised Allied Telesis distributor or reseller and quote the serial numbers of both the base card on the switch and the PAC.
Hardware Reference 59 Next, check the PAC’s status using the command: SHOW LOG to display a log of PAC events. A typical display is shown in Figure 29. Figure 29: Example output from the SHOW LOG command for a Rapier switch with an AT-AR061 ECPAC card installed Date/Time S Mod Type SType Message -------------------------------------------------------------------------15 00:05:50 4 ENCO ENCO PAC 7751 Found.
Rapier Series Switch Figure 30 shows a typical output. The status of the test will be shown in the right-hand column. For further information on the meanings of the other figures, see the “Test Facility” chapter of your switch’s Software Reference.
Hardware Reference 61 Replacing Boot EPROMs All Rapier switches except the Rapier 48w have two 512 kByte boot EPROMs. The boot EPROMs contain bootstrap code, which loads the main code from a software release file in FLASH memory. In rare circumstances the boot EPROM(s) may need to be changed. Boot EPROMs should not need to be replaced, except in rare circumstances. Contact your Authorised Allied Telesis distributor or reseller before replacing any boot EPROMs. To change the boot EPROMs 1.
Rapier Series Switch Figure 31: EPROM locations Boot EPROMs (Rapier 8/8MT, 8/8SC, 16F-FX/MT-RJ, 16Fi-FX/MT-RJ, 16F-FX/SC, 16Fi-FX/SC) PAC slot Boot EPROMs (Rapier G6, G6F-LX/SC, G6F-SX/SC, and G6F-SX/MT-RJ) Fan r24eprom 7. Insert the new boot EPROMs. Insert the new boot EPROMs one at a time, using as a reference the location number printed on the CPU board (e.g., “0” and “1”) and Figure 31 above. Check that the boot EPROMs are firmly seated.
Hardware Reference 63 Figure 32: Example output from the SHOW INSTALL command Install Release Patch -----------------------------------------------------------Temporary Preferred flash:load\86s-210.rez Default EPROM (86s-2.1.0) -----------------------------------------------------------Current install -----------------------------------------------------------Preferred flash:load\86s-210.
Rapier Series Switch For More Information Document set The complete document set for Rapier Series switches includes the following: ■ The Rapier i Series Switch Safety and Statutory Information booklet, which contains safety information for all Rapier switches except the Rapier 48w ■ The Rapier Series Switch Quick Install Guide, which describes how to install all Rapier switches except the Rapier 48w ■ The Rapier 48w Switch Installation and Safety Guide, which describes how to install the Rapier
Hardware Reference CD-ROM Contacting us C613-03020-00 REV K 65 Some products ship with a Documentation and Tools CD-ROM, which includes: ■ the complete document set ■ Adobe® Acrobat® Reader® ■ AT-TFTP Server ■ Supported MIBs ■ How-To Notes, white papers, Microsoft® Visio® stencils and other resources ■ Tryouts of networking software With locations covering all of the established markets in North America, Latin America, Europe, Asia, and the Pacific, Allied Telesis provides localized sales a
